Home
>
Panasonic
>
Communications System
>
Panasonic Digital Business System 576 Technical Manual Section 400 Programming
Panasonic Digital Business System 576 Technical Manual Section 400 Programming
Have a look at the manual Panasonic Digital Business System 576 Technical Manual Section 400 Programming online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Section 400-Programming FF2: Trunk Programming (T1 CO)
576-13-400 DBS 576 (USA) issued 05/20/98
l Page 2-93
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
Notes:
If
Trunk COS: Incoming Ring Tone Source (pg. 1-75) is set to “0=Use trunk’s Ring Pattern
(default),” the above Ring Pattern will apply to all incoming-call types: multiple incoming, DIL, DID,
DISA. However, if the
Ring Tone Source is set to “1=Use intercom ring tone,” the above Ring Pattern
will apply only to multiple-incoming calls.
Related Programming:
Trunk COS: Incoming Ring Tone Source (pg. 1-75) FF1 0 04 (00-15) 01 Hold (0 or 1) Hold
Trunk COS Assignment (pg. 2-114) FF2 2 BSSCC 08 Hold (1-16) Hold
Ring Type/Destination for T1/CO trunks (pg. 2-107) FF2 2 BSSCC 04 (0 thru 5) Hold...
FF4 0: FF-Keys on Digital Keyphones, SLTs, and EM/24 Units (pg. 4-7)
FF4 1: FF-Keys on DSS/72 Consoles (pg. 4-14)
Ring Pattern
(all CPCs) - Version 1.0 or higher
Set the ring pattern for incoming calls on this trunk.
FF2 2 BSSCC 02 09 Hold (0-12) Hold
Setting Values for U.K.Setting Values for U.S. and Hong Kong
0Synchronize with CO0(use Pattern 1 below)
11on/2off (default) (in seconds)11on/3off (in seconds) (default)
22on/1off22on/2off
31on/1off33on/1off
4.5on/.5off41on/1off
5.25on/2.75off5.5on/.5off
6.25on/.25off/.25on/2.25off6.5on/3.5off
7.25on/.25off/.25on/.25off/.25on/1.75off7.5on/.5off/.5on/2.5off
8.75on/.25off/.75on/1.25off8.25on/.25off/.25on/3.25off
91on/.25off/.25on/1.5off91on/.25off/.25on/2.5off
101on/.25off/.25on/.25off/.25on/1off101on/.25off/.25on/.25off/.25on/2off
111.375on/.125off/.125on/.125off/.125on/.125off111.375on/.125off/.125on/.125off/.125on/.125off
12Continuous tone12Continuous tone
BSSCC: T1 (CO) Channel Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
CC=Channel no. 01-24
$
& , $%)
FF2: Trunk Programming (T1 CO) Section 400-Programming
Page 2-94
l DBS 576 (USA) issued 05/20/98 576-13-400
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
Notes:
This address applies to the entry of account codes, selection of voice menu options, etc. during a call.
Up to 3 different DTMF patterns can be defined in
FF1 1 01 (0016-0019).
(all CPCs - Version 1.3 and higher) During a 3-Party Conference, if an extension dials digit(s), DTMF
signals will be sent to the other party (mainly for Voice Mail connection).
Related Programming:
DTMF ON: Pattern #1 (pg. 1-123) FF1 1 01 0016 Hold (1-255) Hold
DTMF OFF: Pattern #1 (pg. 1-124) FF1 1 01 0017 Hold (1-255) Hold
DTMF ON/OFF: Pattern #2 (pg. 1-125) FF1 1 01 0018 Hold (1-255) Hold
DTMF ON/OFF: Pattern #3 (pg. 1-126) FF1 1 01 0019 Hold (1-255) Hold
Notes:
Up to 3 different DTMF patterns can be defined in
FF1 1 01 (0016-0019).
DTMF On/Off Pattern During Talk
(all CPCs) - Version 1.0 or higher
Set the DTMF signaling pattern that will apply after an extension user connects
to the called party during a CO call on this T1 channel.
FF2 2 BSSCC 02 10 Hold (0-2) Hold
0=DTMF Pattern #1 BSSCC: T1 (CO) Channel Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
CC=Channel no. 01-24
1=DTMF Pattern #2 (default)
2=DTMF Pattern #3
$
%2 $%) %,4
DTMF On/Off Pattern for Outgoing Dialing
(all CPCs) - Version 1.0 or higher
Set the DTMF signaling pattern that will apply to the dialing of outbound phone
numbers (DTMF sent to CO) on this T1 channel.
FF2 2 BSSCC 02 11 Hold (0-2) Hold
0=DTMF Pattern #1 (default)BSSCC: T1 (CO) Channel Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
CC=Channel no. 01-24
1=DTMF Pattern #2
2=DTMF Pattern #3
$
%2 $%) ,
Section 400-Programming FF2: Trunk Programming (T1 CO)
576-13-400 DBS 576 (USA) issued 05/20/98
l Page 2-95
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
Related Programming:
DTMF ON: Pattern #1 (pg. 1-123) FF1 1 01 0016 Hold (1-255) Hold
DTMF OFF: Pattern #1 (pg. 1-124) FF1 1 01 0017 Hold (1-255) Hold
DTMF ON/OFF: Pattern #2 (pg. 1-125) FF1 1 01 0018 Hold (1-255) Hold
DTMF ON/OFF: Pattern #3 (pg. 1-126) FF1 1 01 0019 Hold (1-255) Hold
DTMF/Dial Pulse Dialing (pg. 2-97) FF2 2 BSSCC 03 00 Hold (0 or 1) Hold
Notes:
Related Programming:
Trunk Signal Type (pg. 2-87) FF2 2 BSSCC 02 00 Hold (0-3) Hold
Disconnect Detect (pg. 2-88) FF2 2 BSSCC 02 01 Hold (0 or 1) Hold
Disconnect Supervision Timer
(all CPCs) - Version 1.0 or higher
Set how long the system will wait after detecting a drop in voltage from the CO,
before recognizing it as a valid disconnect signal.
FF2 2 BSSCC 02 12 Hold (0-3) Hold
0=281 ms (default)
BSSCC: T1 (CO) Channel Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
CC=Channel no. 01-24
1=531 ms
2=781 ms
3=1032 ms (1.032 seconds) Loop Start / Ground Start:
0=96 ms (default)
1=144 ms
2=240 ms
3=1500 ms (1.500 seconds) DID: if Trunk Signaling type is...
$
! %
FF2: Trunk Programming (T1 CO) Section 400-Programming
Page 2-96
l DBS 576 (USA) issued 05/20/98 576-13-400
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
Notes:
While the T1 channel is guarded, it cannot be used for another call until this
Guard Timer has expired.
This setting is available only if the
Tr u n k S i g n a l Ty p e is set for “0” (Loop Start) or “1” (Ground Start);
it is not available for DID signaling types.
Related Programming:
Trunk Signal Type (pg. 2-87) FF2 2 BSSCC 02 00 Hold (0-3) Hold
Notes:
If this
Inbound Ground Detect Timer is set too short, the system may generate false ringing when Tip-
ground is not removed quickly enough at the end of the call.
Related Programming:
Trunk Signal Type (pg. 2-87) FF2 2 BSSCC 02 00 Hold (0-3) Hold
Guard Timer for Outbound Calls
(all CPCs) - Version 1.0 or higher
Set how long the system guards the T1 channel after a call is disconnected.
The purpose of guarding the trunk is to prevent “glare” (collision between an
incoming and outgoing call).
FF2 2 BSSCC 02 13 Hold (0-3) Hold
0=500 ms (.5 seconds)BSSCC: T1 (CO) Channel Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
CC=Channel no. 01-24
1=1000 ms (1 second)
2=1500 ms (1.5 seconds)
3=2000 ms (2 seconds) (default)
$
1- %
Inbound Ground Detect Timer
(all CPCs) - Version 1.0 or higher
Set how long a CO Tip-ground signal must be present on a Ground Start T1
channel, before the system recognizes it as a valid incoming call.
FF2 2 BSSCC 02 14 Hold (0-3) Hold
0=1 second (default)BSSCC: T1 (CO) Channel Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
CC=Channel no. 01-24
1=2 seconds
2=4 seconds
3=8 seconds
$
1!- %
Section 400-Programming FF2: Trunk Programming (T1 CO)
576-13-400 DBS 576 (USA) issued 05/20/98
l Page 2-97
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
Notes:
Related Programming:
Notes:
Two different Flash Patterns can be defined in
Flash Timers 1 and 2, FF1 1 01 (0001-0002).
Not Used
(all CPCs) - Version 1.0 or higher
FF2 2 BSSCC 02 15 Hold
$
)! B
DTMF/Dial Pulse Dialing
(all CPCs) - Version 1.0 or higher
Set the T1 channel’s signaling type for outbound and inbound dialing.
FF2 2 BSSCC 03 00 Hold (0 or 1) Hold
0=Dial-pulse, at 10 pps BSSCC: T1 (CO) Channel Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
CC=Channel no. 01-241=DTMF (default)
$
, %6 $0$7
Flash Pattern
(all CPCs) - Version 1.0 or higher
Set the signal pattern used for flash signals sent to the CO on the T1 channel.
(see
System Timers to define Flash Patterns #1 and #2)
FF2 2 BSSCC 03 01 Hold (0 or 1) Hold
0=Flash Pattern #1 (default)BSSCC: T1 (CO) Channel Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
CC=Channel no. 01-241=Flash Pattern #2
$
,9 59
FF2: Trunk Programming (T1 CO) Section 400-Programming
Page 2-98
l DBS 576 (USA) issued 05/20/98 576-13-400
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
Related Programming:
Flash Timer 1 for Trunk Line (pg. 1-115) FF1 1 01 0001 Hold (1-255) Hold
Flash Timer 2 for Trunk Line (pg. 1-116) FF1 1 01 0002 Hold (1-255) Hold
Notes:
Related Programming:
Notes:
Related Programming:
PBX Trunk Access Codes (pg. 1-92) FF1 0 08 (0001-0006) Hold FLASH (0-9999) Hold
Dial Tone Detection
(all CPCs) - Version 1.0 or higher
Set whether the phone system will check for CO dial tone before sending dialed
digits on this trunk.
FF2 2 BSSCC 03 02 Hold (0 or 1) Hold
0=No check (use precoded delay timer). BSSCC: T1 (CO) Channel Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
CC=Channel no. 01-24
1=Check (send digits after dial tone is
detected). (default)
$
%
Trunk Connection Type (CO/PBX)
(all CPCs) - Version 1.0 or higher
Set whether the T1 channel connects directly to the CO or is behind a PBX/Centrex.
FF2 2 BSSCC 03 03 Hold (0 or 1) Hold
0=CO trunk (default)BSSCC: T1 (CO) Channel Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
CC=Channel no. 01-24
1=PBX trunk
$
%3 %6 #0$7:
Section 400-Programming FF2: Trunk Programming (T1 CO)
576-13-400 DBS 576 (USA) issued 05/20/98
l Page 2-99
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
Notes:
Auto-Repeat Dial: Dial an outside call. If busy tone is received, press REDIAL to have the system
automatically redial the number at set intervals (max. 15 times) until the called party answers or the user
hangs up.
Related Programming:
Flash Timer for Auto-Repeat Dial (pg. 1-117) FF1 1 01 0003 Hold (1-255) Hold
Notes:
Set this address to “1” (One-Way Link) to prevent double-dialing -- making an outgoing call on the
same trunk after the called party hangs up, thus bypassing TRS restrictions.
Related Programming:
DTMF/Dial Pulse Dialing (pg. 2-97) FF2 2 BSSCC 03 00 Hold (0 or 1) Hold
Auto-Repeat Dial
(all CPCs) - Version 1.0 or higher
Enable/Disable Auto-Repeat Dialing on the T1 channel.
FF2 2 BSSCC 03 04 Hold (0 or 1) Hold
0=Do not allow Auto-Repeat Dialing.BSSCC: T1 (CO) Channel Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
CC=Channel no. 01-24
1=Allow Auto-Repeat Dialing. (default)
$
/-! 6 ,
DTMF After Answer (Link Control)
(all CPCs) - Version 1.0 or higher
For calls on this T1 channel using pushbutton (DTMF) SLT phones, set whether
DTMF signals can be sent through the system after the called party answers.
FF2 2 BSSCC 03 05 Hold (0 or 1) Hold
BSSCC: T1 (CO) Channel Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
CC=Channel no. 01-24
$
54 !!,
0=Two-Way Link: DTMF path open
both ways. (default)
1=One-Way Link: No DTMF signaling
after the called party answers.
FF2: Trunk Programming (T1 CO) Section 400-Programming
Page 2-100
l DBS 576 (USA) issued 05/20/98 576-13-400
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
Notes:
Set to “1” (Send) if the CO doesn’t support dial tone (typical in U.K.).
Related Programming:
Trunk Signal Type (pg. 2-87) FF2 2 BSSCC 02 00 Hold (0-3) Hold
Notes:
Related Programming:
SMDR Data to Serial Port (pg. 1-88) FF1 0 06 0001 Hold (0-2) Hold
SMDR Output Format (pg. 1-93) FF1 0 09 0001 Hold (0-2) Hold
CO Dial Tone Simulation
(all CPCs) - Version 1.0 or higher
Set whether the system will send a simulated CO dial tone to an extension
using this T1 channel (important for DID Wink-Start trunk signaling).
FF2 2 BSSCC 03 06 Hold (0 or 1) Hold
r
0=Do not send simulated CO dial toneBSSCC: T1 (CO) Channel Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
CC=Channel no. 01-24
to extension. (default)
1=Send simulated CO dial tone to extension.
$
# %
SMDR for Outbound Calls
(all CPCs) - Version 1.0 or higher
Set whether
outbound calls on the T1 channel will be included in SMDR records.
FF2 2 BSSCC 03 07 Hold (0 or 1) Hold
0=Do not include in SMDR. BSSCC: T1 (CO) Channel Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
CC=Channel no. 01-241=Include in SMDR. (default)
$
% 2 #-6-0#-
Section 400-Programming FF2: Trunk Programming (T1 CO)
576-13-400 DBS 576 (USA) issued 05/20/98
l Page 2-101
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
Notes:
Related Programming:
SMDR Data to Serial Port (pg. 1-88) FF1 0 06 0001 Hold (0-2) Hold
SMDR Output Format (pg. 1-93) FF1 0 09 0001 Hold (0-2) Hold
Notes:
The sending of the flash signal can also be enabled/disabled on individual extensions (see
Flash-Signal
Control on pg. 3-19).
rIf the flash signal is disabled on the trunk but enabled on the extension (or vice versa), a flash signal
will be sent when the user accesses the trunk and presses FLASH.
(all CPCs - Version 1.3 and higher) If this address is set to
0=Flash signal is sent to CO (default), it will
also apply to an FF-key programmed for the SLT Flash Send feature (765 by default). See
Dial Plans A
and B on pg. 1-155.
SMDR for Inbound Calls
(all CPCs) - Version 1.0 or higher
Set whether
incoming calls on the T1 channel will be included in SMDR records.
FF2 2 BSSCC 03 08 Hold (0 or 1) Hold
0=Do not include in SMDR. (default) BSSCC: T1 (CO) Channel Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
CC=Channel no. 01-241=Include in SMDR.
$
2 #-6-0
Flash Key Operation
(all CPCs) - Version 1.0 or higher
Set what happens when a digital phone user presses the FLASH, PROG or
Recall key during a call on this T1 channel.
FF2 2 BSSCC 03 09 Hold (0 or 1) Hold
0=Flash signal is sent to CO. (default) BSSCC: T1 (CO) Channel Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
CC=Channel no. 01-24
1=T1 channel is released, then user hears
internal dial tone.
$
&
,9 !!,
FF2: Trunk Programming (T1 CO) Section 400-Programming
Page 2-102
l DBS 576 (USA) issued 05/20/98 576-13-400
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0 System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
Related Programming:
Flash-Signal Control (pg. 3-19) FF3 0 BSSC 04 21 Hold (0 or 1) Hold
Dial Plan A: Flexible Feature Codes at Dial Tone (pg. 1-155) FF1 2 02 (0001-0056) Hold (max. 4-digit Code)
Hold
Dial Plan B: Flexible Feature Codes at Dial Tone (pg. 1-157) FF1 2 03 (0001-0056) Hold (max. 4-digit Code)
Hold
Notes:
By default, individual extensions are enabled for the Long Talk Alarm (via Extension COS setting).
Related Programming:
Long Talk Alarm #1 Timer (pg. 1-134) FF1 1 02 0010 Hold (0-255) Hold
Long Talk Alarm #2 Timer (pg. 1-135) FF1 1 02 0011 Hold (0-255) Hold
Extension COS: Long Talk Alarm (pg. 1-66) FF1 0 03 (00-15) 40 Hold (0 or 1) Hold
Long Talk Alarm
(all CPCs) - Version 1.0 or higher
Enable/Disable alarm tone heard by extension user during an outbound call
on the T1 channel, if the call lasts longer than the
Long Talk Alarm Timer.
FF2 2 BSSCC 03 10 Hold (0 or 1) Hold
0=Disable Long Talk Alarm. (default) BSSCC: T1 (CO) Channel Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
CC=Channel no. 01-241=Enable Long Talk Alarm.
$
5! %,4 /,
Alarm Ringing
(all CPCs) - Version 1.0 or higher
Enable/Disable Alarm Ringing for incoming calls on this T1 channel that
ring unanswered for longer than the
Slide Ring/Alarm Ring Timer.
FF2 2 BSSCC 03 11 Hold (0 or 1) Hold
0=Disable Alarm Ringing. (default) BSSCC: T1 (CO) Channel Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
CC=Channel no. 01-24
1=Enable Alarm Ringing.
$
/,