Xerox WorkCentre 3045 Service Manual

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-21Service Parts Disassembly
24. Release the hook that secures the cam follwer bearings and remove the 
bearings and followers from the chassis.
s3040-031 
						

							4-22 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
25. Flex the Bottom Plate to release one end from the chassis and remove.
Replacement Note
Attach the spring to the Bottom Plate before installing the followers.
s3040-122 
						

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-23Service Parts Disassembly
Separator Pad Assembly
PL2.2.15
1. Remove the Rear Door (page 4-8).
2. Press inward on the left side retainer to release the left side boss and remove 
the lower chute.
3. Remove the Registration Sensor Actuator (page 4-28).
s3040-032 
						

							4-24 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
4. Release the boss hook at each side of the housing to release the assembly 
from the chassis.
s3040-033 
						

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-25Service Parts Disassembly
Feed Gear and Spring
PL2.2.19
Caution
The gears of the Main Drive Assembly are not captive to the cover. Use care 
when removing the cover to maintain the correct gear orientation.
1. Remove the Left Cover (page 4-16).
2. Remove the Main Drive Assembly (page 4-40).
3. Release the spring from the hook on the chassis.
4. Release the hook that secures the Feed Gear to the shaft.
s3040-054 
						

							4-26 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
Registration Pinch Roller
PL2.3.2
1. Open the Rear Door (page 4-8).
2. Remove the Left Cover (page 4-16).
3. Remove the Right Cover (page 4-12).
4. Remove the Top Cover (page 4-7).
5. Remove the Rear Cover (page 4-11).
6. Remove the Power Switch Assembly (page 4-46).
7. Remove the IP Board (page 4-45).
8. Remove the LVPS (page 4-48).
9. Remove the IP Board and LVPS brackets (page 4-49).
10. Remove the registration springs and bearings from the ends of the pinch roller 
shaft and remove the shaft from the chassis.
s3040-034 
						

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-27Service Parts Disassembly
Registration Roller
PL2.3.1
1. Open the Rear Door (page 4-8).
2. Remove the Left Cover (page 4-16).
3. Remove the Right Cover (page 4-12).
4. Remove the Top Cover (page 4-7).
5. Remove the Rear Cover (page 4-11).
6. Remove the Power Switch Assembly (page 4-46).
7. Remove the IP Board (page 4-45).
8. Remove the LVPS (page 4-48).
9. Remove the IP Board and LVPS brackets (page 4-49).
10. Remove the Main Drive Assembly (page 4-40).
11. Remove the registration pinch roller (page 4-26).
12. Remove the registration gear, clutch and spring from the Registration Roller 
shaft.
13. Remove the bearing from each end of the roller shaft, then remove the roller 
from the chassis.
s3040-035 
						

							4-28 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
Registration Sensor Actuator
PL2.3.9
1. Remove the Rear Door (page 4-8).
2. Press inward on the left side retainer to release the left side boss and remove 
the lower chute.
s3040-032 
						

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-29Service Parts Disassembly
3. Remove the Registration Sensor Actuator by releasing the left end from the 
chassis and
Replacement Note
Install the spring as shown below.
s3040-036
s3040-037 
						

							4-30 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
Registration Sensor
PL2.3.5
1. Open the Rear Door.
2. Press inward on the left side retainer to release the left side boss and remove 
the lower chute.
3. Remove the Registration Sensor Actuator (page 4-28).
s3040-032