Xerox WorkCentre 3045 Service Manual

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-101Service Parts Disassembly
Power Switch Assembly
PL7.2.6
1. Remove the Main Tray (page 4-58).
2. Remove the Front Cover (page 4-60).
3. Remove the Inner Front Cover (page 4-62).
4. Remove the Left Cover (page 4-64).
5. Remove the Right Cover (page 4-57).
6. Remove the Scanner (page 4-109).
7. Disconnect P/J7601 from the Front USB Board.
8. Disconnect P/J6501 from the WiFi Adaptor.
9. Remove the Top Cover (page 4-52).
10. Remove the Rear Cover (page 4-11).
11. Disconnect P/J201 from the LVPS.
12. Release the boss and raise the harness guide to access the upper screw that 
secures the Power Switch Assembly.
13. Disconnect P/J200 from the LVPS and remove 1 screws (silver, metal with 
washer 6mm) and 2 screws (silver metal, 6mm) that secure the Power Switch 
Assembly.
Replacement Note
Capture the ground wire with the screw and washer.
s3040-089
P/J200 
						

							4-102 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
LV P S
PL7.2.8
1. Remove the Main Tray (page 4-58).
2. Remove the Front Cover (page 4-60).
3. Remove the Inner Front Cover (page 4-62).
4. Remove the Right Cover (page 4-57).
5. Disconnect all connections to the LVPS.
6. Remove 4 screws (silver, metal, 6mm) that secure the LVPS.
s3040-090
P/J203
P/J202
P/J204P/J201
P/J200 
						

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-103Service Parts Disassembly
IP Board
PL7.3.3
1. Remove the Main Tray (page 4-58).
2. Remove the Front Cover (page 4-60).
3. Remove the Inner Front Cover (page 4-62).
4. Remove the Left Cover (page 4-64).
5. Disconnect all connections on the IP Board.
6. Remove the harness guides.
7. Remove 4 screws (silver, metal, 6 mm) that secure the MCU Board.
Replacement Note
After replacing the IP Board, check/change the following settings:
• FAX Settings > Country
• Control Panel language
s3040-091
SJ5
SJ6
SJ9
SJ8
SJ18
SJ19 SJ22 SJ2 SJ21 SJ23 SJ20SJ12
SJ11
J1
SJ911 
						

							4-104 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
• Default paper size
• Time zone, clock and date formats
• Preferred unit (mm or inch)
Also adjust the Scanner using “Scanner Adjustment” on page 6-7. 
						

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-105Service Parts Disassembly
Fa x  B o a rd
PL7.3.4
1. Remove the Main Tray (page 4-58).
2. Remove the Front Cover (page 4-60).
3. Remove the Inner Front Cover (page 4-62).
4. Remove the Left Cover (page 4-64).
5. Disconnect P/J102 from the Fax Board.
6. Remove 4 screws (silver, metal, 6mm) to remove the Fax Board.
s3040-092
P/J102 
						

							4-106 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
IP Board Bracket
PL7.3.5
1. Remove the Main Tray (page 4-58).
2. Remove the Front Cover (page 4-60).
3. Remove the Inner Front Cover (page 4-62).
4. Remove the Left Cover (page 4-64).
5. Remove the Right Cover (page 4-57).
6. Remove the Scanner (page 4-109).
7. Disconnect P/J7601 from the Front USB Board.
8. Disconnect P/J6501 from the WiFi Adaptor.
9. Remove the Top Cover (page 4-52).
10. Remove the Rear Cover (page 4-56).
11. Remove the IP Board (page 4-103).
12. Remove the Fax Board if present (page 4-105).
13. Release hooks that secure the 2 harness guides and feed the harnesses and 
guides through the holes in the bracket. 
14. Remove 1 screw (silver, tap, 8mm) and 4 screws (silver metal, 6mm) that 
secure the bracket.
s3040-093 
						

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-107Service Parts Disassembly
LV P S  B r a c k e t
PL7.2.4
Caution
The LVPS bracket uses a small spring to ground the bracket to the chassis.
1. Remove the Main Tray (page 4-58).
2. Remove the Front Cover (page 4-60).
3. Remove the Inner Front Cover (page 4-62).
4. Remove the Left Cover (page 4-64).
5. Remove the Right Cover (page 4-57).
6. Remove the Scanner (page 4-109).
7. Disconnect P/J7601 from the Front USB Board.
8. Disconnect P/J6501 from the WiFi Adaptor.
9. Remove the Top Cover (page 4-52).
10. Remove the Rear Cover (page 4-56).
11. Remove the Power Switch Assembly (page 4-101)
12. Remove the LVPS (page 4-102).
13. Release 2 hooks that secure the front harness guide and remove the guide and 
LV P S  i n s u l a t o r .
s3040-094 
						

							4-108 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
14. Remove 5 screw (silver, tap, 8mm) and 4 screws (silver metal, 6mm) that 
secure the bracket.
Replacement Note
Install the ground spring before securing the bracket to the chassis.
s3040-095
s3040-057 
						

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-109Service Parts Disassembly
WorkCentre 3045 Scanner and ADF
Scanner with ADF
PL8.1.1
Note
Scanners without an ADF have 3 connections; P/J5, 6 and 18.
1. Remove the Main Tray (page 4-58).
2. Remove the Front Cover (page 4-60).
3. Remove the Inner Front Cover (page 4-62).
4. Remove the Left Cover (page 4-64).
5. Remove the Right Cover (page 4-57).
6. Disconnect P/J5, 6, 18, 19, 20, 21, 22, and 23 from the IP Board.
s3040-096
SJ5
SJ6
SJ18 SJ19 SJ22 SJ21 SJ23 SJ20 
						

							4-110 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
7. Remove 1 screw that secures the ADF ground wire.
8. Remove the Holder Assemblies (page 4-51).
9. Lift the Scanner/ADF till vertical, pull the harnesses through the hole in the Top 
Cover and remove the Scanner Assembly.
s3040-154