GTE Omni Si Database Technical Practices Manual

							TL-130200-1001Touch Calling Receiver
Test
Automatic Testing
Procedures
Automatic TestResults
52109.17 This test checks a specified PCM Dual Tone Multiple
Frequency receiver (PDTMF, FB-17203-A) for proper tone
reception. The test may be conducted either automatically or
manually. The automatic test procedure places a particular time
slot (information memory location) into the control memory of the
PDTMF. The microprocessor address of the Multi-Processor
Buffer 8085 (MPB85, FB-17215-A) is monitored for correct
tone translation. If the correct translation occurs, a new tone is
tested. An error message is displayed if this translation is
incorrect. The manual test links a specified touch calling phone
to the PDTMF. As each number of the touch calling phone is
depressed, a DTMF tone is sent to the PDTMF. A description of
the DTMF tone is displayed as it is translated by the PDTMF.
9.17.1Use the following steps to conduct the automatic Touch
Calling Receiver Test:
1. Select option “9” from the Menu of Test Options. The system
responds:
TOUCH CALLING RECEIVER TEST
DO YOU WISH TO USE THE TONE CARD?
IF YES TYPE 
“Y” , IF NO TYPE “N”2. Type 
“Y’ if there is a PDTMF card in the system. The system
responds:
ENTER THE LOCATION OF THE TCR TO BE TESTED
FILE NUMBER (A -- 
> D) > > . .
3. Type the correct file letter of the TCR. The system responds:
SLOT NUMBER (0 -- 
> 11) > >4. Type the correct universal card slot number. The system
responds:
CIRCUIT NUMBER (0 -- 
> 3) > > . .
5. Type the correct circuit number. The test begins.
9.17.2 The following automatic Touch Calling Receiver Test
results may appear:
1. If the PDTMF passes the test, the system responds:
TCR PASSES TEST
2. If the PDTMF fails the test, the system responds:
TCR FAILED DIAGNOSTIC
8187M-365 
						

							rTL-130200-1001Manual Testing9.17.3 Use the following procedures to conduct the manual
ProceduresTouch Calling Receiver Test:
M-3661. Select option “A” from the Touch Calling Receiver Test Option.
The system responds:
TOUCH CALLING RECEIVER TEST
DO YOU WISH TO USE THE TONE CARD?
IF YES TYPE 
“Y”g IF NO TYPE “N”2. Type “N 
“.The system responds:
A TOUCH CALLING PHONE IS TO BE USED TO SEND
TONES TO THE TCR RECEIVER. ENTER THE LOCATION
OF THIS PHONE.
FILE NUMBER (A -- 
> D) > > . .
3. Type the correct file letter. The system responds:
SLOT NUMBER (0 -- 
> 11) > >..4. Type the correct universal card slot number. The system
responds:
CIRCUIT NUMBER (0 -- 
> 7) > >..5. Type the correct circuit number. The system responds:
ENTER THE LOCATION OF THE TCR TO BE TESTED
FILE NUMBER (A.-- 
> D) > >..6. Type the correct file letter of the TCR. The system responds:
SLOT NUMBER (0 -- 
> 11) > >..7. Type the correct universal card slot number. The system
responds:
CIRCUIT NUMBER (0 -- 
> 3) > > . .
8. Type the correct circuit number. The system responds:
ANY DIGIT WHICH IS DEPRESSED WILL BE ECHOED ON
THE TELETYPE. WHEN YOU WISH TO EXIT FROM THIS
TEST, TYPE ANY CHARACTER 
> >..9. Depress any digit and monitor the terminal tone description.
10. After all digits are checked, type any character on the
terminal to end the test.
81875210 
						

							TL-130200-1001AAccess Recent Change, M-281
Access On-Line Maintenance, M-85
Acrxunting Reports, M-248
Add-a CAS Main/ACD Agent Group, M-305
Agent 
-Data Displays and Changes, M-300
Agent Group Call Waiting Levels, M-315
Agent Group Delay Routing Display, M-314
Agent Instruments, M-60
Agent Position Status Display, M-300, M-302
Agent Status Report, M-293
Alarms, M-l 78
Alarm Command Codes, M-80
Attendant and Busy Lamp Display Unit, M-60
Attendant Console Code Display Fault, M-108
Attendant Interface Card, M-359
Attendant Interface Card Test Testing Procedures, M-360
Automatic Circuit Assurance Log Request Commands, M-43
Automatic Testing, M-340
Automatic Testing Procedures, M-365
Automatic Test Results, M-365
BLDU Unit Troubleshooting Procedure, M-160
Bulk Downloading Commands, M-66B
Bulk Input Command, M-788
Call Store, M-236
Call Waiting Data Menu, M-313
Call Waiting Data Menu Access, M-313
F=TL-130000-1001 O=TL.130100-1001M=TL-130200-1001I=TL-130300-1001D=TL-130400-1001S=TL-130500-1001A=TL-100000-1001Features
OperationMaintenanceInstallationData 
BaseSystem ConfIguration ADMP UsersGuide 
						

							TL-130200-1001
Card List, M-17
CALL TRACING, M-21 1
Call Tracing Examples, M-217
Cancel a Trend Report, M-299CASACD Source Group Report, M-291
CAS 
Main/ACD Data .-Menu Instrument, M-31 8
CAS 
Main/ACD Help, M-284
CAS 
MAlNiACD Source, M-295
CAS 
Main/ACD Supervisor Options, M-282
CAS 
Main/ACD Supervisory Recent Change, M-299
CAS 
Main/ACD Trunk Data Menu, M-306
CAS 
Main/ACD Trunk Data Transactions, M-307
Change a Repertory Dial Key Set, M-319
Change a Source Message, M-312
Change Alternate Destination of an Agent Group, M-317
Change Call Waiting Indicator Levels, M-318
Control Card Removal and Replacement, M-20
Change Day/Night Mode 
(87), M-321
Change Delay Routing of an Agent Group, M-315
Change FADS Automatic Dump Period, M-297
Change the FADS Automatic Dump Selections, M-297
Change FADS Data Collection Start Time, M-298
Change FADS Periodic Data Collection Period, M-296
Change First Recorded Announcement, M-31 6
Change Night Destination of an Agent Group, M-305
Change Recorded Announcement Delay or Repetition Timing, M-317
Change Second Recorded Announcement, M-31 6
Change Special Message 
(88), M-324
Change the Group/Supervisor of an Agent Position, M-304
Change the Source Group of a Trunk, M-31
Change the State of an Agent Position, M-304
Change the State of a CAS 
Main/ACD Trunk, M-309
Channel Memory Test, M-345
Channel Memory Testing Procedures, M-345
F=TL-I~OOOO-iooiO=TL-130100-1001M = TL-130200-1001I=TL-130300-1001D=TL-130400-1001S-TL-130500-1001A=TL-100000-1001
FeatlIESOperationMaintenanceInstallationData BaseSystem Configuration ADMP Users Guide 
						

							 rTL-130200-1001
Channel Unit Removal, M-177
Connection Between Files, M-21 9
Connection to a TCR, M-218
Current Collection Parameter Settings, M-91DDisplay Command, M-50
Downloading Featurephones, M-63
Downloading VCIP, DVCIP., and VPLC Cards, M-65
Downloading, ADMP, UCB (DCP), and NIC Card, M-66
Disk Backup of Room Status, M-83
Data Switch Device Status Display, M-99
Disk Backup Option, M-101
Device Catalog Display Option, M-102
Dedicated Time Slot, M-218
Digit Store, M-230
Data System Administrative and Maintenance Features, M-248
Data System Troubleshooting, M-250
Display Software Version Command, M-254
Display All FADS Options, M-296
Delete a CAS 
Main/ACD, M-306
Display/change FADS Delay Timing, M-306
Display Trunks by Trunk Number, M-307
Display CAS 
MainiACD Trunks by Agent Group Number, M-308
Display 
R/A Trunk Number and State, M-313
Display a Repertory Dial key Set, M-319
Day/Night Mode Data Menu, M-320
Display Day/Night Mode 
(86), M-321
Disk Device Tests, M-349
Disk Device Testing Procedures, M-349
Display Trunks with a Specific Source Group, M-309
EEvent Reports, M-249
F=TL-130000-1001O=TL-130100-1001M=TL-130200-1001I =TL-130300-1001D=TL-130400-1001S=TL-130500-1001A=TL-100000-1001Features
OperationMaintenanceInstallationData BaseSystem 
ConfiguratIon ADMP Users Guide 
						

							TL-130200-1001
FADS, CAS Main/ACD Transactions, M-285F
FADS Control Transactions, M-296
FADS Control Data Menu, M-295
FADS Display Options Menu, M-287
FADS Display Transactions, M-288
FADS Recent Chang, M-287
Fast Test Option, M-341
Fault Code Procedures and 
F!owcharts, M-155
Fault 
CorrectionM -349, M-355, M-361, M-364
Fault Isolation, M-l 55
Fault Log Request Commands, M-24
Fault Resolution, M-277
Featurephones, M-57
Featurephones 
(PD-200) M-255
Featurephone Self-Test Diagnostics, M-l 62
Force Download, M-61
Force In Service Out of Service Command, M-57, M-255
Frame Image, M-15
3GENERAL, M-l
General Read and Data General Read Commands, M-73
General Write Command, M-77
Handling Cards, M-20
Hardware Write Command, M-79
nitiate a Trend Report, M-298
Line Cards with Featurephones, M-59
F=TL-130000-1001O=TL-130100-1001hl=TL-130200-1001I=TL-130300-1001D=TL-130400-1001S=TL-130500-1001A=TL-100000-1001
Features
OperationMaintenance
InstallationData BaseSystem Configuration ADMP UsersGuide 
						

							TL-130400-1001Line/Trunk Test, M-361
Line/Trunk Test Testing Procedures, M-362
Load Commands, M-258
Load Command Responses, M-261
Loading the Program, M-338
Maintenance Command,M -55
MAINTENANCE COMMANDS AND DISPLAYS, M-23, M-249
Manual Changes and Recent Change Summary (Voice Configuration), M-324
Maintenance Displays, M-23
Maintenance Options, M-67
Maintenance Request Command, M-79Maintenance Terminals, M-l 3
Maintenance Tools, M-263Manual Hardware Testing, M-l 5
Manual Testing, M-339
Manual Testing Procedures, M-366
Mass Storage Utility Menu, M-100
Memory Access Commands, M-73
Memory Dumps, M-216
Memory Dump Contents, M-216Memory Test Results, M-97
Memory Watch Command, M-68
Network Test, M-90
Network Test, M-347
Network Testing Procedures, M-347N
Night Destination of All Agent Groups, M-303
F=TL-130000-1001O=TL-130100-1001M=TL-130200-1001I=TL-130300-1001D=TL-130400-1001S=TL-130500-1001A=TL-100000-1001
Features
OperationMaintenance
InstallationData BaseSystem Configuration ADMP Users Guide 
						

							TL-I 30400-l 001
OFF-LINE DIAGNOSTICS, M-337
ON-LINE MAINTENANCE. M-85
Packet Line Cards Status, M-99
Paging Card Test, M-346
Paging Card Testing Procedures, M-346
PD-200 Data-System Devices, M-253
PD-200 MAINTENANCE, M-247
PD-200 Maintenance Tools and Fault Isolation, M-263
Physical Locations, M-337
Power Restrictions, M-20
Preventive Maintenance, M-l 07
PUT Command Entry, M-69
Quick Reference Chart, M-107
Reference Documents, M-l 5
Return to Maintenance Options, M-96
Remote Processors Status, M-l 00
1 RECENT CHANGE, M-28
Real-Time Agent Status Display, M-288
Real-Time System Status Display, M-289
Retest Option, M-341
Repeat FMS Test, M-350
Return to Main Menu, M-354
sSecurity Codes, M-14
Security Levels, M-l 3
Self-Testing Diagnostics, M-l 4
F=TL-130000-1001O=TL-130100-1001hl=TL-130200-1001I=TL.130300-1001D=TL-130400-1001S-TL-130500-1001A=TL-100000-1001Features
OperationMaintenanceInstallation
Data BaseSystemConfiguration ADMPUsers Guide 
						

							i’TL-130400-1001
Send a Special Message (49), M-322
Send a Unique Message 
(97) M-323
Serial Device Controller Test, M-354
Serial Device Controller Testing Procedures, M-355
Software Identity Calculations (Lines), M-28
Source Message Display, M-31 1
Special Message Display 
(84) M-323
Spare Cards, M-107
Super&or Message Handler, M-321
Supervisor Message Options Menu 
(85), M-322
System Configuration, M-l 5
System Diagnostics, 
M-l 4
SYSTEM MAINTENANCE GENERAL PRINCIPLES, M-107
System Memory Test, M-341
System Memory Testing Procedures, M-343
System Operation Checks, M-107
System Software and Maintenance Applications, M-l 3
System Status, M-23
System Status Display, M-88
System Status Report, M-289
System Voltage Checks, M-107
Test Command (Featurephone), M-72
Test Device #0, M-351
Test Device 
#2, M-353
Testing, M-l 79
Test Options Menu, M-337
Test Results, M-344, M-346, M-347, M-356,M -360, M-363
Three-Party Connection, M-21 7
Tone Test, M-355
Tone Test Testing Procedures, M-356
Touch Call Receiver Status, M-96
Touch Call Receiver Test, M-89
F =TL-130000-1001Cl=TL-130100-1001M=TL-130200-1001I=TL-130300-1001D=TL-130400-1001S-TL-130500-1001A=TL-100000-1001FeaturesOperationMaintenanceInstallation
Data saw.2System Configuration ADMP Users Guide 
						

							TL-130400-1001
Touch Calling Receiver Test, M-365
Traffic Data Menu Options Menu, M-91
Traffic Meters Menu, M-92
TROUBLESHOOTING, M-155
Trunks, M-59, M-256
Trunk Sequence State Display, M-98Tl -Type Trunk Maintenance, M-l 76
Tl Trunk Trouble, M-180
TTY Response Log Display, M-36
Two-Party Connection, M-21 7
Typical Recent Change Sequences, M-333
IJUnlock Command, M-73
F=TL-130000-1001O=TL-130100-1001M =TL-130200-1001I =TL-130300-1001D=TL-130400-1001S=TL-130500-1001A=TL-100000-1001
Fe.dWSOperationMaintenanceInstallationData BaseSystem Configuration ADMP Users Guide