Canon printer MAXIFY MB2320 User Manual

							•At the time of purchase, ERROR TX REPORT is set to be printed only when a
transmission error occurred.
You can set the machine to print TX REPORT each time it sends a document, or disable printing of the report by selecting  TX report in Auto print settings  under FAX
settings .
You can also specify the print setting so that the first page of the fax is printed along
with the report.
Auto print settings
Note
•
The first page of the fax is not printed in color transmission.
•
MULTI TRANSMISSION REPORT is printed after sequential broadcasting of a
document.
•
If an error occurs when you send a fax, the error number is printed on ERROR TX REPORT (there are some errors for which the cause is also printed).
For details on the error number, see 
Errors When You Send a Fax .
MULTI
TRANSMISSION
REPORTThis report is printed after sequential broadcasting of a document.
Confirms whether the transmission to all the recipients has been completed successfully.
The procedure to print and the error number is same as TX REPORT.RX REPORTThis report is printed after each fax reception.•
At the time of purchase, the machine is set so that RX REPORT is not printed at all.
You can set the machine to print RX REPORT each time it receives a document, or
only when an error occurs by selecting  RX report in Auto print settings  under FAX
settings .
Auto print settings
•
If an error occurs when you receive a fax, the error number is printed on RX REPORT
(there are some errors for which the cause is also printed).
For details on the error number, see 
Errors When You Receive a Fax .
MEMORY CLEAR
REPORTLists the deleted faxes in the machine's memory if the faxes stored in the machine's
memory are deleted by a power failure or unplugging the power cord.
When the machine is turned on,  The power cord has been unplugged and unsent/
received docs in memory have been lost. Load paper and tap [OK] to print a list of
the lost docs.  is displayed on the touch screen. MEMORY CLEAR REPORT is printed by
tapping  OK on the touch screen.
Printing Report or List
This section describes the procedure to print the report or the list manually.
Print the following report or list manually.
•
ACTIVITY REPORT
•
Directory list (RECIPIENT TELEPHONE NUMBER LIST/GROUP DIAL TELEPHONE NO. LIST)
•
USER'S DATA LIST
•
MEMORY LIST
•
REJECTED NUMBER LIST
881 
						

							•CALLER HISTORY
Note
•
CALLER HISTORY may not be supported depending on the country or region of purchase.
1.
Make sure that the machine is turned on.
2.
Load paper.
3.
Flick the HOME screen, then tap  FAX .
Using the Operation Panel
The Fax standby screen is displayed.
4.
Tap  Function list .
The  Function list  screen is displayed.
5.
Tap Print reports/lists .
6.
Select a report or a list you want to print to start printing.
•
When you select Directory list:
Select  Recipient  or Group dial .
If you select  Recipient, select whether to print RECIPIENT TELEPHONE NUMBER LIST in
alphabetical order of the registered names. If you select  Yes, the machine prints RECIPIENT
TELEPHONE NUMBER LIST with the destination names in alphabetical order. If you select  No,
the machine prints RECIPIENT TELEPHONE NUMBER LIST with the registered entries in numerical order.
If you select  Group dial, the confirmation screen is displayed. Select  Yes. The machine prints
GROUP DIAL TELEPHONE NO. LIST.
•
When you select an item other than  Directory list:
Select  Yes when the confirmation screen is displayed.
The machine prints the selected report or list.
Errors When You Send a Fax If an error occurs when you send a fax, the error number is printed on ERROR TX REPORT or ACTIVITYREPORT (there are some errors for which the cause is also printed).
The causes corresponding to the error numbers are as follows.
No.CauseAction#001Document is jammed in
the ADF.The document is jammed in the ADF.
When the error is cleared, redo the operation.#003Document is too long.You attempted to send a document longer than 15.75 inches / 400 mm.
882 
						

							You cannot send a document longer than 15.75 inches / 400 mm from the ADF."#003" is also printed if it takes time to send a page. Divide the document or set
the image quality (Fax resolution) to a lower setting, then resend it.#005No answer.The recipient's fax machine does not respond.
Contact the recipient and have the recipient check that the telephone line isconnected correctly.#012No paper is in the
recipient's fax machine.There is no paper in the recipient's fax machine.
Contact the recipient and have the recipient load paper.#017No tone is detected.The machine could not detect the dial tone.
Dial tone detect  in Advanced FAX settings  under FAX settings  is set to ON.
Set to  OFF.
Advanced FAX settings
#018Line was busy.The fax/telephone number you dialed is busy.
Try dialing again after waiting for a moment.#022Number is deleted.The fax/telephone number registered in the machine's directory is incorrect. Check the recipient's fax/telephone number, correct the fax/telephone number
registered in the machine's directory, then send the document again.
Changing Registered Information
#037Memory is full.The machine could not send a fax because its memory is full.
Delete contents in memory, then send a fax again.
Document Stored in Machine's Memory
#059Transmission has been
canceled due to a fax
information mismatch.Transmission has been canceled because the machine could not detect the recipient's fax machine information or the information did not match the dialed number. This message is displayed when  Check RX FAX information in
Security control  under FAX settings  is set to ON.
For details, see 
Sending Faxes after Checking Information (Checking the
Recipient's Information) .
#085Try again in black & white
transmission.The recipient's fax machine is not color-compatible.
Resend the document in black & white.#099The  Stop  button was
pressed during
transmission.The  Stop  button was pressed to cancel transmission of the document. Resend it
if necessary.#412The fax could not be sent
from the computer.The fax could not be sent from the computer (Windows only). Ensure that the machine is connected with the computer correctly and redo operation.#995The unsent fax was
deleted while automatic
redialing.While automatic redialing, the unsent fax is stored in the machine's memory
temporarily until the sending fax is complete. If a power failure occurs or you
unplug the power cord before automatic redialing is complete, all faxes stored in
the machine's memory are deleted and not sent.
Resend the document.
883 
						

							Errors When You Receive a Fax
If an error occurs when you receive a fax, the error number is printed on RX REPORT or ACTIVITY
REPORT (there are some errors for which the cause is also printed).
The causes corresponding to the error numbers are as follows.No.CauseAction#003It takes too long to
receive a page.Contact the sender and have the sender divide the fax or set the image quality (Fax resolution) to a lower setting and resend it.#005No answer.When receiving a fax manually, the machine could not detect the signals from the
sender's fax machine.
Contact the sender and have the sender resend it, or set the machine to receive the fax automatically.#037Memory is full.The machine could not receive a fax because its memory is full.
Delete contents in memory, then ask the sender to resend the fax. See 
Document
Stored in Machine's Memory .
#046Reception has been
rejected due to the
specified fax rejection
condition.Reception has been rejected because the fax matches the fax rejection condition
specified by  FAX reception reject  in Security control  under FAX settings .
For details, see 
Rejecting Fax Reception .
#099The Stop  button was
pressed during
reception.The  Stop  button was pressed to cancel reception of the fax. Contact the sender
and have the sender resend it if necessary.#995The received fax was
deleted.The received fax was deleted before being saved to the USB flash drive,
forwarded to the shared folder on the computer, or printed. Contact the sender and
have the sender resend it if necessary.
884 
						

							Sending Faxes from a Computer
Sending a FAX (Fax Driver) Basic
Creating an Address Book (Fax Driver)
Edit or Remove a Recipient from an Address Book (Fax Driver)
Search for a Recipient in an Address Book (Fax Driver)
Troubleshooting Problems Sending Faxes (Fax Driver)
How to Open the Setting Screen of the Fax Driver
General Notes (Fax Driver)
885 
						

							Sending a FAX (Fax Driver)You can send faxes using the fax driver from applications that support document printing.
Note
•
Only black and white transmission is supported.
1.
Make sure that the machine is turned on.
2.
Open the document you want to fax with an application (such as Notepad), and then click
the Print command. (The command is  Print... on the  File menu.)
3.
In Select Printer  or Name  in the  Print dialog box, select  Canon XXX series FAX  (where
"XXX" is the model name).
4.
Click  Print or OK .
* Print  dialog box in Notepad
Note
•
Click  Preferences  or Properties  in the Print dialog box to open the print settings dialog box of
the fax driver in which you can set the paper size and print orientation. For details on how to open
the print settings dialog box of the fax driver, see "
How to Open the Setting Screen of the Fax
Driver ."
5.
Click  Display Address Book...  in Set Recipient  in the Send FAX  dialog box.
886 
						

							6.
Select a recipient from Recipient Name in the Select Recipient from Address Book
dialog box, then click  Set as Recipient.
The selected recipient is reflected in  Recipient in the Send FAX  dialog box.
Important
•
You cannot specify a recipient if there is no recipient registered in the address book. Register the
recipient in the address book and reopen the address book.
For details on how to register recipients in the address book, see "
Creating an Address Book (Fax
Driver) ."
•
If the recipient's fax/telephone number is entered incorrectly or the registered fax/telephone
number is incorrect, the fax may be sent to an unexpected recipient. When sending an important
fax, it is recommended that you send it after confirming the entered information and recipient's
status.
Note
•
You can also specify  Recipient by entering the  Recipient Name  and Fax Number  in Direct
Entry  in the  Send FAX  dialog box and then clicking  Set as Recipient.
•
For details on valid characters, see "General Notes (Fax Driver) ."
•
You can send faxes even if only the  Fax Number is entered.
887 
						

							•You can register the recipient you entered to the address book by clicking Add to Address
Book... . For details on how to register recipients in the address book, see "
Creating an
Address Book (Fax Driver) ."
•
Add the outside line access number before the fax number as needed.
(Example: When the outside line access number is "0" and the fax number is "XXX-XXXX", enter
"0XXX-XXXX".)
7.
Click  Send Now .
When a confirmation message is displayed, click  OK.
Important
•
If you cannot send a fax due to line failure, etc., see "Troubleshooting Problems Sending Faxes
(Fax Driver) ."
Canceling Transmission
If you click  Send Now in the Send FAX  dialog box, the printer icon is displayed in the taskbar. Double-
click this icon to display the list of fax jobs awaiting transmission or being sent.
Right-clicking a job and selecting  Cancel stops transmission.
888 
						

							Creating an Address Book (Fax Driver)By using the address book, you can send a fax by simply specifying a recipient from it. You can register the
recipient's name, fax number and other information in the address book.
Registering a recipient (WAB contact) in the address book
You can register an individual recipient (Contact) in the address book.1.
Open the print settings dialog box of the fax driver.
2.
Click  Address Book...  in the displayed dialog box.
Note
•
In Windows XP, when you open the address book for the first time, the  Setup Windows
Address Book  dialog box will be displayed. Refer to "
Setup when Opening the Address Book
for the First Time (Windows XP)" for details.
•
In Windows 8.1/Windows 8/Windows 7/Windows Vista, you can register an individual recipient
(Contact) in the address book folder (Windows Contacts) as an address book file (.contact file)
which can be used in multiple applications. However, you cannot change the address book you use, as only one address book can be created per user.
Follow the steps below to open Windows Contacts.
•
Windows 8.1/Windows 8:
Select the  Search charm, then search for "Contacts".
•
Windows 7/Windows Vista:
Select  XXXX (user name)  from the Start menu, then double-click  Contacts.
3.
In the Address Book  dialog box, click  New.
889 
						

							4.
Select Contact  in the New Entry  dialog box, then click  OK.
Note
•
For faxing, you can only specify the  Contact (one recipient). You cannot specify a  Distribution
List .
5.
Enter the  First, Middle , and Last of the contact in the  Name and E-mail tab (Name  tab
when using Windows XP) on the Properties dialog box.
The recipient's name will be printed at the top of the fax received by the recipient.
890