Ricoh Mp C3000 Service Manual

							Fax Communication Features 
SM 139 B786 
B786 
Fax Option 
indicate E, even if subsequent communications were OK. 
If two of the communications had an error, the Journal will indi cate the destination 
for the first error only. 
Report Sample 
  
						

							IP-Fax 
B786 140  SM 
5.5 IP-FAX 
5.5.1  WHAT IS IP-FAX? 
For details: Core Technology Manual – Facsimile Processes – Faxing from a PC – 
Internet/LAN Fax Boards – IP-FAX 
T.38 Packet Format 
TCP is selected by default for this machine, but you can change this to UDP with IPFAX 
SW 00 Bit 1. 
UDP Related Switches 
 
IP-Fax Switch 01 
No. FUNCTION  COMMENTS  
Select IP FAX Delay Level 
Bit3 Bit2 Bit1 Bit0  Setting 
0 0 0 0 Level 0 
0 0 0 1 Level 1 
0 0 1 0 Level 2 
0 0 1 1 Level 3 
0-3 
      Raise the level by selecting a higher setting 
if too many transmission errors are 
occurring on the network. 
If TCP/UDP is enabled on the network, raise 
this setting on the T.30 machine. Increasing 
the delay time allows the recovery of more 
lost packets. 
If only UDP is enabled, increase the number 
of redundant packets. 
Level 1~2: 3 Redundant packets 
Level 3: 4 Redundant packets 
Settings 
User parameter switch 34 (22[H]), bit 0 
IP-Fax Gate Keeper usage 0: No, 1: Yes 
IP Fax Switches: Various IP-FAX settings (see the bit switch table)  
						

							General Specifications 
SM 141 B786 
B786 
Fax Option 6. SPECIFICATIONS 
6.1 GENERAL SPECIFICATIONS 
6.1.1 FCU 
Type:  Desktop type transceiver 
Circuit: PSTN (max. 3ch.) 
PABX 
Connection: Direct 
couple 
Original Size: Book (Face down) 
Maximum Length: 432 mm [17 ins] 
Maximum Width: 297 mm [11.7 ins] 
ARDF (Face up) 
(Single-sided document) 
Length: 128 - 1200 mm [5.0 - 47.2 ins] 
Width: 105 - 297 mm [4.1 - 11.7 inch] 
(Double-sided document) 
Length: 128 - 432 mm [5.0 - 17 inch] 
Width: 105 - 297 mm [4.1 - 11.7 inch] 
Max. Paper Length 
Max. paper length 600 mm (23.6”) (default), or 800 (31.5”) to 
1200 mm (47.2”) if SP5-150 is set to 1. 
NOTE
: When SP5-150 is set to 1, the actual maximum 
depends on the width of the Fax received and the page 
memory size. 
Scanning Method:  Flat bed, with CCD 
Resolution:  G3 
8 x 3.85 lines/mm (Standard) 
8 x 7.7 lines/mm (Detail) 
8 x 15.4 line/mm (Fine) See Note1 
16 x15.4 line/mm (Super Fine) See Note 1 
200 x 100 dpi (Standard) 
200 x 200 dpi (Detail) 
400 x 400 dpi (Super Fine) See Note 1 
 
1. Optional Expansion Memory required 
Transmission Time:  G3: 3 s at 28800 bps; Measured with G3 ECM using memory 
for an ITU-T #1 test document (Slerexe letter) at standard 
resolution 
Data Compression:  MH, MR, MMR, JBIG 
Protocol: 
Group 3 with ECM 
⇒ 
Rev. 03/2007  
						

							General Specifications 
B786 142  SM 
Modulation: V.34, V.33, V.17 (TCM), V.29 (QAM),  
V.27ter (PHM), V.8, V.21 (FM) 
Data Rate: G3: 33600/31200/28800/26400/24000/21600/ 
19200/16800/14400/12000/9600/7200/4800/2400 bps 
Automatic fallback 
I/O Rate: 
With ECM: 0 ms/line 
Without ECM: 2.5, 5, 10, 20, or 40 ms/line 
Memory Capacity: ECM: 128 KB 
SAF 
Standard: 4 MB 
With optional Expansion Memory: 28 MB (4 MB+ 24 MB) 
Page Memory 
Standard: 4 MB (Print: 2 MB + Scanner: 2 MB) 
With optional Expansion Memory: 12 MB (4 MB + 8 MB) 
(Print 8 MB + Scanner: 4 MB) 
 
6.1.2 CAPABILITIES OF
 PROGRAMMABLE ITEMS 
The following table shows the capab ilities of each programmable items. 
 
Item  Standard 
Quick Dial  2000 
Groups 100 
Destination per Group  500 
Destinations dialed from the ten-key pad overall  500 
Programs 100 
Auto Document  6 
Communication records for Journal stored in the 
memory 200 
Specific Senders 
30 
 
The following table shows how the capabilities of the document memory will change after 
the Expansion Memory are installed. 
 
  Without the 
Expansion Memory With the Expansion 
Memory  
Memory Transmission 
file  400 400 
Rev. 03/2007 
						

							General Specifications 
SM 143 B786 
B786 
Fax Option 
Maximum number of 
page for memory 
transmission  1000 1000 
Memory capacity for 
memory transmission 
(
 Note) 320 2240 
 
ƒ  Measured using an ITU-T #1 test docum ent (Slerexe letter) at the standard 
resolution, the auto image dens ity mode and the Text mode. 
Rev. 03/2007  
						

							IFAX Specifications 
B786 144  SM 
6.2 IFAX SPECIFICATIONS 
Connectivity: Local area network  
Ethernet 100base-Tx/10base-T 
IEEE1394 (IP over 1394) 
IEEE802.11b (wireless LAN) 
Resolution:
 Main scan: 400 dpi, 200 dpi 
Sub scan: 400 dpi, 200 dpi, 100 dpi  
ƒ  To use 400 dpi, IFAX SW01 Bit 4 must be set to “1”. 
Transmission 
Time:   1 s (through a LAN to the server) 
Condition: ITU-T #1 test document (Selerexe Letter) 
MTF correction: OFF 
TTI: None 
Resolution: 200 x 100 dpi 
Communication speed: 10 Mbps 
Correspondent device: E-mail server 
Line conditions: No terminal access 
Document Size:
 Maximum message width is A4/LT.  
ƒ  To use B4 and A3 width, IFAX SW00 Bit 1 (B4) and/or Bit 
2 (A3) must be set to “1”. 
E-mail File 
Format:  Single/multi-part 
MIME conversion 
Image: TIFF-F (MH, MR, MMR) 
Protocol:
  Transmission:
 
SMTP, TCP/IP 
Reception:  
POP3, SMTP, IMAP4, TCP/IP 
Data Rate:  100 Mbps(100base-Tx) 
10 Mbps (10base-T) 
Authentication 
Method:
  SMTP-AUTH 
POP before SMTP 
A-POP 
Remark: 
The machine must be set up as an  e-mail client before installation. 
Any client PCs connected to t he machine through a LAN must 
also be e-mail clients, or some  features will not work (e.g. 
Autorouting). 
  
						

							IP-FAX Specifications 
SM 145 B786 
B786 
Fax Option 
6.3 IP-FAX SPECIFICATIONS 
Network:  Local Area  Network 
Ethernet/10base-T, 100base-TX 
IEEE1394 (IP over 1394) 
IEEE802.11b (wireless LAN) 
Scan line density: 8 x 3.85 lines/mm, 200x100d
pi (standard character), 
8 x 7.7lines/mm, 200x200d pi (detail character), 
8 x 15.4lines/mm (fine characte r: optional expansion memory 
required), 
16 x 15.4lines/mm, 400x400dpi (s uper fine character: optional 
expansion memory required) 
Original size:  Maximum A3 or 11x 17 (DLT) 
Maximum scanning 
size:  Standard: A3, 297mm x 432mm 
Irregular: 297mm x 1200mm 
Transmission 
protocol: 
Recommended: T.38 Annex protocol, TCP, UDP/IP 
communication 
Compatible 
machines: 
IP-Fax compatible machines 
IP-Fax transmission 
function: Specify IP address and send fax to an IP-Fax compatible fax 
through a network. 
Also capable of sending fax fr
om a G3 fax connected to the 
public telephone lines via a VoIP gateway. 
IP-Fax reception 
function:  Receive a fax sent from an IP-Fax compatible fax through a 
network. 
Also capable of receiving fax fr
om a G3 fax connected the public 
telephone lines via a VoIP gateway. 
  
						

							Fax Unit Configuration 
B786 146  SM 
6.4  FAX UNIT CONFIGURATION 
 
 
Component Code No. Remarks 
MBU 1 
FCU 2 
FCU I/F  3 
Mother Board  4 
Speaker B786 
5 Included with fax unit 
Expansion Memory   G578  6  Optional 
CCU I/F Board 
7 
SG3 Board  B787 
8 Optional 
SG3 Board 
B787  9  Optiona 
Handset Type 1018  B433    NA only. Common with J-C2 
 
  
						

							 
ARDF DF3000 B789 
B789  ARDF DF3000 
Page Date  Added/Updated/New 
      None