Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

							Installation Forms dTABLE 3-37
FORM 29 
- DTE PROFILE
SHEET 
_ OF _
21(Note 4)
22(Note 4)
23(Note 4)
24(Note 4)
25(Note 4)
Notes: 1. The DTE Profile number provides 25 programmable profiles.
2.Enter the profile number and the number of users for each profile.3. The comments field stores additional information. It is not used by the system and can
have a maximum of 20 characters.
4. The number of data sets assigned is automatically displayed by the system.Page 65 
						

							SECTION MITL9109-094-206-NATABLE 3-38
FORM 
29X - DTE PROFILE OPTIONS
SHEET 
_ OF _DTE OPTIONSPROFILE NUMBER 1 
- 25
-1 -2 -3 -4 -5 -6 -7 -6 -9 -0Terminal Type
(Enter Video Term or Teleprinter)
Language(English or French)
DTRX Echoplex(Enabled or Disabled)
DTRX Editing
(Enabled or Disabled)
DTRX Editing Delete Character
(0 - 127, decimal value of ASCII code)
DTRX Editing Display Line
(0 * 127, decimal value of ASCII code)
Inject 
< LF> after 
(ALWAYS, NEVER)
Number of pads after 
< CR>
(0 - 7)Number of pads after 
< LF >
(0 - 7)DTRX Inactivity Timer
1 
- 60 seconds
Notes: 1. x This form is nested and can only be accessed from Form 29 (DTE Profile).
2. Specify the options selected for each profile.Page 66 
						

							Installation Forms
TABLE 3-39
FORM 30 - DEVICE INTERCONNECTION TABLE
Notes: 1.
2.
3.Specify all inhibited connections with an X (indicated by a period on the CRT). Device
interconnection is inhibited unidirectionally. An X in row 6 column 1 prevents device 6from communicating with device 1. However, device 1 can still communicate with
device 6.Default is set so the system allows interconnection of Station/Sets and Consoles only.
(Permitted interconnections are indicated by an asterisk on the CRT).
Device 07 to 25 are reserved for future use.Page 67 
						

							SECTION MITL9109-094-206-NATABLE 3-40
FORM 31
- SYSTEM ABBREVIATED DIAL ENTRY
SHEET 
_ OF _Notes: 1. Specify the Index Number; a maximum of three digits.
2. Specify the Digit String; a maximum of 26 digits (25 if private).
3. Specify which entries are Private (Y) or Non-Private (N).Page 68 
						

							Installation Forms
TABLE 3-41
FORM 33 - ACCOUNT CODE ENTRY
SHEET 
_OF _Notes: 1. Specify the Account Code number. System Option 04, Account Code Length is set to
VARIABLE or a fixed value from 4 to 12 digits. System Options, Verified Account Code
must be enabled.
2. If desired, specify the COS and COR numbers. Otherwise, the caller’s COS and COR will
be applied.3. Account Codes are marked “Active” in the ACTIVE field when entered. Specify Account
Codes which are denied access with “Inactive” in the ACTIVE field.Page 
69 
						

							SECTION MITL9109-094-206-NATABLE 3-42
FORM 34 
- DIRECTED IOSHEET 
_ OF _
Notes: 1. Specify Printer Port or the extension number of a DATASET in the EXT NUM field.
2.List the data outputs in the Printout field (i.e., SMDR, Hotel/Motel), etc.
3. List the Printout Type (i.e., autoprint, monitor, directed). The choices available depend on
the option chosen in the Printout field. Monitor is available for Maintenance Logs only.Autoprint is the only option for SMDR, Hotel/Motel Wake-up or PMS. Directed is the
only option for CDE Data Print or Hotel/Motel Audit.
4.Specify whether the printout is guaranteed or not (will print or not).
Page 70 
						

							Installation Forms
TABLE 3-43
FORM 36 - MODEM ASSIGNMENT
SHEET 
_ OF _Notes: 1. A Pooled Modem consists of a Modem and a 
DATASET.2. Specify the location of each Pooled Modem’s modem component in the leftmost
BAY/SLT/CCT columns.
3. Specify the Circuit Descriptor Number for each Pooled Modem’s 
DATASET component in
the CDN column. Circuit Descriptors are defined in Form 11, Data Circuit Descriptors.4. Specify the location of each Pooled Modem’s 
DATASET component in the second set of
BAY/SLT/CCT columns.
5. Specify each Pooled Modem’s extension number in the EXTN column.
6. Specify the tenant assignment of each Pooled Modem in the TEN column.7. Optionally, specify Data Terminal Equipment (DTE) Profile numbers for Pooled Modems
in the DTE column. A DTE Profile is required for Pooled Modems serving incoming calls
that use a DTRX. DTE Profiles are defined in Form 29, DTE Profile.
8. Specify each Pooled Modem’s Class of Service in the COS column.
9. Specify each Pooled Modem’s Class of Restriction in the COR column.
10. For each Pooled Modem, specify ANSWER, ORIGINATE or BOTH in the MODE column.11. For each Pooled Modem, specify AUTO (autodial) or NON (non-autodial) in the DIAL
column.
12. The COMMENTS field stores up to 15 characters.Page 71 
						

							SECTION MITL9109-094-206-NATABLE 3-44
FORM 37 
- GUEST ROOM SUPERSET KEYS TEMPLATE
TEMPLATE 1
I IKEYSPEED DIAL NUMBERIPRIVATE
05
06
07
08
09
I I10
1112
KEY02
03
04
05
06
07
08
09
10
1112TYPETEMPLATE 2
SPEED DIAL NUMBERPRIVATE
Page 72 
						

							Installation Forms
TABLE 3-44 (CONT’D)
FORM 37 - GUEST ROOM SUPERSET KEYS TEMPLATE
TEMPLATE 3
Notes: 1. Guest Room 
SUPERSET Keys Templates apply to the SUPERSET 3DN and SUPERSET 4DN
telephones.
2.For each key in the TYPE column, specify “SPEED DIAL” or one of the following features:
AUTO ANSWER
CALL FORWARDDO NOT DISTURB
CALL PICKUP
PRIVACY RELEASENIGHT ANSWER
OVERRIDECALLBACK
PAGINGSWAP
CAMPONCALL/All-N
MUSICDATA DISCONNECT
3. For each key 
labled “SPEED DIAL”, specify the Speed Dial number in the SPEED DIAL
NUMBER column.
4. If a Speed Dial number is not to be displayed on sets or SMDR printouts, specify
“private” in the PRIVATE column.
Page 73 
						

							SECTION MITL9109-094-206-NATABLE 3-45
FORM 38 
- ACD KEYS TEMPLATE
AGENT TEMPLATE 1
AGENT TEMPLATE 2
10
1112
13
14
15
Page 74