Home
>
Panasonic
>
Communications System
>
Panasonic Digital Business System 576 Technical Manual Section 400 Programming
Panasonic Digital Business System 576 Technical Manual Section 400 Programming
Have a look at the manual Panasonic Digital Business System 576 Technical Manual Section 400 Programming online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Section 400-Programming FF2: Trunk Programming (Analog E&M Tie)
576-13-400 DBS 576 (USA) issued 05/20/98
l Page 2-43
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
Notes:
This address applies to the entry of account codes, selection of voice menu options, etc. during a call.
Up to 3 different DTMF patterns can be defined in
FF1 1 01 (0016-0019).
(all CPCs - Version 1.3 and higher) During a 3-Party Conference, if an extension dials digit(s), DTMF
signals will be sent to the other party (mainly for Voice Mail connection).
Related Programming:
DTMF ON: Pattern #1 (pg. 1-123) FF1 1 01 0016 Hold (1-255) Hold
DTMF OFF: Pattern #1 (pg. 1-124) FF1 1 01 0017 Hold (1-255) Hold
DTMF ON/OFF: Pattern #2 (pg. 1-125) FF1 1 01 0018 Hold (1-255) Hold
DTMF ON/OFF: Pattern #3 (pg. 1-126) FF1 1 01 0019 Hold (1-255) Hold
Notes:
Up to 3 different DTMF patterns can be defined in
FF1 1 01 (0016-0019).
Related Programming:
DTMF ON: Pattern #1 (pg. 1-123) FF1 1 01 0016 Hold (1-255) Hold
DTMF On/Off Pattern During Talk
(all CPCs) - Version 1.0 or higher
Set the DTMF signaling pattern that will apply after the extension user
connects to the called party during a CO call on the E&M tie trunk.
FF2 0 BSSC 01 13 Hold (0-2) Hold
0=DTMF Pattern #1BSSC: E&M Tie Trunk Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
C=Circuit no. 1-4
1=DTMF Pattern #2 (default)
2=DTMF Pattern #3
$
%2 $%) %,4
DTMF On/Off Pattern for Outgoing Dialing
(all CPCs) - Version 1.0 or higher
Set the DTMF signaling pattern that will apply to the dialing of outbound
phone numbers (DTMF sent to CO) on the E&M tie trunk.
FF2 0 BSSC 01 14 Hold (0-2) Hold
0=DTMF Pattern #1 (default)BSSC: E&M Tie Trunk Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
C=Circuit no. 1-4
1=DTMF Pattern #2
2=DTMF Pattern #3
$
%2 $%) ,
FF2: Trunk Programming (Analog E&M Tie) Section 400-Programming
Page 2-44
l DBS 576 (USA) issued 05/20/98 576-13-400
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
DTMF OFF: Pattern #1 (pg. 1-124) FF1 1 01 0017 Hold (1-255) Hold
DTMF ON/OFF: Pattern #2 (pg. 1-125) FF1 1 01 0018 Hold (1-255) Hold
DTMF ON/OFF: Pattern #3 (pg. 1-126) FF1 1 01 0019 Hold (1-255) Hold
Notes:
Related Programming:
Disconnect Supervision Timer
(all CPCs) - Version 1.0 or higher
Set how long the system will wait after detecting a drop in voltage from the
CO, before recognizing it as a valid disconnect signal.
FF2 0 BSSC 01 15 Hold (0-3) Hold
0=160 ms (default)BSSC: E&M Tie Trunk Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
C=Circuit no. 1-4
1=96 ms
2=240 ms
3=800 ms
$
! %
Not Used
(all CPCs) - Version 1.0 or higher
FF2 0 BSSC 01 16 Hold
FF2 0 BSSC 01 17 Hold
$
)! B
$
% )! B
Section 400-Programming FF2: Trunk Programming (Analog E&M Tie)
576-13-400 DBS 576 (USA) issued 05/20/98
l Page 2-45
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
Notes:
Whether
Auto Answer is enabled or disabled on this trunk (see FF2 0 BSSC 01 1), the
Auto Answer
Timer will begin after the digits are outpulsed.
rIf
Auto Answer is enabled, the system will wait until the
Timer expires before opening a voice path.
rIf
Auto Answer is disabled, the system will open the voice path when either: (1) the answer signal is
received from the other end, or (2) the
Auto Answer Timer expires -- whichever occurs first.
Related Programming:
Auto Answer for Outbound Calls (pg. 2-39) FF2 0 BSSC 01 06 Hold (0 or 1) Hold
Auto Answer Timer
(all CPCs) - Version 1.0 or higher
Set how long the system will wait before opening a voice path when the user
makes an outgoing call on this trunk.
FF2 0 BSSC 01 18 Hold (0-3) Hold
0=1 second (default)BSSC: E&M Tie Trunk Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
C=Circuit no. 1-4
1=2 seconds
2=3 seconds
3=4 seconds
$
/- ! /) %
Not Used
(all CPCs) - Version 1.0 or higher
FF2 0 BSSC 01 19 Hold $
& )! B
FF2: Trunk Programming (Analog E&M Tie) Section 400-Programming
Page 2-46
l DBS 576 (USA) issued 05/20/98 576-13-400
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
Notes:
Related Programming:
Notes:
Two different Flash Patterns can be defined in
Flash Timers 1 and 2, FF1 1 01 (0001-0002).
Related Programming:
Flash Timer 1 for Trunk Line (pg. 1-115) FF1 1 01 0001 Hold (1-255) Hold
Flash Timer 2 for Trunk Line (pg. 1-116) FF1 1 01 0002 Hold (1-255) Hold
DTMF/Dial Pulse Dialing
(all CPCs) - Version 1.0 or higher
Set the E&M tie trunk’s signaling type for outbound and inbound dialing.
FF2 0 BSSC 02 00 Hold (0 or 1) Hold
0=Dial-pulse, at 10 pps
BSSC: E&M Tie Trunk Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
C=Circuit no. 1-41=DTMF (default)
$
, %6 $0$7
Flash Pattern
(all CPCs) - Version 1.0 or higher
Set which pattern will be used for flash signals to the CO on this trunk.
(see
System Timers to define Flash Patterns #1 and #2)
FF2 0 BSSC 02 01 Hold (0 or 1) Hold
0=Flash Pattern #1 (default)BSSC: E&M Tie Trunk Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
C=Circuit no. 1-41=Flash Pattern #2
$
,9 59
Section 400-Programming FF2: Trunk Programming (Analog E&M Tie)
576-13-400 DBS 576 (USA) issued 05/20/98
l Page 2-47
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
Notes:
Related Programming:
PBX Trunk Access Codes (pg. 1-92) FF1 0 08 (0001-0006) Hold FLASH (0-9999) Hold
Not Used
(all CPCs) - Version 1.0 or higher
FF2 0 BSSC 02 02 Hold
FF2 0 BSSC 02 03 Hold
$
)! B
$
)! B
Trunk Connection Type (CO/PBX)
(all CPCs) - Version 1.0 or higher
Set whether the E&M tie trunk connects directly to another E&M trunk
(through the CO) or is behind a PBX/Centrex.
FF2 0 BSSC 02 04 Hold (0 or 1) Hold
0=CO (E&M tie) trunk. (default)BSSC: E&M Tie Trunk Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
C=Circuit no. 1-4
1=Behind a PBX/Centrex.
$
%3 %6 #0$7:
Not Used
(all CPCs) - Version 1.0 or higher
FF2 0 BSSC 02 05 Hold $
)! B
FF2: Trunk Programming (Analog E&M Tie) Section 400-Programming
Page 2-48
l DBS 576 (USA) issued 05/20/98 576-13-400
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
Notes:
Set this address to “1” (One-Way Link) to prevent double-dialing -- making an outgoing call on the
same trunk after the called party hangs up, thus bypassing TRS restrictions.
Related Programming:
Notes:
Set to “1” (Send) if the CO doesn’t support dial tone (typical in U.K.).
Related Programming:
Trunk Signal Type (pg. 2-38) FF2 0 BSSC 01 00 Hold (0-5) Hold
DTMF After Answer (Link Control)
(all CPCs) - Version 1.0 or higher
For calls on this trunk using pushbutton (DTMF) SLT phones, set whether
DTMF signals can be sent through the system after the called party answers.
FF2 0 BSSC 02 06 Hold (0 or 1) Hold
BSSC: E&M Tie Trunk Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
C=Circuit no. 1-4
$
54 !!,
0=Two-Way Link: DTMF path open
both ways. (default)
1=One-Way Link: No DTMF signaling
after the called party answers.
CO Dial Tone Simulation
(all CPCs) - Version 1.0 or higher
Set whether the system sends a simulated CO dial tone to an extension using this trunk
(important for DID Wink-Start trunk signaling).
FF2 0 BSSC 02 07 Hold (0 or 1) Hold
0=Do not send simulated CO dial toneBSSC: E&M Tie Trunk Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
C=Circuit no. 1-4
to extension. (default)
1=Send simulated CO dial tone.
$
%
# % ! %
Section 400-Programming FF2: Trunk Programming (Analog E&M Tie)
576-13-400 DBS 576 (USA) issued 05/20/98
l Page 2-49
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
Notes:
Related Programming:
SMDR Data to Serial Port (pg. 1-88) FF1 0 06 0001 Hold (0-2) Hold
SMDR Output Format (pg. 1-93) FF1 0 09 0001 Hold (0-2) Hold
Not Used
(all CPCs) - Version 1.0 or higher
FF2 0 BSSC 02 08 Hold $
)! B
SMDR for Outbound Calls
(all CPCs) - Version 1.0 or higher
Set whether
outbound calls on the E&M tie trunk will be included in SMDR records.
FF2 0 BSSC 02 09 Hold (0 or 1) Hold
0=Do not include in SMDR.BSSC: E&M Tie Trunk Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
C=Circuit no. 1-41=Include in SMDR. (default)
$
& 2 #-6-0#-
SMDR for Inbound Calls
(all CPCs) - Version 1.0 or higher
Set whether
incoming calls on this E&M tie trunk will be included in SMDR records.
FF2 0 BSSC 02 10 Hold (0 or 1) Hold
0=Do not include in SMDR. (default)BSSC: E&M Tie Trunk Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
C=Circuit no. 1-41=Include in SMDR.
$
2 #-6-0
FF2: Trunk Programming (Analog E&M Tie) Section 400-Programming
Page 2-50
l DBS 576 (USA) issued 05/20/98 576-13-400
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
Notes:
Related Programming:
SMDR Data to Serial Port (pg. 1-88) FF1 0 06 0001 Hold (0-2) Hold
SMDR Output Format (pg. 1-93) FF1 0 09 0001 Hold (0-2) Hold
Notes:
The sending of the flash signal can also be enabled/disabled on individual extensions (see
Flash-Signal
Control on pg. 3-19).
rIf the flash signal is disabled on the trunk but enabled on the extension (or vice versa), a flash signal
will be sent when the user accesses the trunk and presses FLASH.
(all CPCs - Version 1.3 and higher) If this address is set to
0=Flash signal is sent to CO (default), it will
also apply to an FF-key programmed for the SLT Flash Send feature (765 by default). See
Dial Plans A
and B on pg. 1-155.
Related Programming:
Flash-Signal Control (pg. 3-19) FF3 0 BSSC 04 21 Hold (0 or 1) Hold
Dial Plan A: Flexible Feature Codes at Dial Tone (pg. 1-155) FF1 2 02 (0001-0056) Hold (max. 4-digit Code)
Hold
Dial Plan B: Flexible Feature Codes at Dial Tone (pg. 1-157) FF1 2 03 (0001-0056) Hold (max. 4-digit Code)
Hold
Flash Key Operation
(all CPCs) - Version 1.0 or higher
Set what happens when a digital phone user presses the FLASH, PROG or
Recall key during a call on this E&M tie trunk.
FF2 0 BSSC 02 11 Hold (0 or 1) Hold
0=Flash signal is sent to CO. (default)BSSC: E&M Tie Trunk Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
C=Circuit no. 1-4
1=Trunk is released, then user hears
internal dial tone.
$
,9 !!,
Section 400-Programming FF2: Trunk Programming (Analog E&M Tie)
576-13-400 DBS 576 (USA) issued 05/20/98
l Page 2-51
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
Notes:
Related Programming:
Call Duration Timer (Tie-Lines) (pg. 1-118) FF1 1 01 0006 Hold (1-255) Hold
DTMF/Dial Pulse Dialing (pg. 2-46) FF2 0 BSSC 02 00 Hold (0 or 1) Hold
Not Used
(all CPCs) - Version 1.0 or higher
FF2 0 BSSC 02 12 Hold
FF2 0 BSSC 02 13 Hold
FF2 0 BSSC 02 14 Hold
$
)! B
$
)! B
$
)! B
DTMF Conversion (Outbound Calls)
(all CPCs) - Version 1.0 or higher
Set whether the E&M tie trunk will switch from dial-pulse to DTMF signaling after
the called party answers an outgoing call, according to the
Call Duration Timer.
FF2 0 BSSC 02 15 Hold (0 or 1) Hold
0=Do not switch to DTMF signaling.
BSSC: E&M Tie Trunk Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
C=Circuit no. 1-4
1=Switch to DTMF signaling after the called
(outside) party answers. (default)
$
$7 !(0#-
FF2: Trunk Programming (Analog E&M Tie) Section 400-Programming
Page 2-52
l DBS 576 (USA) issued 05/20/98 576-13-400
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
Notes:
Related Programming:
DTMF/Dial Pulse Dialing (pg. 2-46) FF2 0 BSSC 02 00 Hold (0 or 1) Hold
Notes:
Indirect LCR: System will send a pre-assigned code (set in the ARS Dial Conversion Tables) when an
extension seizes the trunk to make an outgoing call. This feature is used in the U.K. for sending a
system identification PIN number to the CO.
U.S.A.: Do not enable this address for MCO access code routing (eg., dialing “9” to get an outside line).
Instead, use ARS tables (see FF6) so the system can distinguish intercom calls from outgoing calls.
DTMF Conversion (Inbound Calls)
(all CPCs) - Version 1.0 or higher
Set whether the E&M tie trunk will switch from dial-pulse to DTMF signaling
after the extension user answers an incoming call.
FF2 0 BSSC 02 16 Hold (0 or 1) Hold
0=Do not switch to DTMF signaling.BSSC: E&M Tie Trunk Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
C=Circuit no. 1-4
1=Switch to DTMF signaling after the
extension user answers. (default)
$
$7 !(0
Indirect LCR
(all CPCs) - Version 1.0 or higher
(U.K. use only) Enable/Disable the Indirect Least Cost Routing (LCR) function
on the E&M tie trunk.
FF2 0 BSSC 02 17 Hold (0 or 1) Hold
0=Disable Indirect LCR. (default) BSSC: E&M Tie Trunk Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
C=Circuit no. 1-4
1=Enable Indirect LCR.
$
%
5