Xerox WorkCentre 3045 Service Manual

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-91Service Parts Disassembly
Replacement Note
Capture the ground wire between the screw and motor mounting tab.
P/J150
s3040-043 
						

							4-92 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
Fuser
PL5.1.1
Wa rn i n g
Allow the Fuser to cool before servicing the printer.
1. Remove the Main Tray (page 4-58).
2. Remove the Front Cover (page 4-60).
3. Remove the Inner Front Cover (page 4-62).
4. Remove the Toner Cartridge (page 4-5).
5. Remove the Right Cover (page 4-57).
6. Remove the Left Cover (page 4-64).
7. Remove the Scanner (page 4-109).
8. Disconnect P/J7601 from the Front USB Board.
9. Disconnect P/J6501 from the WiFi Adaptor.
10. Remove the Top Cover (page 4-52).
11. Open the Rear Door.
12. Remove the Rear Cover (page 4-11).
13. Disconnect P/J201 on the LVPS, and release the harness from the guide.
14. Disconnect P/J18 from the MCU Board.
15. Remove 3 screws (hex-head, tap, 10mm) that secure the Fuser to the chassis. 
						

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-93Service Parts Disassembly
Replacement Note
Install the Fuser wiring in the harness guides as shown.
s3040-085
P/J201 P/J18 
						

							4-94 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
Top Side
s3040-153 
						

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-95Service Parts Disassembly
WorkCentre 3045 Drive
Main Drive Assembly
PL6.1.1
Caution
The gears of the Main Drive Assembly are not captive to the cover. Use care 
when removing the cover to maintain the correct gear orientation.
1. Remove the Main Tray (page 4-58).
2. Remove the Front Cover (page 4-60).
3. Remove the Inner Front Cover (page 4-62).
4. Remove the Left Cover (page 4-64).
5. Remove the Right Cover (page 4-57).
6. Remove the Scanner (page 4-109).
7. Disconnect P/J7601 from the Front USB Board.
8. Disconnect P/J6501 from the WiFi Adaptor.
9. Remove the Top Cover (page 4-52).
10. Remove the Rear Cover (page 4-56).
11. Remove the IP Board (page 4-103).
12. Remove the Fax Board if present (page 4-105).
13. Remove the IP Board bracket (page 4-106). 
						

							4-96 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
14. Remove the 2 screws (silver, metal, 6 mm), and 1 screw (silver, tap, 8mm) that 
secure the Main Drive Assembly to the chassis.
s3040-086 
						

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-97Service Parts Disassembly
Main Drive Motor
PL6.1.2
Caution
The gears of the Main Drive Assembly are not captive to the cover. Use care 
when removing the cover to maintain correct gear orientation.
1. Remove the Main Tray (page 4-58).
2. Remove the Front Cover (page 4-60).
3. Remove the Inner Front Cover (page 4-62).
4. Remove the Left Cover (page 4-64).
5. Remove the Right Cover (page 4-57).
6. Remove the Scanner (page 4-109).
7. Disconnect P/J7601 from the Front USB Board.
8. Disconnect P/J6501 from the WiFi Adaptor.
9. Remove the Top Cover (page 4-52).
10. Remove the Rear Cover (page 4-56).
11. Remove the IP Board (page 4-103).
12. Remove the Fax Board if present (page 4-105).
13. Remove the IP Board Bracket (page 4-106).
14. Remove the Main Drive Assembly (page 4-95).
15. Disconnect P/J10 and P/J23 from the MCU Board 
16. Remove the 2 screws (silver, metal, 6 mm), and 3 screws (silver, tap, 8mm) that 
secure the Main Drive Motor to the chassis.
s3040-044
P/J10
P/J23 P/J13 
						

							4-98 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
WorkCentre 3045 Electrical
HVPS
PL7.1.2
1. Remove the Main Tray (page 4-58).
2. Remove the Front Cover (page 4-60).
3. Remove the Inner Front Cover (page 4-62).
4. Remove the Left Cover (page 4-64).
5. Remove the Right Cover (page 4-57).
6. Remove the Scanner (page 4-109).
7. Disconnect P/J7601 from the Front USB Board.
8. Disconnect P/J6501 from the WiFi Adaptor.
9. Remove the Top Cover (page 4-52).
10. Remove the Toner Motor (page 4-37).
11. Remove the Toner Dispense Assembly (page 4-36).
12. Remove the MCU Board (page 4-43).
13. Remove 4 screws (silver, metal, 6 mm) that secure the HVPS.
s3040-087 
						

							Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-99Service Parts Disassembly
MCU Board
PL7.1.3
1. Remove the Main Tray (page 4-58).
2. Remove the Front Cover (page 4-60).
3. Remove the Inner Front Cover (page 4-62).
4. Remove the Left Cover (page 4-64).
5. Remove the Right Cover (page 4-57).
6. Remove the Scanner (page 4-109).
7. Disconnect P/J7601 from the Front USB Board.
8. Disconnect P/J6501 from the WiFi Adaptor.
9. Remove the Top Cover (page 4-52).
10. Disconnect all connections on the MCU Board.
11. Remove 4 screws (silver, metal, 6 mm) that secure the MCU Board.
s3040-088
P/J14
P/J10
P/J13P/J15
P/J16
P/J17
P/J25
P/J18
P/J20
P/J21
P/J22 P/J23 
						

							4-100 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
Rear Door Interlock Switch
PL7.2.1
1. Remove the Main Tray (page 4-58).
2. Remove the Front Cover (page 4-60).
3. Remove the Inner Front Cover (page 4-62).
4. Remove the Left Cover (page 4-64).
5. Remove the Right Cover (page 4-57).
6. Remove the Scanner (page 4-109).
7. Disconnect P/J7601 from the Front USB Board.
8. Disconnect P/J6501 from the WiFi Adaptor.
9. Remove the Top Cover (page 4-52).
10. Remove the Rear Cover (page 4-56).
11. Remove the Power Switch Assembly (page 4-101)
12. Remove the LVPS (page 4-48).
13. Remove the LVPS bracket (page 4-107).
14. Release the 2 hooks that secure the switch to the chassis.
s3040-047
P/J204