Panasonic Digital Business System 576 Technical Manual Section 400 Programming

							Section 400-Programming FF2: Trunk Programming (ISDN)
576-13-400 DBS 576 (USA) issued 05/20/98
     l     Page 2-83
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix  A
Appe ndix  B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
Notes:
This Trunk COS Assignment controls the ring tone for incoming calls on this trunk - CO ring tone, 
intercom ring tone, or (for DIL trunks) a specific ring pattern.  The Trunk COS also controls various 
network settings.  See FF1 0 04: Trunk COS Definitions (pg. 1-75). 
Related Programming:
Trunk COS: Incoming Ring Tone Source (pg. 1-75)     FF1 0 04 (00-15) 01 Hold (0 or 1) Hold
Trunk COS: DID/DNIS Table (pg. 1-77)     FF1 0 04 (00-15) 04 Hold (0 or 1) Hold
Trunk COS: Paging on DISA/Tie-Line Call (pg. 1-78)     FF1 0 04 (00-15) 05 Hold (0 or 1) Hold
Trunk COS: DISA ID Verification (pg. 1-79)     FF1 0 04 (00-15) 06 Hold (0 or 1) Hold
Ring Pattern (pg. 2-63)     FF2 1 BSSC 02 02 Hold (0-12) Hold
Day1/Day2/Night Ring Type/Destination (pg. 2-75)     FF2 1 BSSC 04 (0 thru 5) ...
        
Notes:
This Calling Number Area Code will be sent to the CO for outbound calls on the ISDN trunk, along 
with other Calling Number digits (if assigned) in the following sequence:

 	

 
 
  
 	

  
  	

 	

Related Programming:
Calling Number Send (pg. 2-72)     FF2 1 BSSC 03 12 Hold (0 or 1) Hold
Calling Number Area Code
(all CPCs) - Version 1.0 or higher
Assign a Calling Number Area Code to the ISDN trunk.
FF2   1   BSSC    09   0   Hold   (up to 6 digits)   Hold
 
 
Calling Number Area Code
default:  [no assignment] BSSC: ISDN Trunk Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
C=Circuit no. 1-4 (BRI)
     or 1 (PRI)(max. 6 digits)
  $
&
 	/ ! 
						

							FF2: Trunk Programming (ISDN) Section 400-Programming
Page 2-84
     l     DBS 576 (USA) issued 05/20/98 576-13-400
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix  A
Appe ndix  B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
        
Notes:
This 
Calling Number Office Code will be sent to the CO for outbound calls on the ISDN trunk, along 
with other Calling Number digits (if assigned) in the following sequence:

 	

 
 
  
 	

  
  	

 	

Related Programming:
Calling Number Send (pg. 2-72)     FF2 1 BSSC 03 12 Hold (0 or 1) Hold
        
Notes:
This 
Calling Number Subscriber Number will be sent to the CO for outbound calls on the ISDN 
trunk, along with other Calling Number digits (if assigned) in the following sequence:

 	

 
 
  
 	

  
  	

 	

Related Programming:
Calling Number Send (pg. 2-72)     FF2 1 BSSC 03 12 Hold (0 or 1) Hold
Calling Number Office Code
(all CPCs) - Version 1.0 or higher
Assign a Calling Number Office Code to the ISDN trunk.
FF2   1   BSSC    09   1   Hold   (up to 6 digits)   Hold
 
 
Calling Number Office Code
default:  [no assignment] BSSC: ISDN Trunk Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
C=Circuit no. 1-4 (BRI)
     or 1 (PRI)(max. 6 digits)
  $
& 	#   !
Calling Number Subscriber Number
(all CPCs) - Version 1.0 or higher
Assign a Calling Number Subscriber Number to the ISDN trunk
FF2   1   BSSC    09   2   Hold   (up to 4 digits)   Hold
 
 
Subscriber Number (max. 4 digits) .
default:  [no assignment] BSSC: ISDN Trunk Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
C=Circuit no. 1-4 (BRI)
     or 1 (PRI)
  $
& 	-88  
						

							Section 400-Programming FF2: Trunk Programming (ISDN)
576-13-400 DBS 576 (USA) issued 05/20/98
     l     Page 2-85
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix  A
Appe ndix  B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
        
Notes:
Based on this setting, you can assign automatic volume adjustments for different connection types to 
this trunk (see FF1 8 02).
Related Programming:
Digital Pad Settings for Trunk Pad Class (pg. 1-178)     FF1 8 02 (0001-0480) Hold (0-31) Hold
Trunk Digital Pad Class Assignment
(all CPCs) - Version 1.0 or higher
Assign a Digital Pad Class to the ISDN trunk
FF2   1   BSSC   10    Hold    (1-16)   Hold
 
 
BSSC: ISDN Trunk Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
C=Circuit no. 1-4 (BRI)
     or 1 (PRI)Trunk Digital Pad Class No. 1-16
default:  7
  $
 	%%-4 $/ 5 
						

							FF2: Trunk Programming (T1 CO) Section 400-Programming
Page 2-86
     l     DBS 576 (USA) issued 05/20/98 576-13-400
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix  A
Appe ndix  B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
2.  
FF2  2:  T1 Trunks (CO)  
NOTE:For T1 point-to-point private networks (trunk connections between 2 or 
more switches), go to pg. 2-116 for T1 Trunks (E&M Tie).
If the carrier is providing DID/DNIS trunks with E&M signaling, use 
these T1 Trunks (CO) settings - not the T1 E&M Tie settings.
         
Notes:
The remaining addresses in this 
T1 Trunks (CO) section will apply if the T1 trunk is set to 
1=CO 
(default) in the above address.  If 2=Private Network is selected instead (for trunk connections between 
2 or more switches), go to pg. 2-116.
The 
1=CO (default) setting should be used for DID/DNIS trunks with E&M signaling, and the 
T1 
Trunks (CO) addresses followed.  (Set the 
Ring Type for these trunks as 1=DID or DNIS.)  
Related Programming:
Ring Type/Destination for T1/CO trunks (pg. 2-107)     FF2 2 BSSCC 04 (0 thru 5) ...
Trunk Connection Type (CO/Network)
(all CPCs) - Version 1.0 or higher
Set whether the T1 channel is connected to the CO or to a private network.
FF2   2   BSSCC    00   Hold   (0-2)   Hold
 
0=[no assignment]BSSCC:  T1 Channel Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
CC=Channel no. 01-241=CO  (default)
2=Private Network
  $

 	%3 %6 #0)*% 
						

							Section 400-Programming FF2: Trunk Programming (T1 CO)
576-13-400 DBS 576 (USA) issued 05/20/98
     l     Page 2-87
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix  A
Appe ndix  B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
        
Notes:
Press the BLK-DOWN soft key instead of the last HOLD in the above address, to scroll to the next 
BSSC trunk position and assign it a trunk number (stay in same address).
Before removing a Trunk Card from a Free Slot, you must first clear the Trunk Numbers (if assigned) 
from all of the Card’s BSSC ports in this address. See pg. 0-3 for more information.
The range of trunk numbers available for assignment depends on the CPC used:
with a CPC-96: Trunk Nos. 1-96
with a CPC-288: Trunk Nos. 1-288
with a CPC-576 Trunk Nos. 1-576
Related Programming:
Trunk Numbering (pg. 1-22)     FF1 0 02 0001 Hold (0 or 1) Hold
        
Notes:
Trunk Number Assignment
(all CPCs) - Version 1.0 or higher
Assign a trunk number to each T1 channel.
FF2   2   BSSCC   01   Hold   (0-576)   Hold
 
 
Trunk Number 1-576BSSCC:  T1 (CO) Channel Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
CC=Channel no. 01-24
default:  [no assignment](0 = no trunk)
  $
 	%-4 )-8
(or BLK-DOWN)
Trunk Signal Type
(all CPCs) - Version 1.0 or higher
Set the T1 channel’s signaling type.
FF2   2   BSSCC    02   00   Hold   (0-3)   Hold
 
0=Loop StartBSSCC:  T1 (CO) Channel Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
CC=Channel no. 01-241=Ground Start
2=DID Immediate Start
3=DID Wink Start  (default)
  $


	, 
						

							FF2: Trunk Programming (T1 CO) Section 400-Programming
Page 2-88
     l     DBS 576 (USA) issued 05/20/98 576-13-400
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix  A
Appe ndix  B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
Related Programming:
Disconnect Detect (pg. 2-88)     FF2 2 BSSCC 02 01 Hold (0 or 1) Hold
Dial Pulse Minimum Pause (pg. 2-88)     FF2 2 BSSCC 02 02 Hold (0 or 1) Hold
Ground Start Ring Type (pg. 2-89)     FF2 2 BSSCC 02 03 Hold (0 or 1) Hold
DID Ring Detect Timer (pg. 2-89)     FF2 2 BSSCC 02 04 Hold (0 or 1) Hold
Disconnect Supervision Timer (pg. 2-95)     FF2 2 BSSCC 02 12 Hold (0-3) Hold
Guard Timer for Outbound Calls (pg. 2-96)     FF2 2 BSSCC 02 13 Hold (0-3) Hold
Inbound Ground Detect Timer (pg. 2-96)     FF2 2 BSSCC 02 14 Hold (0-3) Hold
        
Notes:
This setting is available only if the 
Tr u n k  S i g n a l  Ty p e is set for “0” (Loop Start) or “1” (Ground Start); 
it is not available for DID signaling types.
Related Programming:
Trunk Signal Type (pg. 2-87)     FF2 2 BSSCC 02 00 Hold (0-3) Hold
Disconnect Supervision Timer (pg. 2-95)     FF2 2 BSSCC 02 12 Hold (0-3) Hold
        
Disconnect Detect
(all CPCs) - Version 1.0 or higher
Enable/Disable system detection of disconnect signal sent by the CO if the 
outside party disconnects first.
FF2   2   BSSCC    02   01   Hold   (0 or 1)   Hold 
 
0=No detection of disconnect signalBSSCC:  T1 (CO) Channel Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
CC=Channel no. 01-24
    from CO.  (default)
1=System will detect disconnect signal.
  $

	
 
Dial Pulse Minimum Pause
(all CPCs) - Version 1.0 or higher
Set the minimum pause time for dial-pulse signaling.
FF2   2   BSSCC    02   02   Hold   (0 or 1)   Hold
 
 
0=625 ms  (default-US)  orBSSCC:  T1 (CO) Channel Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
CC=Channel no. 01-24
    750 ms  (default-UK)
1=1000 ms
  $

	
$ 2)@$- 
						

							Section 400-Programming FF2: Trunk Programming (T1 CO)
576-13-400 DBS 576 (USA) issued 05/20/98
     l     Page 2-89
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix  A
Appe ndix  B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
Notes:
This setting is available only if the Tr u n k  S i g n a l  Ty p e is set for “0” (Loop Start) or “1” (Ground Start); 
it is not available for DID signaling types.
Related Programming:
Trunk Signal Type (pg. 2-87)     FF2 2 BSSCC 02 00 Hold (0-3) Hold
        
Notes:
This setting is available only if the Trunk Signal Type is set for “1” (Ground Start); it is not available 
for Loop Start or DID signaling types.  (Ground Start trunks typically need Tip-side ground for 
incoming signal.)
Related Programming:
Trunk Signal Type (pg. 2-87)     FF2 2 BSSCC 02 00 Hold (0-3) Hold
        
Ground Start Ring Type
(all CPCs) - Version 1.0 or higher
Set whether the CO supplies the real ringing signal or not. Applies to Ground-
Start trunks, which typically need Tip-Ground for incoming signal.
FF2   2   BSSCC    02   03   Hold   (0 or 1)   Hold 
 
0=CO ringing signal.  (default) BSSCC:  T1 (CO) Channel Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
CC=Channel no. 01-24
1=No CO ringing signal.
  $

	
1  %6
DID Ring Detect Timer
(all CPCs) - Version 1.0 or higher
Set the timer for detecting DID ringing, which will be used to specify the ringing.
FF2   2   BSSCC    02   04   Hold   (0 or 1)   Hold
 
0=32 ms  (default)BSSCC:  T1 (CO) Channel Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
CC=Channel no. 01-241=96 ms
  $

	
 *% % 
						

							FF2: Trunk Programming (T1 CO) Section 400-Programming
Page 2-90
     l     DBS 576 (USA) issued 05/20/98 576-13-400
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix  A
Appe ndix  B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
Notes:
If CO is set to Immediate Start, system will wait this long before recognizing ring from CO.
This setting is available only if the Trunk Signal Type is set for “2” (DID Immediate Start) or “3” (DID 
Wink Start); it is not available for Loop Start or Ground Start signaling types.
Related Programming:
Trunk Signal Type (pg. 2-87)     FF2 2 BSSCC 02 00 Hold (0-3) Hold
      
        
Notes:
This setting is available only for Channel 01.
“SF” stands for SuperFrame (also known as D4), in which sampling frames are transmitted in groups of 
12.
“ESF” stands for Extended SuperFrame, in which sampling frames are transmitted in groups of 24.  ESF 
provides monitoring and maintenance capabilities that aren’t available with SF.
Both “SF” and “ESF” use robbed-bit signaling, in which the 8th bit is robbed from every 6th frame to 
transmit signaling states such as On-Hook and Off-Hook.
Not Used
(all CPCs) - Version 1.0 or higher
FF2   2   BSSCC    02   05   Hold
 
  $


	)! B
Frame Format
(all CPCs) - Version 1.0 or higher
Set the framing format ordered from the CO (assign to Channel #1).
FF2   2   BSSCC    02   06   Hold   (0 or 1)   Hold
 
 
0=SF  (default)BSSCC:  T1 (CO) Channel Position (“01” only)
B=Cabinet no. 1-6
SS=Slot no. 01-12
CC=Channel no. 01
1=ESF
  $

	
 ! 
						

							Section 400-Programming FF2: Trunk Programming (T1 CO)
576-13-400 DBS 576 (USA) issued 05/20/98
     l     Page 2-91
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix  A
Appe ndix  B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
Related Programming:
Synchronized Clock (pg. 1-103)     FF1 0 18 (0001-0003) Hold (BSS/C) Hold
          
Notes:
This setting is available only for Channel 01.
“AMI” stands for Alternate Mark Inversion.
“B8ZS” stands for Binary 8-Zeros Suppression.
Related Programming:
Line Coding
(all CPCs) - Version 1.0 or higher
Set the clear-channel format ordered from the CO (assign to Channel #1).
FF2   2   BSSCC    02   07   Hold   (0 or 1)   Hold
 
 
0=AMI  (default)BSSCC:  T1 (CO) Channel Position (“01” only)
B=Cabinet no. 1-6
SS=Slot no. 01-12
CC=Channel no. 011=B8ZS
  $

%	
5 ! 
						

							FF2: Trunk Programming (T1 CO) Section 400-Programming
Page 2-92
     l     DBS 576 (USA) issued 05/20/98 576-13-400
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appl ications
FF8Maintenance Introduction
Appe ndix  A
Appe ndix  B
FF1System
FF2Tr u n k s
FF3Extensions
FF4FF-/Soft Keys
FF5Groups
FF6TRS/ARS
0   System
Configuration
FF7Appli cations
FF8Maintenance Introduction
Appe ndix A
Appe ndix B
         
Notes:
Related Programming:
Ring Frequency
(all CPCs) - Version 1.0 or higher
Set the ring frequency for incoming calls on the T1 channel.  Affects ringing 
pitch on digital phones.
FF2   2   BSSCC    02   08   Hold   (0-6)   Hold 
 
1=400/562 Hz  (default)
BSSCC:  T1 (CO) Channel Position
B=Cabinet no. 1-6
SS=Slot no. 01-12
CC=Channel no. 01-242=1000/1340 Hz
3=400 Hz
4=800/1040 Hz
5=1040/1320 Hz
6=660/1320 Hz 0=No Ring
  $

	 F-