GTE Omni Si Database Technical Practices Manual

							TL-130400-1001
Table 15.5Entry Fields for Record Code PDCOMMENTS
er number must be unique
-Eachlocationmust beunique.
Which card slot within the group is this card?
18-19Baud Rate03 = 300 baudIndicate the baud rate or speed of the printer.
-- = 1,200 baud-If an Axiom printer is used, this field can be
defaulted.
20-21ParityOD = odd parity
-- = even parityIndicate the parity (used for error detection) of
the printer.
-If an Axiom printer is used, this field can be
defaulted.
22-23Paper FormWD = wide print-Indicate the paper form by checking the
out (at least 
40-number of characters that are typed by the
80 columns wide)printer on a per line basis.
-- = narrow-If an Axiom printer is used, this field can be
print-out (40-80defaulted.
columns wide)
24Stop Bit2=two stop bits
- = one stop bitIndicate the number of stop bits needed to
stop the data flow.
-If an Axiom printer is used, this field can be
defaulted.
25
26Word Length in8 = eight-bitIndicate the word length that is sent to the
Bitswords
printer.
-=seven-bit-If an Axiom printer is used, this field can be
wordsdefaulted.
Parity InhibitY = printer does notEnter Y if the printer needs a parity inhibit bit.
require a parity bit-If an Axiom printer is used, this field can be
- = printer doesdefaulted.
require a parity bit
SVR 52107187D-285 
						

							TL-130400-1001Record Code RN:15.6 Record Code RN, Figure 15.6, indicates when it is
Room Numbernecessary to precede a room station number with an access
First Digit Translationcode for room-to-room calling.
r---------r-r---------+--------------------------------------------------------~
I
I
I
I
I
f
rI ;C.
I :
L.
D-286
III 1II
I
I
’ -t-t-r-s-t-T-t-T-T-t-T-T-T-T-T-T-T-T-T-T-~-~-~-~-~-~-~-~-~-~-~--: :-:;:I I1 I1 I1 I1 I1 I1 I1 II 1212121212121212121213131313131313131313l4l4l4~718191011 12131415161718191011 12131415161718191011 12131415161718191011 I21-+-+-+-+-
t
-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-~-+-+-+-+-+-~314lOlRlN 01I I I I l I I l I I I I I I I I l I I 1 l 1 1I I I I I I-L-LJ-L- --C-l-~-~-*-~-l-l-~-~-*-~-~-~-~-*-~-~-~-*-~-~-*-~-~-~--~--’.
8;
EIII
I
I
I
I
I
I
-48 I
0 I
-1
Figure 15.6Record Code RN: Room Number First Digit Translation Data Sheet
7187SVR 5210 
						

							-TL-130400-1001
Table 15.6Entry Fields for Record Code RNCOMMENTS
This field determines the first digit of a 
three-or four-digit room directory number.
-This number is preceded by an access
code for room-to-room calling.
digits must also be entered.
er first digit must be unique
column 12 is the first digit of a th
station numbersroom directory number, a four-di
4DG = firstdigitofdirectory number, or the number
numbers that dobeing defined, a move or a change call to that
number is routed to an intercept condition.
-Intercept conditions must be defined on
Record Code IR.
his 
fielddetermines themissingdigit required
for three-or four-digit room station numbers
or specifies the intercept routing number
12 = 3DG missingassigned to an intercept condition.
-If a missing digit is required, this field also
selects the missing digit.
If a missing digit is not specified, the console
station number display will display L followed
by a three-digit station number.
-If the missing digit is specified, the console
station number display will display themissing
identifier must be O-15.
-If the code type is 3DG, the code type
identifier must be O-9 or 12.
-If the code type is 
4DG, the code type
identifier must be 15. The numbers O-15 are
the intercept conditions defined or Record
Code 
IR. Only one of these intercept
conditions can be used in support of Record
ndition must be defined on
SVR 5210
8187D-287 
						

							TL-130400-1001Record Code CL:15.7 Record Code CL, Figure 15.7, defines routing information
Class of Call-based on the first two digits (00-99) of the calling station’s
Controlled Routingassigned directory number or room number.
T---------T---‘---------------I--------’------------------------------------1ITII
III
I
IIIIII1II
Figure 15.7Record Code CL: Class of Call-Controlled Routing Data Sheet
D-2888187SVR 5210 
						

							TL-130400-1001Table 15.7Entry Fields for Record Code CLCOMMENTS
-If the room or line directory numbers are
three-digit numbers and a missing digit is
listed on Record Code RN (columns 
16-17),enter the missing digit in column 12. Enter the
first digit of the three numbers in column 13.
-If the room or line directory numbers are
three-digit numbers and no missing digit is
listed on Record Code RN (columns 16-l 
7)enter 0 in column 12. Enter the first digit of the
three numbers in column 13.
-If the room or line directory numbers are
four-digit numbers, enter the first two-digits
of the room or line directory numbers in
columns 12-l 3.
ined on Record
Console
INTC = interceptwhen the access code for call control routing
is activated.
18-21Destination
Identifier0000-9999 orIndicate the destination to which all calls from
000-999 = the linethe same hundreds group will terminate when
directory number ifthe access code for call control routing is
the destination is a activated.
line-The destination can be any of the following:
A three-digita room station number, a line directory
number must havenumber, an Attendant Console, or an intercept
a blank before it.routing number.
0128 = Attendant-If the destination is a line directory number,
Console 0that number must be defined on Record Code
0064 = AttendantLD.Console 1-If the destination is an Attendant Console
0192 = either of thecircuit, that console circuit must be defined on
two AttendantRecord Code AT.
Consoles-If the destination is an intercept condition,
0000-0015 =that condition must be defined on Record
intercept routingCode IR.
number
SVR 5210
8187D-289 
						

							_-, .TL-130400-1001
Record Code TL:15.8 Record Code TL, Figure 15.8, assigns printers to the
Transaction Recordfunction of the transaction record. All printer numbers indicated
Controlby the printer identification number must be valid printer numbers
on a PD form. The four printers are given the following values:
* Printer No. 0 is assigned value 01.
e Printer No. 1 is assigned value 02.
l Printer No. 2 is assigned value 04.
l Printer No. 3 is assigned value 08.
If more than one printer is designated, use Table 
15.8A.Table 
15.8A Printer ID
NumberPrinter
ID
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15Printer
Number(s)
None
0
1
0, 1
2
0, 2
1,2
0, 1, 2
3
0, 3
1, 3
0, 1, 3
2, 3
0, 2, 3
1,293
0, 1, 2, 3
D-2908187SVR 5210 
						

							TL-130400-1001iTI
IEI
I1I
I
TI
I3”
II
EiMAID 
;I STATUS ,
II
I‘T---r---
1716191011121314,5c-+-+-+-+-+-+-+-+-1319101Tl LI I I IL-A-A.-A--L-L-A-A-A._
141414141141516171I.-A.-J.-l-,
I
II
II
II
II
II
;-T-;-T-;-T-;.I1 I1 I1 I1 12121;161718191011 I:
+-+-+-+-+-+-+-DISPLAY I
--7---J
’ !; IPI 
I I I’ IiI
IIii ;
I
III
II
II
II-
T-~-
T-~-
T-~-,-~-,-~-~-~-~-~-~-~-I!
!12121212121212131313131313131313131414!13141516171819101112131415161718191011-+-+-+-+-+-+-+-c-+-+-+-+-+-+-+-+-+-+-+-I I I I I I I I I I I I I I I I I I I
-~-~-~-~-I-*-~-~-~-~-~-~-*-~-~-~-~-~-~-
Figure 15.8Record Code TL: Transaction Record Control Data Sheet
SW 52108187D-291 
						

							rTL-I 30400-l 001
Table 15.88
Entry Fields for Record Code TLCOMMENTS
If this field
ismarked AC,DE,or BT,
umns 
14-l 5 must be marked 01-l 5.
= transaction record is printed when
ssage metering is activated.
= transaction record is printed when
ssage metering is deactivated.
= transaction record is printed when
-If only one printer is used, enter the printer
value 01, 02, 04, or 08.
-If more than one printer is used, enter the
sum of the printer values from Table 
15.8A(e.g., if printers 0 and 1 are used, enter 3; if
printers 2 and 3 are used, enter 12).
16-17Room Status AC
Print StatusIndicate the conditions required for a print-
DEout to be activated when this feature is used.
BTAC = transaction record is printed when
ormessage metering is activated.
--DE = transaction record is printed when
message metering is deactivated.
BT = transaction record is printed when
message metering is activated or deactivated.
-- = N/A
18-19Room Status01-l 5 = printerPrinter Number valueAssign the printer(s) that will give a print-out
when this feature is used.
Identification-- = N/A-If only one printer is used, enter the printer
value 01, 02, 04, or 08.
-If more than one printer is used, enter the
value from Table 
15.8A (e.g., if printers 0 and
1 are used, enter 3; if printers 2 and 3 are
used, enter 12).
D-2928187SVR 5210 
						

							TL-130400-1001Table 15.88Entry Fields for Record Code TL (Continued)COMMENTS
Indicate the conditions
out to be activated whe
AC = transactionrecordisprintedwhen
message metering is activated.
DE = transaction record is printed when
message metering is deactivated.
BT = transactionrecord is printed when
e metering is activated or deactivated.
rinter Numberwhen this feature is used.
-If only one printer is used, enter the printer
value 01, 02, 04, or 08.
-If more than one printer is used, enter the
sum of the printer values (e.g., if printers 0 and
1 are used, enter 3; if printers 2 and 3 are
used, enter 12).
out to be activated when
DE = transaction record is printed when
message metering is deactivated.
BT= transaction record is printed when
-If only oneprinter isused, enter the printer
value 01, 02, 04, or 08.
AC = transaction record is printed when
message metering is activated.
DE = transaction record is printed when
message metering is deactivated.
BT= transaction record is printed when
SVR 5210
8187D-293 
						

							TL-l30400-1001
Table 15.85Entry Field for Record Code TL (Continued)COMMENTS
Assign theprinter
when this feature
used,enter theprinter
-If more than one printer is used, enter the
sum of the printer values (e.g., if printers 0 and
1 are used, enter 3; if printers 2 and 3 are
message metering is deactivated.
BT = transaction record is printed when
Printer Numbervaluewhen this feature is used.
Identification
-- = N/A-If only one printer is used, enter the printer
value 01, 02, 04, or 08.
-If more than one printer is used, enter the
sum of the printer values (e.g., if printers 0 and
1 are used, enter 3; if printers 2 and 3 are
used, enter 12).
36-37Maid Status
Print StatusAC
DE
BT
ormmIndicate the conditions required for a 
print-out to be activated when this feature is used.
AC = transaction record is printed when
message metering is activated.
DE = transaction record is printed when
message metering is deactivated.
BT = transaction record is printed when
message metering is activated or deactivated.
-- = N/A
38-39Maid Status01-l 5 = printerAssign the printer(s) that will give a print-out
Printer Number valuewhen this feature is used.
Identification-- = N/A-If only one printer is used, enter the printer
value 01, 02, 04, or 08.
-If more than one printer is used, enter the
sum of the printer values (e.g., if printers 0 and
1 are used, enter 3; if printers 2 and 3 are
used, enter 12).