Xerox WorkCentre 3045 Service Manual

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only A-3Reference
CE Diags Menu Tree
ESS Diag
Digital Input
Digital Output
NVM Setting-Write
Print Info
Installation Set
Test Print
Parameter
Flash ROM Test
DRAM Test
IOT Test
Light Flash R/W Test
OP Panel Test
All Test
Config Page
Print Settings
Serial No.
Pixel Counter
Print Counter
Clear All NVM
Clear Job History
Test Pat ASIC [IOT]
Test Pattern LPH K [IOT]
Registration
Machine/Toner
Print Parameters
s3040-169 
						

							A-4 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Reference
CE Diagnostics Screen
The CE Diags screen has four tabs.
• Printer Settings Report
Provides printer information, menu settings, information pages, and TCP/IP 
settings.
• Printer Maintenance
Provides access to printer settings such as paper type, altitude adjustment, 
and Fuser adjustments.
• Diagnosis
Outputs the test charts incorporated in the printer.
•CE Diag
Checks the operation of internal parts of the printer, prints out the printer 
information, changes the adjusted values, and implements other functions.
Note
Open the CE Diag tab by entering Control_C, -E simultanusly in the Printer 
Setting Utilities screen.
Select the menu in this screen.s3040-178 
						

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only A-5Reference
ESS Diagnostics
ESS tests exercise major printer subsystems.
Digital Input Tests
Select the component from the drop down box. Click the Start button to begin the 
test. LOW or HIGH is displayed on the Result screen. The component operation is 
checked in such a way that the component status is changed from [LOW] to 
[HIGH] and vice versa by operating the actuator or opening/closing the door. To 
stop the operation, click Stop. Component tests availabe under Digital Input are:
• Registration Sensor
•Exit Sensor
• Rear Door Interlock
• Toner Cartridge CRUM
Digital Output Tests
Select the component from the drop down box. Click the Start button to begin the 
test. As many as ten different components can be simultaneously operated. 
However, it is recommended to operate one or two components at a time since 
simultaneous operation of many different components can break them. To stop 
the operation, click Stop. Component tests availabe under Digital Output are:
• Main Motor Normal
•Main Motor Slow
•Feed Solenoid On
• Dispense Motor On ESS Diag Tests
ItemFunction
FlashROM Test This test calculates the ROM 
checksum and compares it with the 
valid checksum stored beforehand
DRAM Test Tests OPEN/SHORT with the address 
line of the DRAM. Performs write/
read/verify on the entire DRAM.
IOT Test Tests communication with the IOT.
Light Flash R/W Test The Flash memory testing has design 
back up the data and restores original 
data in test area.
OP Panel (Control Panel) Test The OP panel test includes LCD, LED 
and Key tests.
All Test This test executes the all ESS tests. 
						

							A-6 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Reference
NVM Operations
CS Diagnostics includes utilities for managing NVM.
Print Info
Installation Set
Displays values of the printer’s counters and sets service tags. To apply changes, 
click the Apply New Settings button, or the Restart printer to apply new settings 
button.
ScreenPurpose
NVM Settings - Write Used for changing the settings for internal 
data of the printer.
This operation is prohibited since it can 
damage the internal data.
NVM Settings - Read Used for confirming the internal data of the 
printer.
NVM Settings - Save NVM to ESS Saves the internal data of the MCU Board to 
the Image Processor Board. This is used 
when the MCU Board needs to be replaced
Settings - Load NVM from ESS Loads the internal data saved via NVM 
Settings - SaveNVM to ESS to the new MCU 
Board.
ScreenPurpose
Config Page The current version of software and the 
configuration of the printer can be 
confirmed by executing this test. Click the 
Config Page button to print the “Config 
Page”.
Print Settings The service tag, printing count value and 
error count value can be confirmed by 
executing this test. Push the Print Settings 
button to print the “Print Settings” page.
ScreenPurpose
Serial Number Serial number of the printer.
Pixel Counter Pixel count values. (read only) 
						

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only A-7Reference
Te s t  P r i n t
Two test prints are available, Test pattern ASIC and LPH K. Select the pattern from 
the menu and click the print button.
Parameter
This function reads/writes the parameters in the table. Click Apply new settings or 
Restart printer to apply new settings button after the setting is completed to 
change the value in NVM.Print Counter Displays the respective counter values in the 
master NVM and backup NVM. (read only)
Clear All NVM Initializes the NVM of the Image Processor 
Board.
Clear Job Log Initializes the print job history. 
Apply New Settings This button should be clicked to move to any 
other setting menu from the current menu in 
operation.
NOTE  After completion of all operations the Restart 
printer to apply new settings button should be 
clicked without exceptions.
Restart printer to apply new 
settingsClick this button when ready to apply your 
changes to the settings.
The restart of a printer is required in order to 
confirm this setup.
ItemRangeParameterFunction
Registration -94 ~ 94 Regi Lead Offset Value of Lead Offset
-68  ~ 68 Regi Side Offset Value of Side Offset
Machine - Total PV Counter of Total PV
- FC PV Counter of FC PV
- DEVE Round time K Counter of DEVE Round time
- XERO Round time Counter of XERO Round time
- K Dispense Time Counter of Dispense Time
- K Pixel Counter of K Pixel
- Sheets of Custom Mode Start Counter of Sheets of Custom Mode Start
- Sheets of Custom Mode End Counter of Sheets of Custom Mode End
To n e r - K  To n e r  P V C o u n t e r  o f  To t a l  P V
- K Toner Pixel Counter of Toner Pixel
- Life K Toner Dispense Time Counter of Toner Dispense Time
- Life K Toner Waste toner count Counter of Toner Waste toner count 
						

							A-8 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Reference
Acronyms and Abbreviations
AcronymDescription
A3 Paper size 297 millimeters (11.69 inches) x 420 millimeters 
(16.54 inches).
A4 Paper size 210 millimeters (8.27 inches) x 297 millimeters (11.69 
inches).
A5 Paper size 148 millimeters (5.82 inches) x 210 millimeters (2.10 
inches).
AC Alternating Current is type of current available at power source 
for the printer.
ADC Automatic Density Control
AMPV Average Monthly Print Volume
APC Auto Power Control
ASSY Assembly
ATM Adobe Type Manager
BCR Bias Charge Roller
BOOTP Boot Parameter Protocol
BT R B i a s  Tra n s fe r  Ro l l e r
CCD Charge Coupled Device (Photoelectric Converter)
CCW Counter-Clock Wise
CMYK Toner colors for the printer:
Y=yellow, C=cyan, M=magenta, K=black
CRU Customer Replaceable Unit
CRUM Customer Replaceable Unit Meter/Memory
CST Cassette
dB Decibel
DC Direct Current
DDNS Dynamic Domain Name System
DDR2 DIMM Double Data Rate Dual In-Line Memory Module
DEV Developer
DHCP Dynamic Host Configuration Protocol
DPI Dots Per Inch
DRV Drive
DUP Duplex
Duplex 2-sided printing
EA Emulsion Aggregation (Toner)
EEPROM Electrically Erasable Programmable Read-Only Memory 
						

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only A-9Reference
ESD Electrostatic Discharge. A transfer of charge between bodies at 
different electrostactic potential.
ESS Image process controller
FCC Federal Communications Commission
FDR Feeder
FPOT First Print Output Time
FRU Field Replaceable Unit
GB Giga Byte
GDI Graphics Device Interface
GND Ground
HARN Harness
HCF High-Capacity Feeder
HDD Hard Disk Drive
HUM Humidity
HV High Voltage
HVPS High-Voltage Power Supply
Hz Hertz (cycles per second)
IDT Intermediate Drum Transfer
IEC International Electrotechnical Commission
I/F Interface
IIT Image Input Terminal - ADF, Scanner
IOT Image Output Terminal - the printer
IP Image Processor
KB Kilo Byte
LAN Local Area Network
LCD Liquid Crystal Display
LD Laser Diode
LED Light Emitting Diode
LEF Long-Edge Feed
LPD Line Printer Daemon
LPR Line Printer Remote
LTR Letter Size Paper (8.5 x 11 inches)
LV P S L o w - Vo l t a g e  Po w e r  S u p p l y
MB Mega Byte
MCU Machine Control Unit (Engine Control Board)
MHz Mega Hertz
MIB Management Information Base
AcronymDescription 
						

							A-10 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Reference
MM Millimeters
MOT Motor
MPT Multi-Purpose Tray
NCS Non-Contact Sensor
NVM Non-Volatile Memory
NVRAM Non-Volatile Random Access Memory
OHP Overhead Paper (Transparency)
OPT Optional
OS Operating System
PCB Printed Circuit Board
PCL Printer Command Language
PDL Page Description Language
P/J Plug Jack (electrical connections)
PJL Printer Job Language
PL Parts List
POP3 Post Office Protocol version 3
PPD PostScript Printer Description
PPM Pages Per Minute
PWBA Printed Wiring Board Assembly
RAM Random Access Memory
RH Relative Humidity
RMS Root Mean Square Voltage
ROM Read-Only Memory
ROS Raster Output Scanner - Laser Unit
SEF Short-Edge Feed
SMB Server Message Block
SNMP Simple Network Management Protocol
SNR Sensor
SOL Solenoid
SOS Start of Scan
TDC Toner Density Control
TNR Toner
UI User Interface
USB Universal Serial Bus
WINS Wireless Integrated Network Sensor
AcronymDescription 
						

							Copyright © 2011, Xerox Corporation. 
All rights reserved. Unpublished 
rights reserved under the copyright 
laws of the United States.
Part#: 702P00125