Ricoh Mp C3000 Service Manual

							 
SM 5-273 B230/B237/D042 
Service 
Tables 
001 Reboot Setting  *CTL Enables or disables 
the automatic reboot 
function when an SC error occurs. 
[0 or 1/  0 / – ] 
0: The machine reboots automatically 
when the machine issues an SC error and 
logs the SC error code. If the same SC 
occurs again, the machine does not 
reboot. 
1: The machine does not reboot when an 
SC error occurs. 
The reboot is not executed for Type A or C 
SC codes. 
002 Reboot Type  *CTL Selects the reboot method for SC. 
[0 or 1 / 
0 / -] 
0: Manual reboot, 1: Automatic reboot 
 
5878   [Option Setup]  
001 Option Setup  - Enables the Data Overwrite Security unit. 
Press EXECUTE on the operation panel. 
Then turn the machine off and on. 
 
5881   [Fixed Phrase Block Erasing]  
001  -  -  Deletes the fixed phrase. 
 
[WIM Settings]  Web Image Monitor Settings 
5885 
Close or disclose the func tions of web image monitor. 
020 Document Server ACC 
Ctrl  *CTL 0: OFF, 1: ON 
Bit Meaning 
0: Forbid all document server access (1) 
1: Forbid user mode access (1) 
2: Forbid print function (1)  
						

							 
B230/B237/D042 5-274 SM 
3: Forbid fax TX (1) 
4: Forbid scan sending (1) 
5: Forbid downloading (1) 
6: Forbid delete (1) 
7: Reserved 
 
[Permit ROM Updating] DFU  
5886 
This SP determines whether  the ROM can be updated. 
001 -  *CTL   [0 or 1 / 
0 / 1/step] 
0: ON, 1: OFF 
 
[Plug & Play Maker/Model Name]  Plug & Play Name Selection 
5907  Specifies the manufacture
r and model name. These nam es are registered in 
the NVRAM. If the NVRA M becomes defective, these names should be 
re-registered. 
001 Plug/Play  *ENG[0 to 11 / 
0 / 1 /step ]  FA 
0: RICOH Aficio MP C3000 
1: RICOH Aficio MP C2500 
2: SAVIN C2525 
3: SAVIN C3030 
4: Gestetner MPC 2500/DSc525 
5: Gestetner MPC 3000/DSc530 
6: NRG MP C2500 
7: NRG MP C3000 
8: infotec ISC2525 
9: infotec ISC3030 
10: LANIER MP C2500/LD425c 
11: LANIER MP C3000/LD430c 
  
						

							 
SM 5-275 B230/B237/D042 
Service 
Tables 
5913   [Switchover Permission Time]  
Print Application Timer  *CTL 
[3 to 30 / 3 / 1 second /step] 
002  Sets the amount of time to elapse wh
ile the machine is in standby mode (and 
the operation panel keys have not bee n used) before another application can 
gain control of the display. 
 
5967   [Copy Server Set 
Function]
  *CTL 
 0 : ON, 1: OFF 
  Enables and disables the doc
ument server. This is a security measure that 
prevents image data from being left in  the temporary area of the HDD. After 
changing this setting, you must switch the main switch off and on to enable the 
new setting. 
 
[Cherry Server] 
5974 
Specifies which version of  ScanRouter, “Lite” or “Full”, is installed. 
001 Cherry Server   *CTL
    [0 or 1 / 
0 / – ] 
0: Lite 
1: Full 
 
[Device Setting]  
5985  The NIC and USB support features are built
 into the GW controller. Use this 
SP to enable and disable these features. In order to use the NIC and USB 
functions built into the controller board, these SP codes must be set to 1. 
001 
On Board NIC  [0 to 2 / 
0 / 1 /step] 
0: Disable, 1: Enable,  2: Function limitation 
When the Function limitation  is set, On board NIC is 
limited only for the NRS or  LDAP/NT authentication. 
 
ƒ   Other network applications such as 
WebImageMonitor, NRS or LDAP/NT 
Rev. 09/16/2009 
⇒  
						

							 
B230/B237/D042 5-276 SM 
authentication are not available when this SP is 
set to 2. Even though you can change the initial 
settings of those netwo rk applications, the 
settings do not work. 
002  On Board USB  [0 or 1 / 
0 / 1/step] 
0: Disable, 1: Enable 
 
5987   [Counter Falsification Prevention]   
 001  0: OFF / 1: ON This SP detects that a mechanical counter device is 
removed. If it is detected, SC610 occurs.  
ƒ   The mechanical counter is provided only for 
NA model. 
 
[SP print mode] 
5990 
Prints out the SMC sheets. 
001  All (Data List)  - 
002  SP (Mode Data List)  - 
003 User Program  -   
004 Logging Data - 
005 Diagnostic Report  -   
006 Non-Default - 
007 NIB Summary  - 
008 Capture Log -   
021  Copier User Program  -    
022 Scanner SP  -   
023  Scanner User Program  -     - 
Rev. 09/16/2009 
						

							 
SM 5-277 B230/B237/D042 
Service 
Tables 
SP6-XXX (Peripherals) 
6006   [ADF Adj.]  ADF Adjustment 
  Adjusts the side-to-side and leading re gistration of originals with the ARDF. 
001 Side-to-Side Registration 
[-3.0 to 3.0 / 0 / 0.1 mm/step ] 
003  Leading Edge 
Registration  *ENG
[-5.0 to 5.0 /  0 / 0.1 mm/step ] 
  Adjusts the amount of paper buckle to 
correct original skew for the front and 
rear sides. 
005  Buckle: Duplex Front 
006  Buckle: Duplex Rear  *ENG
[-5.0 to 5.0 /  0 / 0.1 mm/step ] 
  Adjusts the erase margin at the original trailing edge. 
007  Rear Edge Erase  *ENG
[-5.0 to 5.0 / 0 / 0.1 mm/step ] 
 
[ADF Input Check]  
6007 
Displays the signals received from t he sensors and switches of the ARDF. 
Only Bit 0 is used for ADF input check. 
001  Original Length 1 (B5 
Detection Sensor) 
002 Original Length 2 (A4 
Detection Sensor) 
003 Original Length 3 (LG 
Detection Sensor) 
004  Original Width S 
005  Original Width M 
006  Original Width L 
007  Original Width LL  0: Paper not detected 
1: Paper detected  
						

							 
B230/B237/D042 5-278 SM 
009 Original Detection 
010  Rear Edge Detection 
011 Skew Correction 
013 Registration 
014 Exit 
015 Feed Cover 0: ADF cover close 
1: ADF cover open 
016 Lift Up 0: ADF  close 
1: ADF  open 
[ADF Output Check]
 
6008 
Activates the electrical co mponents for functional check. 
It is not possible to activate more  than one component at the same time. 
003  Feed Motor Forward  Feed Motor-Forward rotation 
004  Feed Motor Reverse Feed Motor-Reverse rotation 
005  Relay Motor Forward  Transport Motor- Forward rotation 
006  Relay Motor Reverse Transport Motor- Forward rotation 
009 Feed Clutch  - 
010  Feed Solenoid    Pick-up Solenoid 
011 Inverter Solenoid - 
012 Stamp - 
Stamp Solenoid 
[ADF Free Run]  6009 
Performs a DF free run in duplex mode or stamp mode. 
002  Free Run Duplex Motion  After executing this SP mode, turn the main power
Off/On. 
 
⇒
Rev. 02/19/2009 
						

							 
SM 5-279 B230/B237/D042 
Service 
Tables 
 
[Stamp Position Adj.]  Fax Stamp Position Adjustment 
6010 
Adjusts the horizontal position of  the stamp on the scanned originals. 
6010 1  Stamp Position Adj.  *ENG
[-5.0 to 5.0 / 0 / 1 mm/step] 
 
[Original Size Detection Priority]  Original Size Detection Priority 
6016 
Specifies the original size for a size  detected by the original sensor, since 
original sensors cannot recognize all sizes. 
001  Original Size Detection 
Priority  *ENG[0 or 1 / 
0 / - ] 
0: Setting 1 
1: Setting 2 
Setting 1Setting 2 
Bit 7: A4 (L)/LT (L) 
Bit 6: 11 x 15/DLT (L) 
Bit 5: DLT (L)/ 11 x 15 
Bit 4: LT (S)/ US Exec (S) 
Bit 3: LT (L)/ 8 x 10 (L) 
Bit 2: LG (L)/ F4 (L) 
Bit 1: A4 (L)/ 16K (L) 
Bit 0: 8K (L)/ DLT (L) 
Bits used for detection differ depending on 
destination as shown below. 
Bit 7 to 6: Only for Japan 
Bit 5 to 2: Only for US 
Bit 1 to 0: Only for EU/AA 
 
[DF Magnification Adj.]  DF Magnification Adjustment 
6017 
Adjusts the magnification in the  sub-scan direction for the ARDF. 
001 DF Magnification Adj.  *CTL
[-5.0 to 5.0 / 0 / 0.1 %/step] 
 
6123   [Jogger Position Adj.]   
						

							 
B230/B237/D042 5-280 SM 
Adjusts the jogger position. 
001 - *ENG
[-4.0 to 4.0 /  0 / 0.4 mm/step] 
 
[Punch Position: Sub Scan]  
6128 
Adjusts the punching position  in the sub scan direction. 
001 Domestic 2Hole  *ENG
002 North America 3Hole  *ENG
003 Europe 4Hole  *ENG
004  North Europe 4Hole  *ENG
005  North Europe 2Hole  *ENG [-7.5 to 7.5 / 
0 / 0.5 mm/step]] 
 
[Punch Position: Main Scan]  
6129 
Adjusts the punching position in  the main scan direction. 
001 Domestic 2Hole  *ENG
002 North America 3Hole  *ENG
003 Europe 4Hole  *ENG
004  North Europe 4Hole  *ENG
005  North Europe 2Hole  *ENG [-2.0 to 2.0 / 
0 / 0.4 mm/step]] 
 
[Skew Correction: Buckle Adj.]  
6130 
Adjusts the paper buckle for each paper size. 
001 A3T (SEF)  *ENG
002 B4T (SEF) *ENG
003 A4T (SEF) *ENG[-5.0 to 5.0 / 
0 / 0.25 mm/step]]  
						

							 
SM 5-281 B230/B237/D042 
Service 
Tables 
004 A4Y (LEF)  *ENG
005 B5T (SEF) *ENG
006 B5Y (LEF)  *ENG
007 DLT-T (SEF) *ENG
008 LG-T (SEF)  *ENG
009 LT-T (SEF) *ENG
010 LT-Y (LEF)  *ENG
011  12 x 18 *ENG
012 Other  *ENG
 
[Skew Correction Control]  
6131 
Selects the skew correction control  for each paper size. These are only 
activated for B793. 
001 A3T (SEF)  *ENG
002 B4T (SEF) *ENG
003 A4T (SEF) *ENG
004 A4Y (LEF)  *ENG
005 B5T (SEF) *ENG
006 B5Y (LEF)  *ENG
007 DLT-T (SEF) *ENG
008 LG-T (SEF)  *ENG
009 LT-T (SEF) *ENG
010 LT-Y (LEF)  *ENG
011  12 x 18 *ENG[0 to 2 / 
1 / 1/step]] 
0: No (No skew correction) 
1: Roller Stop Skew Correction 
2: Roller Reverse Skew Correction  
						

							 
B230/B237/D042 5-282 SM 
012 Other *ENG
 
[Jogger Fence Fine Adj]  
6132  This SP adjusts the distance between t
he jogger fences and the sides of the 
stack on the finisher stapling tray in th e Booklet Finisher B793. The adjustment 
is done perpendicular to the direction of paper feed. 
001 A3T (SEF)  *ENG
002 B4T (SEF) *ENG
003 A4T (SEF) *ENG
004 A4Y (LEF)  *ENG
005 B5T (SEF) *ENG
006 B5Y (LEF)  *ENG
007 DLT-T (SEF) *ENG
008 LG-T (SEF)  *ENG
009 LT-T (SEF) *ENG
010 LT-Y (LEF)  *ENG
011  12 x 18 *ENG
012 Other  *ENG[-1.5 to 1.5 / 
0 / 1/step] 
+ Value: Increases distance between 
jogger fences and the sides of the stack. 
- Value: Decreases the distance between 
the jogger fences and the sides of the 
stack. 
 
[Staple Position Adjustment]  
6133  Adjusts the staple position for 
each finisher (B408/B793/B792).  
+ Value: Moves the staple position to the rear side. 
- Value: Moves the staple pos ition to the front side. 
001  Finisher 1 (B408/B793)  *ENG
[-3.5 to 3.5 / 0 / 1/step]] 
002  Finisher 2 (B792)  *ENG
[-2.0 to 2.0 / 0 / 1/step]]