Xerox WorkCentre 3045 Service Manual

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-111Service Parts Disassembly
ADF Assembly
PL 8.1.2
1. Remove the Main Tray (page 4-58).
2. Remove the Front Cover (page 4-60).
3. Remove the Inner Front Cover (page 4-62).
4. Remove the Left Cover (page 4-64).
5. Remove the Right Cover (page 4-57).
6. Disconnect P/J19, 20, 21, 22, from the IP Board.
7. Remove 1 screw that secures the ADF ground wire.
s3040-096
SJ18 SJ19 SJ22 SJ21 SJ23 SJ20
s3040-154 
						

							4-112 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
8. Release the hooks that secure the hinges to the Scanner and carefully pull the 
ADF harness through the hole.
Replacement Note
Leave adaquate slack in the ADF harness to allow the ADF to open and close 
without restriction. The ADF harness protective covering should extend all the 
way through the Scanner into the chassis. 
						

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-113Service Parts Disassembly
ADF Top Cover
PL8.1.3
1. Open the ADF Top Cover.
2. Release the ADF Top Cover from the bosses on the ADF Assembly.
s3040-098 
						

							4-114 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
ADF Separator Pad
PL8.1.4
1. Open the ADF Cover
2. Release the hook on the Separator Pad and remove it.
s3040-139 
						

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-115Service Parts Disassembly
ADF Input Tray
PL8.1.6
1. Open the ADF Cover
2. Bend the Input Tray rear side hinge to release the boss from the hole in the 
ADF Assembly.
3. Release the front side boss of the Input Tray to remove it.
s3040-099 
						

							4-116 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
Control Panel
PL8.1.101. Lift the Scanner Assembly.
2. Remove 2 screws (silver, with flange, tap, 8 mm).
3. Close the Scanner Assembly and remove the Control Panel.
s3040-100 
						

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-117Service Parts Disassembly
Document Cover
PL9.1.2
1. Open the Document Cover.
2. Release the hooks that secure the hinges to the Scanner. 
						

							4-118 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly 
						

							5
Chapter
Parts Lists
In this chapter...
• Serial Number Location and Range
• Using the Parts List
• Phaser 3010/3040 Parts Lists
• WorkCentre 3045 Parts Lists
• Xerox Supplies and Accessories
•Hardware Kit 
						

							5-2 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Parts Lists
Serial Number Location and Range
Changes to Xerox products are made to accommodate improved components. 
When ordering parts include this information:
• Components part number
• Product type or model number
• Serial Number of the printer
The serial number is located on the Rear Door.
Product Codes and Serial Number Ranges
ModelCodeLocalStartEndDescription
DMO-E
3010V_B BD8 317 673501 873500 3010V/B, USB, 220v
3040V_B BE0 317 873501 973500 3040V/B, USB, 220v
3045_B BE1 317 300501 348500 3045B, USB, Ethernet, 110V
3045_NI BE3 316 960001 983000 3045NI, USB, Wireless, 110V
DMO-W
3010_B BD7 316 260001 310000 3010B, USB, 110v
3040_B BD9 316 310001 335000 3040B, USB, 110v
3045V_B BN6 319 158001 273000 3045V/B, USB, Ethernet, 220V
3045_NI BN7 319 273001 353000 3045V/NI, USB, Wireless, 220V
MANUFACTURED: June, 2011
Xerox S/N: BE39060012
s3040-180