GTE Omni Si Database Technical Practices Manual

							TL-130400-1001Table 7.6Entry Fields for Record Code CH
COL.COL.VALID
NO.NAME
ENTRIESCOMMENTS
12-i4Old AccessOOO-### = numberEnter the access code that is to be
Codetemporarily changed.
-Columns 12-14 and 15-l 8 are mutually
exclusive. If you mark this field, do not mark
columns 
15-l 8.
. .-This feature can only be used for intercept,
Attendant Console(s), hunt group, or agent
group.
15-18Old Station
0000-9999 =This field defines the station number that is to
Numbernumberbe temporarily changed.
---- 
= not-Right justifiy three-digit numbers.
selected-Columns 12-l 4 and 
15-l 8 are mutually
exclusive. If you mark this field, do not mark
columns 12-l 4.
-This number can only refer to 
DNs for lines,
Attendant Console(s), hunt groups, or agent
groups.
19-22New Station
Number0000-9999 =number
--- 
= notselectedEnter the station number of the new
(temporary) destination.
-Right justify three digit numbers.
-This number can only refer to 
DNs for lines,
Attendant Console(s), hunt groups, or agent
group.23-25New Code Type
000-225 =Enter the new code type to be temporarily
number
used.-- = not-This number can only define an intercept
selectedroute, Attendant Console(s), recorder
announcer, or agent group.
26-29New Code Type0000-9999 =Enter the new code type identifier to be
Identifiernumbertemporarily used.
--- 
= not-Right justify three-digit numbers.
selected 
						

							TL-130400-1001
Record Code DF:7.7 Record Code DF, Figure 7.7, defines the default line divertCPG 5efaultcondition for lines assigned a divert destination on Record Code
LD, columns 45-48.Record Code DF:
7.7 Record Code DF, Figure 7.7, defines the default line divert
CPG 5efaultcondition for lines assigned a divert destination on Record Code
LD, columns 45-48.
‘---------r---rI
I, TI 
6
,---------------------------------------------------------------~
II ; I.I
iI
I: FII 5IIIIIIIIII _ I I _ I’ /-.“I’ /-.“III
1F1FIIC; L CtC; L CtIIS---N RS---N RI I
:: 5-q 81: :;I IIIM‘0 EI E y;I I
1.3ID TII IIIII IIIII. .IIII v 01I E NII I
IIR II I
IIT ,I I
II
I IIII II I
I II IIIII
I II IIII III
I IIII I
I IIII III
I II III
I II I
IIIIIIIIIIIIIIIIIIII
r-T-r-C-T-t-r-t-r-~-T-T-T-T-T-T-T-T-T-T-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~r-T-r-C-T-+-r-t-r-~-T-T-T-T-T-T-T-T-T-T-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~
~7~8~9~0~1~2131415161718~910111213l415l6l7l8l9l0l1~2~31415161718l910~112131415,~7~8~91011121314151617181910111213141516171819101112131415161718l9101112131415,111111111111111111111212121212121212121213131313131313131313l4i4l4l4l4l4~111111111111111111111212121212121212121213131313131313131313l4i4l4l4l4l4~
t-+-+-+-u-+-~-+-+-+-+-+-+-+-+-+-+-+-+-+-+-~-+-+-~-+-+-+-+-+-+-+-+-+-+-+-+-+-~t-+-+-+-u-+-~-+-+-+-+-+-+-+-+-+-+-+-+-+-+-~-+-+-~-+-+-+-+-+-+-+-+-+-+-+-+-+-~1010,51~!FI I I I I I I I ,I I ,I I I,,, I I  I ,,I I I I I I I I I I  I I101051D!FI I I I I I I I I I I I I I I I I I I I  I I I I I I I I I I I I I  I IL-L-L-~-L-L-_~--L-L-~-L-~-~-~.-~-~-~L-L-L-~-L-L-_~--L-L-~-L-~-~-~.-~-~-~-~-~-i-I-~-~-~-~-~-~-~-~-~-~-~-~---~-- . . . 8-~-~-i-I-~-~-~-~-~-~-~-~-~-~-~-~---~-- . . . 8
I! F!I
‘---------r---rI
I, T,---------------------------------------------------------------~
iI 6II ; I.II
Figure 7.7Record Code DF: CPG Default Data Sheet
Table 7.7
Entry Fields for Record Code DF
COL.NO.
12-13
I
COL.NAME
Line Divert
ConditionVALID
ENTRIES‘
BY = divert if busy
NA = divert if no
answer
BN = divert if
busy or no answerCOMMENTS
Mark this field with the system default divert
condition.
-This record code makes it unnecessary to
program a divert condition for each line
(Record Code LM, columns 28-29) if all
system stations have the same divert
condition.
If the majority of lines have the same divert
condition, then that condition can be given
here.-Divert conditions that are different from the
default value given here can be assigned to
the various lines on Record Code LM. 
						

							TL-130400-1001LINE8.0 This section describes the record codes required to
ASSIGNMENTdefine the various system lines. The following record codes are
required:
l Record Code LD defines the primary directory number for all
lines in the system and provides additional line information.
l Record Code LM is an extension of Record Code LD.
-=-.”. .l Record Code LA defines the various line or DSS (Direct Station
Select) appearances.
l Record Code LI is not input by the customer 
						

							TL-130400-1007
Record Code LB:8.1 Record Code LD, Figure 8.1, defines the primary directory
Line Datanumber for every line in the system. If an Analog/Digital
Featurephone has additional appearances of control lines such
as CO (Central Office), non-primary control, or data lines, an
entry on this record code is needed for each line type. Use this
record code to route non-working lines to a changed number
intercept. Line circuits programmed on the Attendant Console
(Record Code AT) or office features circuit (Record Code OC) do
not require an entry on Record Code LD. If the sytstem is
s-1equipped with the PD-200 Data Option, this record code must
list the 
APM’“/SPM” physical location.
T---------T-------r---__--_-T-----T---T---_---_--___--------_------------I
;T T T T: ‘. *’ i.II,66661IT,a
I,4444,114’I4 ;2II’34I,I11:II1 ,I1I
IITIT! T ;I5 I5I 5
i3I4I4
16I1I3II I1 I1I TI
ILINEICKI-.
I
/ 1 1I II-,-t-,-;-,-$-$-,-,-t-t-~-~I1 I1 I1 I1 11 11 II 11 11 I1 1212121212121212121213131313131313131313l4l4l4l:7;8;9,0,1 12131415161718191011 12131415161718191011 1213l415161718191011 121~-+-+-u-+-+-+-+-~-~-~-+-+-+-~-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-!,-l~.55iLlDl I I I I I I I I  I I I I I I I 1 I I I I I II I I I I I  I liL --L--C-L-L-L-*-~-~-~-*-~-~-~-*-~_~-~-*-~-~--L-~-~-*-~-~-~-~-~-~---J
r---r-------p-----r-r----------------------------------------------------~-~
; T;I RII A,I N,I Sl,
I
II GfI1 0,
x561*zI1 DIII E,
T22i%%II I’ I
w:ZEI
I1 I
I1 IT257 1
mE%I1 I1 IIT2581ES1II II1 IT25DlI I
T%zI
I
IIII
I1 I
I I
I1 I
III1 I III IIII1 I IIk-T-t-T-T-T-t-T-t-t-t-T-T--r-T-T-T--r-T-T-T-T-T-T-T-T-T-T-T-T-r-T-iL-41414141414141415151515151515151515161616,6i6l61616l6l6l7l7l7l7i7lI8 I1314151617,819,0,112,3,415,6,718191011121314151617181910111213141IO IL-L-L-L-L-L-L-I-L-I-~_~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-----~-J
Figure 8.1Record Code LB: Line Data SheetD-l 44SVR 5210 
						

							Table 8.1Entry Fields for Record Code LDCOMMENTS
equippedline circuits in the system.
-Directory numbers can be chosen in 
three-and/or four-digit patterns.
digit line directory-Three-digit numbers must beright justified
-Dashes must be entered in this field if the
line is used for an APM or SPM that is used in
support of the PD-200 Data Option.
-The 
APMs/SPMs are not accessed by a line
number, but by an X.121 address.
-This record code is only used to provide the
sical location of the APMsSPMswithinthe
-ADIFPmust appear on a VCIP, VPLO,
VPLl, VP20 (voice/voice & data), or DVC line
integrated
Featurephone
APM =
Asynchronous
Packet Managercard.
-An APM must appear on a VPLO, VP20
(voice 
& data or data only), or VP21 line card.
-If necessary, an APM can be assigned to a
VPLl; however, it is recommended to use the
SPM =SynchronousVPLO card, which is designed to support the
low-speed APM.
Packet Manager-An SPM must appear on a VPLO, 
VPLl,
DFPA = DigitalVP20 (voice & data or data only), or VP21 line
Integrated
card.
Featurephone with-APM and SPM should be left justified in the
Asynchronousfour columns; e.g., APM- and SPM-.
Packet Manager-A DFPA must appear on a VP20 (voice 
&
PACT = 
program-data) line card.
mable Attendant-A PACT or POTS must appear on a POTS
Consoleor OFFP line card.SVR 5210 
						

							TL-130400-1001Table 8.1Entry Fields for Record Code LD (Continued)COMMENTS
instrument line
columns 28-29 (this allows
-If columns;6-19 are markedPOTS,PACT,
AlFP, DFPA, DIFP, APM, or SPM, columns
20-25 must not be dashed.
-If columns 16-l 9 are dashed, columns
20-25 must be dashed.
-All card locations must be defined on
Record Code FR.
Which card slot within the group is this card?
-Inorder toprovidedasequential
appearance of line numbers on the CPG (in
groups of eight 
), list all eight circuits of a line
card for each group and card slot in the
following order: 4, 0, 5, 1, 6, 2, 7, 3.
-The reason for this order is that this is the
order in which the circuits are connected on
the backplane of the system.
-The circuit numbers assigned to a digital
IFP used for (CD-100 data) voice transfer
can only be circuits O-3. Circuits 4-7 are
assigned to data connections.
-This number must match the limits given to
the card type at the specified physical
Is the line in service or out of service? 
						

							TL-130400-1001Table 8.1Entry Fields for Record Code LD (Continued)
COL.COL.VALID
NO.NAME
ENTRIESCOMMENTS
28-29
. . . .Line Type
--1CO = central office
NP is used for a logical line, which appears in
line, as in keysoftware only and needs no line card.
system CO line-- (a double dash) is used for all tip and ring
(Featurephone)type telephones (e.g., the FeatureComm” and
DA = data lineAnswerComm” 1 and 2).
(DIFP)When defining line 2 on a PACET
Li = CAS(Programmable Attendant/Agent Console
,_ Main/ACD agentElectronic Telephone), mark this field --.
line-If this field is marked 
Ll, Record Code NC,
NP = non-primarycolumns 30-31, must be marked HS (this
control lineallows hookswitch flash in COS).
(Featurephone)-If columns 16-l 9 are marked POTS, this
NW = nonworkingfield must be marked Ll or dashed.
line-If columns 16-l 9 are marked POTS, this
PC = primaryfield must be marked Ll or dashed.
control line-If columns 16-19 are marked PACT, this
-- = none of thefield must be marked 
Ll.above, e.g., POTS
-If columns 
16-l 9 are marked AIFP or
telephoneDFPA, this field must be marked CO, NP, or
PC.-If columns 16-19 are marked DIFP, this
field must be marked CO, DA, NP, or PC.
-If columns 16-19 are marked APM or SPM,
this field must be marked DA.
-If columns 16-l 9 are dashed, this field
must be marked NW.
-The physical location fields for a line
marked NP must match that of the controlling
IFP.-If an entry of NP or CO is made, there must
be available space in the system tables to
assign a line software ID. A maximum of 256
lines of all kinds is allowed.
-If this field is marked NP, station silent
monitor (Record Code NC, columns 72-73)
will not work.
-Each IFP must have one and 
only one
primary control line. 
						

							TL-130400-1001Table 8.1Entry Fields for Record Code LD (Continued)COMMENTS
-If this line is to belong to an intercom group,
this field determines which group it belongs to.
-Each line appearing on the same IFP can
be in the same or different intercom groups.
-If two lines have a DSS appearance of each
ns 28-29 (line type) are marked
, 
Ll, -- or NW, this field must be
-The number entered here must be defined
on Record Codes DC and DD.
-If columns 16-19 are marked POTS, PACT,
AIFP, DFPA, or DIFP, these columns must not
be dashed.
-If columns 16-l 9 are marked APM, SPM,
or dashed, these columns must be dashed.
34-35Class of Service00-l 5 = numberAssign the n-displayable class of service for
N-Displayablethe line.
-Each line appearing on the same instrument
can have the same or different n-displayable
classes of service.
-The number entered here must be defined
on Record Code NC.
-If columns 16-19 are marked POTS, PACT,
AIFP, DFPA, or DIFP, these columns must not
be dashed.
-If columns 16-l 9 are marked APM, SPM,
or dashed, these columns must be dashed. 
						

							TL-130400-1001Table 8.1Entry Fields for Record Code bD (Continued)COMMENTS
O-7 =FRLvalueAssign the FRL value given to this line.
-This can only be assigned if the FRL feature
is in effect (see Record Code OF, column 54).
-A value of 0 is the most restrictive; a value
of 7 is the least restrictive.
-This value is compared to the FRL value of
the trunk that the user is trying to access.
-If the FRL value of the user is the same as
or greater than the FRL value given to the
trunk, the call can be made.
-If the FRL value of the user is less than the
FRL value given to the trunk, the call will be
-If columns16-19 are marked APM,SPM,
or dashed, these columns must be dashed.
group, this field is the primary group.
-The pickup group to which a member of an
extended pickup group belongs is defined on
Record Code ED.
-The Attendant Console cannot be in a
pickup group. The system maximum is 127
pickup groups, with no limit to the number of
members in each group.
-If a station line appears on the DSS, having
this feature is redundant.
MITE: If the line type is DA, Ll, or NW
(columns 
28-29), this field must be dashed.
40Dial Call Pickup:E = extended groupIf the line belongs to an extended pickup
Extended
- = dial callgroup, enter an E.
Pickup Grouppickup group-Record Code ED must be completed before
this entry can be made.
-If the line type is DA, 
Ll, or NW (columns
28-29), this field must be dashed.
41-42Group Speed01-48 = numberThis field determines the speed calling group
Calling-- = N/Anumber assigned to this station.
-Record Code GC must be completed before
this entry can be made.
-If columns 
16-l 9 are marked APM, SPM,
or dashed, these columns must be dashed.
-If the line type is DA (columns 
28-29), this
field must be dashed. 
						

							TL-130400-1001COL.NO.Table 8.1Entry Fields for Record Code LD (Continued)COL.VALID
NAMEENTRIESCOMMENTS
43-44Individual
00-30 = number
Speed CallingIf the line is a member of an individual speed
-- = N/A
calling list, assign the list it belongs to.
_ List Number.-Only one station can be assigned to each
individual speed calling list.
-A system maximum of 31 stations can have
this feature.
,.-If columns 16-19 are marked APM, SPM,
or dashed, these columns must be dashed.
-If the line type is DA (columns 
28-29), this
field must be dashed.
45-48Divert
0000-9999 =Assign the divert destination (call forwarding)
Destination
station number
type.Identifier
0-N)-It can be a line, pilot number, trunk group,orintercept route, VMX mailbox, or external
pilot number (PN)
directory number.
of a hunt group-If the entry is SC, then the speed calling list
(right justify
must not contain dashes because the remote
three-digitcall forward feature is accessed through an
numbers)
entry in the individual speed call list that stores
0000, 0064, 0128,the remote number.
or 0192 = console-A line cannot divert to itself.
number (AT)
-If a station number is listed, it must be
0000-0063 =defined in columns 12-15 of this record code.
trunk number-If a pilot number of a hunt group is listed, it
m-w- = N/Amust be defined on Record Code HG,
directory numbercolumns 12-l 5.
and individual-If an attendant number is 
listed,.it must be
speed call listdefined on Record Code AT.
(VW TO)-If a trunk number is listed, it must be defined
0001-0008 =on Record Code TC.
speed call list-The additional information needed to
entry number (SC)implement this feature is found on Record
Code LM, columns 28-31.
-If columns 16-19 are marked APM or SPM,
these columns must be dashed.
-If columns 16-l 9 are dashed, these
columns must be either 0003 (vacant #) or
0011 (changed 
~7).-If the line type is DA (columns 
28-29), this
field must be dashed.
-If the line type is CO (columns 
28-29), this
field must be marked with a trunk number and
Record Code LM, columns 28-29, must be
marked DA.