Xerox WorkCentre 3045 Service Manual

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-41Service Parts Disassembly
Main Drive Motor
PL6.1.2
Caution
The gears of the Main Drive Assembly are not captive to the cover. Use care 
when removing the cover to maintain correct gear orientation.
1. Remove the Main Tray (page 4-13).
2. Remove the Front Cover (page 4-15).
3. Remove the Left Cover (page 4-16).
4. Remove the Top Cover (page 4-7).
5. Remove the Main Drive Assembly (page 4-40).
6. Disconnect P/J10, P/J13 and P/J23 from the MCU Board 
7. Remove the 2 screws (silver, metal, 6 mm), and 3 screws (silver, tap, 8mm) that 
secure the Main Drive Motor to the chassis.
s3040-044
P/J10
P/J23 P/J13 
						

							4-42 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
Phaser 3010/3040 Electrical
HVPS
PL7.1.2
1. Remove the Toner Cartridge (page 4-5).
2. Remove the Main Tray (page 4-13).
3. Remove the Front Cover (page 4-15).
4. Remove the Right Cover (page 4-12).
5. Remove the Top Cover (page 4-7).
6. Remove the Toner Motor (page 4-37).
7. Remove the Toner Dispense Assembly (page 4-36).
8. Remove the MCU Board (page 4-43).
9. Remove 4 screws (silver, metal, 6 mm) that secure the HVPS.
s3040-045 
						

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-43Service Parts Disassembly
MCU Board
PL7.1.2
1. Remove the Main Tray (page 4-13).
2. Remove the Front Cover (page 4-15).
3. Disconnect all connections on the MCU Board.
4. Remove 4 screws (silver, metal, 6 mm) that secure the MCU Board.
s3040-046
P/J14
P/J10
P/J13P/J15
P/J16
P/J17
P/J25
P/J18
P/J20
P/J21
P/J22 P/J23 
						

							4-44 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
Rear Door Interlock Switch
PL7.2.1
1. Remove the Main Tray (page 4-13).
2. Remove the Front Cover (page 4-15).
3. Remove the Rear Door (page 4-8).
4. Remove the Left Cover (page 4-16).
5. Remove the Right Cover (page 4-12).
6. Remove the Top Cover (page 4-7).
7. Remove the Power Switch Assembly ()
8. Remove the IP Board (page 4-45).
9. Remove the LVPS (page 4-48).
10. Remove the IP Board and LVPS brackets (page 4-49).
11. Release the 2 hooks that secure the switch to the chassis.
s3040-047
P/J204 
						

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-45Service Parts Disassembly
Image Processor Board
PL7.2.8
1. Remove the Main Tray (page 4-13).
2. Remove the Front Cover (page 4-15).
3. Remove the Right Cover (page 4-12)
4. Remove the Top Cover (page 4-7).
5. Disconnect all connections on the IP Board.
6. Remove 4 screws (silver, metal, 6 mm) that secure the IP Board.
Replacement Note
After replacing the IP Board, restore these customer settings:
• Control Panel language
• Default paper size
• Time zone, clock and date formats
• Preferred unit (mm or inch)
s3040-048
SJ9
SJ8
P/J1
P/J250 
						

							4-46 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
Power Switch Assembly
PL7.2.10
1. Remove the Main Tray (page 4-13).
2. Remove the Front Cover (page 4-15).
3. Remove the Right Cover (page 4-12).
4. Remove the Left Cover (page 4-16).
5. Remove the Top Cover (page 4-7).
6. Remove the Rear Cover (page 4-11).
7. Disconnect P/J201 from the LVPS.
8. Release the boss and raise the harness guide to access the upper screw that 
secures the Power Switch Assembly.
9. Disconnect P/J200 from the LVPS and remove 1 screw (silver, metal with 
washer 6mm) and 1 screw (silver metal, 6mm) that secure the Power Switch 
Assembly.
s3040-136AC Inlet Holder
P/J200 P/J201 
						

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-47Service Parts Disassembly
Replacement Note
Assemble the Power Switch Assembly into the holder as illustrated. Capture 
the ground wire under the lower screw.
s3040-049 
						

							4-48 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
LV P S
PL7.2.11
1. Remove the Main Tray (page 4-13).
2. Remove the Front Cover (page 4-15).
3. Remove the Right Cover (page 4-12).
4. Remove the Top Cover (page 4-7).
5. Disconnect all connections to the LVPS.
6. Remove 4 screws (silver, metal, 6mm) that secure the LVPS.
s3040-051
P/J203
P/J202
P/J204P/J201
P/J200 
						

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-49Service Parts Disassembly
IP Board and LVPS Brackets 
PL7.2.10
1. Remove the Main Tray (page 4-13).
2. Remove the Front Cover (page 4-15).
3. Remove the Right Cover (page 4-12).
4. Remove the Left Cover (page 4-16).
5. Remove the Top Cover (page 4-7).
6. Remove the Rear Cover (page 4-11).
7. Remove the Power Switch Assembly (page 4-46).
8. Remove the IP Board (page 4-45.
9. Remove the LVPS (page 4-48).
10. Release 1 hook to remove the front guide harness.
11. Remove the LVPS insulator.
s3040-050 
						

							4-50 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
12. Remove 5 screws (silver, tap, 8mm) and 4 screws (silver metal, 6mm) that 
secure the brackets.
13. Release the Rear Door Interlock Switch harness to remove the brackets.
Replacement Note
Install the ground spring when replacing the bracket.
s3040-056
s3040-057