Canon printer PIXMA MG5622 User Manual

							LCD and Operation PanelYou can select the function such as copy or scan from the  HOME screen on the LCD.
The  HOME  screen consists of three screens. You can use the 
 or  button (A) to switch between them.
To select a menu, press the left, center, or right  Function button (B).
On the menu screen or settings screen, use the 
, , , or  button (C) to select an item or option, then
press the  OK button (D) to proceed with the procedure.
To return to the previous screen, press the  Back button (E).
Using the Function Buttons
Function menu (F) will appear when required at the bottom of the LCD screen. To use a function in a
function menu, press the corresponding  Function button (G), (H), or (I).
The number of function menus and their options vary depending on the screen. Check the function menus
displayed at the bottom of the screen, then select the one desired.
Example: The screen in  Scan
141 
						

							(G) Press the left Function button to select  Save/Forward. The screen for selecting destinations to save
or forward the scanned photo data will appear.
(H) Press the center  Function button. The  Document setting  screen will appear.
(I) Press the right Function button to select  Scan settings. The scan settings screen will appear.
142 
						

							Loading Paper / Originals
Loading Paper
Loading Originals
143 
						

							Loading Paper
Loading Plain Paper / Photo Paper
Loading Envelopes
Media Types You Can Use
Media Types You Cannot Use
Printing Area
144 
						

							Loading Plain Paper / Photo PaperYou can load plain paper or photo paper.
Important
•
If you cut plain paper into small size such as 4" x 6" (10 x 15 cm) or 5" x 7" (13 x 18 cm) to perform trial
print, it can cause paper jams.
Note
•
We recommend Canon genuine photo paper for printing photos.
For details on the Canon genuine paper, see 
Media Types You Can Use .
•
You can use general copy paper.
For the page size and paper weight you can use for this machine, see 
Media Types You Can Use .
1.
Prepare paper.
Align the edges of paper. If paper is curled, flatten it.
Note
•
Align the edges of paper neatly before loading. Loading paper without aligning the edges may
cause paper jams.
•
If paper is curled, hold the curled corners and gently bend them in the opposite direction until the paper becomes completely flat.
For details on how to flatten curled paper, see "Load the paper after correcting its curl." in 
Paper Is
Smudged/Printed Surface Is Scratched .
•
When using Photo Paper Plus Semi-gloss SG-201, even if the sheet is curled, load one sheet at a
time as it is. If you roll up this paper to flatten, this may cause cracks on the surface of the paper
and reduce the print quality.
2.
Load paper.
1.
Open the front cover gently.
145 
						

							2.
Holding the right tab on the front cover, pull out the cassette until it stops.
3.
Use the right paper guide (A) to slide both paper guides all the way out.
4.
Load the paper in the center of the cassette WITH THE PRINT SIDE FACING DOWN.
Push the paper stack all the way to the back of the cassette.
Important
•
Always load paper in the portrait orientation (B). Loading paper in the landscape orientation (C) can cause paper jams.
146 
						

							5.
Slide the right paper guide (A) to align the paper guides with both sides of the paper stack.
Do not slide the paper guides too hard against the paper. The paper may not be fed properly.
Note
•
Do not load sheets of paper higher than the load limit mark (D).
•
Keep the paper stack height below the tabs (E) of the paper guides.
•
Load small size paper, such as 4" x 6" (10 x 15 cm), by pushing it in all the way to the back of the
cassette.
147 
						

							6.Holding the right tab on the front cover, push the cassette back until the arrow () on the
front cover is aligned with the arrow (
) on the machine.
After pushing the cassette back, the paper information registration screen is displayed on the LCD.
7.
Select the size and type of the loaded paper in the cassette at  Page size and Type , then
press the  OK button.
If a message is displayed on the screen, follow the directions in the message to complete registration.
Paper setting for Printing
3.
Open the paper output tray.
1.
Extend the paper support (F), then open the output tray extension (G).
2.
Open the paper output tray (H) gently, then extend the paper output support (I).
148 
						

							Important
•
Be sure to open the paper output tray when printing. If not open, the machine cannot start printing.
Note
•
When printing, select the size and type of the loaded paper on the print settings screen of the operation
panel or printer driver.
149 
						

							Loading EnvelopesYou can load Envelope DL and Envelope Com 10.
The address is automatically rotated and printed according to the envelope's direction by specifying with the printer driver properly.
Important
•
Printing of envelopes from the operation panel or from a digital camera is not supported.
•
Do not use the following envelopes. They could jam in the machine or cause the machine to malfunction.
•
Envelopes with an embossed or treated surface
•
Envelopes with a double flap
•
Envelopes whose gummed flaps are already moistened and adhesive
1.
Prepare envelopes.
•
Press down on all four corners and edges of the envelopes to flatten them.
•
If the envelopes are curled, hold the opposite corners and gently twist them in the oppositedirection.
•
If the corner of the envelope flap is folded, flatten it.
•
Use a pen to press the leading edge in the inserting direction flat and sharpen the crease.
The figures above show a side view of the leading edge of the envelope.
Important
•
The envelopes may jam in the machine if they are not flat or the edges are not aligned. Make surethat no curl or puff exceeds 0.1 inch (3 mm).
2.
Load envelopes.
1.
Open the front cover gently.
150