Xerox WorkCentre 3045 Service Manual

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-61Service Parts Disassembly
USB Cover
PL1.1.23
1. Starting on the right edge, release the hooks on both sides of the cover. There 
is 2 hooks on the bottom and 2 hooks on the right.
s3040-123 
						

							4-62 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
Inner Front Cover
PL1.1.24
1. Remove the Main Tray (page 4-58).
2. Raise the Scanner.
3. Remove the Front Cover (page 4-60).
4. Remove the 2 screws (silver, tap, 8 mm) that secure the Rear Cover.
5. Lift the cover at the upper corners to release 2 hooks that secure the cover.
s3040-065 
						

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-63Service Parts Disassembly
Output Tray Extension
PL1.1.25
1. Remove the Main Tray (page 4-58).
2. Raise the Scanner.
3. Remove the Front Cover (page 4-60).
4. Remove the Inner Front Cover (page 4-62).
5. Release the bosses that secure the Output Tray Extension to the inner Front 
Cover.
s3040-066 
						

							4-64 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
Left Cover
PL1.1.28
1. Remove the Main Tray (page 4-58).
2. Raise the Scanner.
3. Remove the Front Cover (page 4-60).
4. Remove the Inner Front Cover (page 4-62).
5. Release the 2 bosses on the bottom of the Left Cover.
6. Release several hooks that secure the cover to the Top and Rear Covers.
s3040-067 
						

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-65Service Parts Disassembly
Front USB Board
PL1.1.29
1. Remove the Main Tray (page 4-58).
2. Raise the Scanner.
3. Remove the Front Cover (page 4-60).
4. Remove the Inner Front Cover (page 4-62).
5. Remove the Left Cover (page 4-64).
6. Disconnect P/J7601 on the Front USB Board.
7. Remove the 2 screws (silver, tap, 8 mm) that secure the Front USB Board to the 
To p  C o v e r .
s3040-068
P/J7601 
						

							4-66 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
WiFi Adaptor (3045N)
PL1.1.31
1. Remove the Main Tray (page 4-58).
2. Raise the Scanner.
3. Remove the Front Cover (page 4-60).
4. Remove the Inner Front Cover (page 4-62).
5. Remove the Left Cover (page 4-64).
6. Disconnect P/J6501 on the IP Board.
7. Release 2 hooks that secure the WiFi Adaptor.
s0340-069
P/J6501 
						

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-67Service Parts Disassembly
WorkCentre 3045 Feeder
Bypass Tray
PL2.1.99
1. Release 2 hooks, one on each side, that secure the bypass tray in the chassis.
s3040-070 
						

							4-68 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
Feed Roll Assembly
PL2.2.1
1. Remove the Main Tray (page 4-58).
2. Remove the Front Cover (page 4-60).
3. Remove the Inner Front Cover (page 4-62).
4. Remove the Left Cover (page 4-64).
5. Remove the Right Cover (page 4-57).
6. Remove the Scanner (page 4-109).
7. Disconnect P/J7601 from the Front USB Board.
8. Disconnect P/J6501 from the WiFi Adaptor.
9. Remove the Top Cover (page 4-52).
10. Remove the Rear Cover (page 4-11).
11. Remove the Toner Motor (page 4-37).
12. Remove the Toner Dispense Assembly (page 4-36).
13. Remove the Fuser (page 4-38).
14. Remove the MCU Board (page 4-43).
15. Remove the HVPS (page 4-98).
16. Remove the Power Switch Assembly (page 4-46).
17. Remove the LVPS (page 4-48).
18. Remove the LVPS bracket (page 4-107).
19. Remove the Rear Door Interlock Switch (page 4-44).
20. Remove the IP Board (page 4-45).
21. Remove the Fax Board if present (page 4-105).
22. Remove the IP Board bracket (page 4-106).
23. Remove the Main Drive Assembly (page 4-40).
24. Remove the Main Drive Motor (page 4-41).
25. Remove the xerographics assembly (page 4-33). 
						

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-69Service Parts Disassembly
26. Remove 4 screws (silver, tap, 8 mm), that secure the lower plate to the chassis.
27. Remove the Feed Gear and Spring (page 4-76).
28. Release the left Feed Roller Cam latch and slide the cam towards the center of 
the shaft., and move the Feed Shaft to the left side of the printer.
29. Move the Feed Roll Assembly left to release the shaft from the chassis.
s3040-029 
						

							4-70 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
.
s3040-072