Ricoh Mp C3000 Service Manual

							 
SM 5-253 B230/B237/D042 
Service 
Tables 
SP5-828-50 is set to 1. 
065 Job Spooling  Enables/disables Job Spooling. 
[0 or 1 / 
0 / 1 / step] 
0: Disabled, 1: Enabled 
066  Job Spooling Clear: 
Start  Tim e  Treatment of the job when
 a spooled job exists at 
power on. 
0: ON (Data is cleared) 
1 : OFF (Automatically printed) 
069  Job Spooling (Protocol)  Validates or invalidates 
the job spooling function 
for each protocol. 
0 : Validates 
1: Invalidates 
bit0: LPR 
bit1: FTP 
bit2: IPP 
bit3: SMB 
bit4: BMLinkS 
bit5: DIPRINT 
bit6: sftp 
bit7: (Reserved) 
090  TELNET (0: OFF 1: ON) Enables or disables 
the Telnet protocol. 
[0 or 1 /  1 / – ] 
0: Disable, 1: Enable 
091  Web (0: OFF 1: ON)  Enables or disables
 the Web operation. 
[0 or 1 /  1 / – ] 
0: Disable, 1: Enable 
145  Active IPv6 Link Local 
Address  This is the IPv6 local address link referenced on 
the Ethernet or wireless LAN (802.11b) in the 
format:  
Link Local Address + Prefix Length 
The IPv6 address consists of a total 128 bits 
configured in 8 blocks of 16 bits each.  
						

							 
B230/B237/D042 5-254 SM 
147 Active IPv6 Stateless 
Address 1 
149 Active IPv6 Stateless 
Address 2 
151 Active IPv6 Stateless 
Address 3 
153 Active IPv6 Stateless 
Address 4 
155 Active IPv6 Stateless 
Address 5  These SPs are the IPv6 status addresses (1 to 5) 
referenced on the Ethernet or wireless LAN 
(802.11b) in the format:   
Status Address + Prefix Length 
The IPv6 address consists of a total 128 bits 
configured in 8 blocks of 16 bits each. 
156 IPv6 Manual Address 
This SP is the IPv6 manually set address 
referenced on the Ethernet or wireless LAN 
(802.11b) in the format:   
Manual Set Address + Prefix Length 
The IPv6 address consists of a total 128 bits 
configured in 8 blocks of 16 bits each. 
158 IPv6 Gateway Address 
This SP is the IPv6 gateway address referenced 
on the Ethernet or wireless LAN (802.11b). The 
IPv6 address consists of a total 128 bits configured 
in 8 blocks of 16 bits each. 
 
5832   [HDD]  HDD Initialization  *CTL
- 
001  HDD Formatting (ALL)     
002  HDD Formatting (IMH) 
003  HDD Formatting 
(Thumbnail) 
004 HDD Formatting (Job 
Log) 
005  HDD Formatting (Printer  Initializes the hard disk. Use this SP mode only if 
there is a hard disk error.  
						

							 
SM 5-255 B230/B237/D042 
Service 
Tables 
Fonts) 
006  HDD Formatting (User 
Info) 
007  Mail RX Data   
008 Mail TX Data  
009 HDD Formatting (Data for 
a Design) 
010  HDD Formatting (Log) 
011 HDD Formatting (Ridoc 
I/F) 
 
5836  [Capture Settings]  *CTL - 
Capture Function (0:Off 1:On) 
0: Disable, 1: Enable 
001 
With this function disabled, the settings related to  the capture feature cannot 
be initialized, displayed, or selected. 
Panel Setting  0: Displayed, 1: Not displayed 
002 
Displays or does not display  the capture function buttons. 
 5836-71 to 5836-78, Copier and Printer Document Reduction
 
The following 6 SP modes set the default reduction for stored documents 
sent to the document managem ent server via the MLB. 
Enabled only when optional MLB (Media  Link Board) is installed. 
071  Reduction for Copy Color 
0: 1to-1, 1: 1/2, 2: 1/3, 3: 1/4 
072  Reduction for Copy B&W Text 
0: 1to-1, 1: 1/2, 2: 1/3, 3: 1/4 
073  Reduction for Copy B&W Other 
0: 1to-1, 1: 1/2, 2: 1/3, 3: 1/4 
074  Reduction for Printer Color 
0: 1to-1, 1: 1/2, 2: 1/3, 3: 1/4 
075  Reduction for Printer B&W 
0: 1to-1, 1: 1/2, 2: 1/3, 3: 1/4  
						

							 
B230/B237/D042 5-256 SM 
076  Reduction for Printer B&W HQ 
0: 1to-1, 1: 1/2, 2: 1/3, 3: 1/4 
077  Reduction for Printer Color 1200
1: 1/2, 3: 1/4, 4: 1/6, 5: 1/8 (2: skipped) 
078  Reduction for Printer B&W 1200
1: 1/2, 3: 1/4, 4: 1/6, 5: 1/8 (2: skipped) 
  5836-81 to 5836-86, Stored document format
 
The following 6 SP modes set Sets  the default format for stored documents 
sent to the document managem ent server via the MLB. 
Enabled only when optional MLB (Media  Link Board) is installed. 
081  Format for Copy Color 0: JFIF/JPEG
, 1: TIFF/MMR,   
2: TIFF/MH, 3: TIFF/MR 
 
ƒ  This SP is not used in this model. 
082  Format for Copy B&W Text  0: JFIF/JPEG, 
1: TIFF/MMR,  
2: TIFF/MH, 3: TIFF/MR 
083  Format Copy B&W Other  0: JFIF/JPEG, 
1: TIFF/MMR,  
2: TIFF/MH, 3: TIFF/MR 
084  Format for Printer Color  0: JFIF/JPEG
, 1: TIFF/MMR,   
2: TIFF/MH, 3: TIFF/MR   
 
ƒ  This SP is not used in this model. 
085  Format for Printer B&W  0: JFIF/JPEG, 
1: TIFF/MMR,  
2: TIFF/MH, 3: TIFF/MR 
086  Format for Printer B&W HQ  0: JFIF/JPEG, 1: TIFF/MMR,   
2: TIFF/MH
, 3: TIFF/MR 
Default for JPEG 
[5 to 95 / 50 / 1 /step] 
091  Sets the JPEG format default fo
r documents sent to the document 
management server via the MLB with  JPEG selected as the format. 
Enabled only when optional MLB (Media  Link Board) is installed. 
  
						

							 
SM 5-257 B230/B237/D042 
Service 
Tables 
5839   [IEEE1394]   *CTL - 
007 Cycle Master  Turns the cycle master function on/off. 
[0 or 1 / 
1 / 1 /step] 
0: OFF   
1: ON 
008 BCR mode  Selects either ‘Standard’, IRM Color Copy, or 
Always Effective.
 
009 IRM 1394a Check  Turns the IRM 1394a check on/off. 
[0 or 1 / 
0 / - ] 
0: OFF   
1: ON 
If the IRM is not defined as 1394a standard, its 
node is used as IRM. 
010 Unique ID  [0 or 1 / 
1 / - ] 
0: OFF 
1: ON 
011 Logout  Prevents initiators from logging on or makes 
initiators log off. 
[0 or 1 / 
1 / - ] 
0: OFF (Prevents the initiators, having already 
logged on, to log on if they try to log on.) 
1: ON (Makes initiators , having already logged on, 
to log off if they try to log on.) 
012 Login  Allows/disallows an initiato
r to exclusively log on. 
[0 or 1 /  0 / - ] 
0: OFF (Disallows) 
1: ON (Allows) 
013 Login MAX  Specifies the maximum init
iators able to log on. 
[0 to 63 /  8 / 1 /step] 
 
5840   [IEEE 802.11b]   
						

							 
B230/B237/D042 5-258 SM 
Channel Max *CTL[1 to 11 or 13 / 
11  o r  1 3 / 1 /step] 
Europe/Asia: 1 to 13 
NA/ Asia: 1 to 11 
006  Sets the maximum number of channels available for data transmission via the 
wireless LAN. The number of channels ava
ilable varies according to location. 
The default settings are set for the ma ximum end of the range for each area. 
Adjust the upper 4 bits to se t the maximum number of channels.  DFU 
 
ƒ  Do not change the setting. 
Channel Min  *CTL[1 to 11 or 13 / 
1 / 1 /step] 
Europe: 1 to 13 
NA/ Asia: 1 to 11 
007  Sets the minimum number of channels av
ailable for data transmission via the 
wireless LAN. The number of channels ava ilable varies according to location. 
The default settings are set for the mi nimum end of the range for each area. 
Adjust the lower 4 bits to se t the minimum number of channels.  DFU 
 
ƒ  Do not change the setting. 
011  WEP key Select  *CTL Selects the WEP key. 
[00 to 11 / 
00 / 1 binary] 
00: Key #1 
01: Key #2 (Reserved) 
10: Key #3 (Reserved) 
11: Key #4 (Reserved) 
 
5841   [Supply Name Setting]  
001 Toner Name Setting: 
Black 
002 Toner Name Setting: 
Cyan 
003 Toner Name Setting:  *CTL 
Specifies supply names. These appear on 
the screen when the user presses the 
Inquiry button in the user tools screen.  
						

							 
SM 5-259 B230/B237/D042 
Service 
Tables 
Yellow 
004  Toner Name Setting: 
Magenta 
007 OrgStamp 
011 Staple Std1 
012 Staple Std2 
013 Staple Std3 
014 Staple Std4 
 
5842   [GWWS Analysis Mode] DFU  
001 Setting 1  *CTLDefault: 00000000
 – do not change 
Netfiles: Jobs to be printed from the 
document server using a PC and the 
DeskTopBinder software 
002 Setting 2  *CTLAdjusts the debug program modesetting. 
Bit7: 5682 mmseg-log setting 
0: Date/Hour/Minute/Second 
1: Minute/Second/Msec. 
0 to 6: Not used 
 
5844   [USB] 
Transfer Rate  *CTL0x01: Full speed   
0x04: Auto Change
 
001 
Adjusts the USB transfer rate. 
002 Vendor ID  *CTL
Displays the vendor ID.  DFU 
003 Product ID  *CTL
Displays the product ID.  DFU 
004  Device Release Number *CTL Displa ys the development release version  
						

							 
B230/B237/D042 5-260 SM 
number. DFU 
 
[Delivery Server 
Setting]  *CTL
- 
5845 
Provides items for deliv ery server settings. 
FTP Port No. 
[0 to 65535 / 3670 / 1 /step] 
001 
Sets the FTP port number used when image files to the Scan Router Server. 
IP Address  (Primary)  Range: 000.000.000.000  to 255.255.255.255 
002 
Use this SP to set the Scan Router Server address. The IP address under the 
transfer tab can be referenced by the initial system setting. 
Delivery Error Display Time  [0 to 999 / 300 / 1 second /step] 
006  Use this setting to determine the lengt
h of time the prompt message is 
displayed when a test error occurs dur ing document transfer with the NetFile 
application and an external device. 
IP Address  (Secondary)  Range: 000.000.000.000  to 255.255.255.255 
008 Specifies the IP address assigned to t
he computer designated to function as 
the secondary delivery server of Scan Rout er. This SP allows only the setting 
of the IP address without refe rence to the DNS setting. 
Delivery Server Model 
[0 to 4/ 0 / 1 /step] 
009  Allows changing the model of the deliver
y server registered by the I/O device.
0: Unknown 
1: SG1 Provided 
2: SG1 Package 
3: SG2 Provided 
4: SG2 Package 
010 Delivery Svr Capability  [0 to 255 / 0 / 1 /step] 
  Bit7 = 1 Comment information exits  Changes the  
						

							 
SM 5-261 B230/B237/D042 
Service 
Tables 
  Bit6 = 1 Direct specific ation of mail address possible 
  Bit5 = 1 Mail RX confirmation setting possible 
  Bit4 = 1 Address book autom atic update function exists 
  Bit3 = 1 Fax RX delivery function exists 
  Bit2 = 1 Sender password function exists 
  Bit1 = 1 Function to link MK-1 user and Sender exists 
  Bit0 = 1 Sender specification r equired (if set to 1, Bit6 is set 
to “0”)  capability of 
the registered 
that the I/O 
device 
registered. 
Delivery Svr Capability (Ext) 
[0 to 255 / 0 / 1 /step] 
Changes the capability of the registered that t he I/O device registered. 
011 
Bit7 = 1 Address book usage limitation  (Limitation for each authorized user) 
Bit6 = 1 RDH authorization link 
Bit5 to 0: Not used 
Server Scheme (Primary) 
013  NIA 
Server Port Number (Primary) 
014 NIA 
Server URL Path (Primary) 
015 
NIA 
Server Scheme (Secondary) 
016 NIA 
Server Port Number (Secondary) 
017 NIA 
018  Server URL Path (Secondary)  
						

							 
B230/B237/D042 5-262 SM 
NIA 
Capture Server Scheme 
019 
NIA 
Capture Server Port Number 
020 NIA 
Capture Server URL Path 
021 
NIA 
 
5846   [UCS Settings]  *CTL - 
Machine ID (For Delivery Server) 
Displays ID 
001 Displays the unique device ID in use by
 the delivery server directory. The 
value is only displayed and cannot be  changed. This ID is created from the 
NIC MAC or IEEE 1394 EUI. The ID is disp layed as either 6-byle or 8-byte 
binary. 
Machine ID Clear (For Delivery Server)  Clears ID 
002  Clears the unique ID of the device used 
as the name in the file transfer 
directory. Execute this SP if the connection of the devic e to the delivery 
server is unstable. After clearing t he ID, the ID will be established again 
automatically by cycli ng the machine off and on. 
Maximum Entries 
[2000 to 20000/ 2000 /1 /step] 
003 Changes the maximum number of 
entries that UCS can handle. 
If a value smaller than the present va lue is set, the UCS managed data is 
cleared, and the data (excluding user  code information) is displayed. 
Delivery Server Retry Timer 
[0 to 255 / 0 / 1 /step] 
006 
Sets the interval for retry attempts w hen the delivery server fails to acquire 
the delivery server address book. 
007  Delivery Server Retry Times  [0 to 255 / 0 / 1 /step]