Xerox WorkCentre 3045 Service Manual

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-11Service Parts Disassembly
Rear Cover
PL1.1.12
1. Open the Rear Door.
2. Remove the Main Tray (page 4-13).
3. Remove the Front Cover (page 4-15).
4. Remove the Right Cover (page 4-12).
5. Remove the Left Cover (page 4-16)
6. Lift the Fuser levers.
7. Remove the 4 screws (silver, tap, 8 mm) that secure the Rear Cover.
8. Release several hooks that secure the cover to the Top Cover and chassis.
s3040-025 
						

							4-12 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
Right Cover
PL1.1.13
1. Remove the Front Cover (page 4-15).
2. Open the Rear Door.
3. Release the 2 bosses on the bottom of the Right Cover.
4. Release several hooks that secure the cover to the Top Cover and chassis.
s3040-026 
						

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-13Service Parts Disassembly
Main Tray
PL1.1.14
1. Open the Main Tray.
2. Release the boss on the Main Tray from the hole in the Front Cover, and then 
remove the Tray.
s3040-027 
						

							4-14 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
HiPot Cover
PL1.1.19
1. Open the Main Tray.
2. Open the Toner Door.
3. Starting on the left edge, release the hooks on both sides of the cover. There is 
1 hook on the left, 2 hooks on the right.
s3040-052 
						

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-15Service Parts Disassembly
Front Cover
PL1.1.20
1. Remove the Main Tray (page 4-13).
2. Remove the 2 screws (silver, tap, 8 mm) that secure the Front Cover to the 
printer.
3. Starting on the bottom side, release the hooks on both sides of the printer, 
and remove the Front Cover. There are 2 hooks per side, and 2 on the top.
s3040-016
Hooks
Hooks 
						

							4-16 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
Left Cover
PL1.1.23
1. Remove the Front Cover (page 4-15).
2. Open the Rear Door.
3. Release the 2 bosses on the bottom of the Left Cover.
4. Release several hooks that secure the cover to the Top Cover and chassis.
s3040-028 
						

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-17Service Parts Disassembly
Phaser 3010/3040 Feeder
Feed Roll Assembly
PL2.2.1
1. Remove the Main Paper Tray (page 4-13).
2. Remove the Front Cover (page 4-15).
3. Remove the Rear Door (page 4-8).
4. Remove the Left Cover (page 4-16).
5. Remove the Right Cover (page 4-12).
6. Remove the Top Cover (page 4-7).
7. Remove the Rear Cover (page 4-11).
8. Remove the Toner Motor (page 4-37).
9. Remove the Toner Dispense Assembly (page 4-36).
10. Remove the Fuser (page 4-38).
11. Remove the Main Drive Assembly (page 4-40).
12. Remove the Main Drive Motor (page 4-41).
13. Remove the Power Switch Assembly (page 4-46).
14. Remove the MCU Board (page 4-43).
15. Remove the HVPS (page 4-42).
16. Remove the MCU Board bracket ().
17. Remove the IP Board (page 4-45).
18. Remove the LVPS (page 4-48).
19. Remove the IP Board and LVPS brackets (page 4-49).
20. Remove the Rear Door Interlock Switch (page 4-44).
21. Remove the xerographics assembly (page 4-33).
22. Remove the Feed Gear and Spring (page 4-25). 
						

							4-18 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
23. Remove 4 screws (silver, tap, 8 mm), that secure the lower plate to the chassis.
s3040-029 
						

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-19Service Parts Disassembly
24. Release the left Feed Roller Cam latch and slide the cam towards the center of 
the shaft.
25. Move the Feed Roll Assembly left to release the shaft from the chassis.
.
s3040-030 
						

							4-20 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
Bottom Plate
PL2.2.8
1. Remove the Main Paper Tray (page 4-13).
2. Remove the Front Cover (page 4-15).
3. Remove the Rear Door (page 4-8).
4. Remove the Left Cover (page 4-16).
5. Remove the Right Cover (page 4-12).
6. Remove the Top Cover (page 4-7).
7. Remove the Rear Cover (page 4-11).
8. Remove the Toner Motor (page 4-37).
9. Remove the Toner Dispense Assembly (page 4-36).
10. Remove the Fuser (page 4-38).
11. Remove the Main Drive Assembly (page 4-40).
12. Remove the Main Drive Motor (page 4-41).
13. Remove the Power Switch Assembly (page 4-46).
14. Remove the MCU Board (page 4-43).
15. Remove the MCU Board bracket ().
16. Remove the IP Board (page 4-45).
17. Remove the LVPS (page 4-48).
18. Remove the IP Board and LVPS brackets (page 4-49).
19. Remove the Rear Door Interlock Switch (page 4-44).
20. Remove the xerographics assembly (page 4-33).
21. Remove the Feed Gear and Spring (page 4-25).
22. Remove the Feed Roller (page 4-17).
23. Remove the bottom chute
s3040-053