Canon printer PIXMA MG5622 User Manual

							Don't detect mismatch of paper settings when printing from computerWhen you print documents from your computer and the paper settings on the printer driver and
the printer do not match, this setting disables the message display and allows you to continue
printing.
To disable detection of paper setting mismatches, select this check box.
Ink Drying Wait Time You can set the length of the printer rest time until printing of the next page begins. Moving the
slider to the right increases the pause time, and moving the slider to the left decreases the time.
If the paper gets stained because the next page is ejected before the ink on the printed page
dries, increase the ink drying wait time. Reducing the ink drying wait time speeds up printing.4.
Apply the settings
Click  OK and when the confirmation message appears, click  OK.
The printer operates with the modified settings hereafter.
221 
						

							Changing the Machine Settings on the LCD
Changing the Machine Settings on the LCD
Print settings
LAN settings
Device user settings
PictBridge print settings
Language selection
Firmware update
Cassette settings
Reset setting
About ECO settings
About Quiet setting
Using the Machine with the Access Point Mode
222 
						

							Changing the Machine Settings on the LCDThis section describes the procedure to change the settings in the  Device settings screen, taking the steps
to specify  Extended copy amount  as an example.1.
Make sure that the machine is turned on.
2.
Select  Setup  on the  HOME screen.
LCD and Operation Panel
3.
Select  Device settings , then press the OK button.
The  Device settings  screen is displayed.
4.
Use the  button to select the setting item, then press the  OK button.
The setting screen for the selected item is displayed.
5.
Use the  button to select the menu, then press the  OK button.
6.
Use the  button to select the setting item, then press the  OK button.
223 
						

							You can select the setting menus below.
Print settings
LAN settings
Device user settings
PictBridge print settings
Language selection
Firmware update
Cassette settings
Reset setting
Note
•
You can use the machine considering the environment, such as setting 2-sided printing as default orenabling the machine to turn on/off automatically.
About ECO settings
•
You can reduce the operating noise when printing at night.
About Quiet setting
224 
						

							Print settings•
Prevent paper abrasion
Use this setting only if the print surface becomes smudged.
Important
•
Be sure to set this back to  OFF after printing since it may result in lower printing speed or lower
print quality.
•
Extended copy amount
Selects the amount of image that extends off the paper when printing in borderless (full). Slight cropping may occur at the edges since the copied image is enlarged to fill the whole page. You
can change the width to be cropped from the borders of the original image as needed.
Cropped area will be larger if  Extended amount: Large is selected.
Important
•
This setting can be applied under the following conditions:
- Performing borderless copying
- Borderless is selected for Border when copying printed photos
Note
•
If printouts contain margins even though you are printing in Borderless, specifying  Extended
amount: Large  for this setting may help solve the problem.
•
Auto photo fix setting
When  ON is selected, you can select whether to print photos using the Exif information recorded in the
image files when  Default* or On is selected in printing with a PictBridge (Wireless LAN) compliant
device.
* When  Default is selected for the print setting on the PictBridge (Wireless LAN) compliant device,
select  Auto photo fix  for Photo fix  in PictBridge print settings .
•
Prevent paper double-feed
Select  ON to prevent double-feed of plain paper.
Important
•
Select  ON only when double-feed of plain paper occurs.
•
Adjust horizontal print position
Adjusts the print position when the left/right margins are not aligned.
You can adjust the left/right margins in increments of 0.003 inches/0.1 mm between -0.1 inches/-3 mm
and +0.1 inches/+3 mm centered on the horizontal center of the paper.
Important
•
For Letter-sized or Legal-sized paper, you can adjust the left/right margins between -0.05 inches/-1.5 mm and +0.05 inches/+1.5 mm even if you specify the value over 0.05 inches/1.5 mm.
225 
						

							LAN settings•
Change LAN
Enables either wireless LAN or access point mode. You can also disable wireless LAN or access point
mode.
•
Wireless LAN setup
Selects the setup method for wireless LAN connection.
Note
•
You can also enter this setting menu by selecting  WLAN on the  HOME screen. In this case, enable
wireless LAN.
When this menu is selected, the machine starts searching for a WPS-compatible access point. If the
machine detects the access point, follow the on-screen instructions to set up wireless LAN. If an access
point is not detected or if you select another setup method, select one of the setup methods below.
◦
Standard setup
Select when you perform settings for wireless LAN manually using the operation panel of the machine.
◦
WPS (Push button method)
Select when you perform settings for wireless LAN using an access point supporting a Wi-Fi Protected Setup (WPS) push button method. Follow the on-screen instructions during setup.
◦
Other setup
Advanced setup Select when you perform settings for wireless LAN manually. You can specify multiple WEP
keys.
WPS (PIN code method) Select when you perform settings for wireless LAN using an access point supporting a Wi-Fi
Protected Setup (WPS) PIN code method. Follow the on-screen instructions during setup.
Cableless setup Select if you specify the settings of the access point information to the machine directly from adevice (such as a smartphone) without operating the access point. Follow the on-screen
instructions of the connecting device for the setup procedure.
•
Confirm LAN settings
The list of wireless LAN settings or the access point mode of this machine is displayed on the LCD. You can print the list from this setting menu.
◦
WLAN setting list
The list of wireless LAN settings of this machine is displayed on the LCD. The following setting items are displayed.
ItemsSettingConnectionActive/InactiveSSIDXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXX
226 
						

							Communication modeInfrastructureChannelXXWireless LAN securityInactive/WEP(64bit)/WEP(128bit)/WPA-PSK(TKIP)/WPA-PSK(AES)/WPA2-PSK(TKIP)/WPA2-PSK(AES)IPv4 addressXXX. XXX. XXX. XXXIPv4 subnet maskXXX. XXX. XXX. XXXIPv4 default gatewayXXX. XXX. XXX. XXXIPv6 addressXXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXXIPv6 subnet prefix lengthXXXIPv6 default gatewayXXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXXMAC addressXX:XX:XX:XX:XX:XXIPsec settingsEnable (ESP)/Enable (ESP & AH)/Enable (AH)/DisablePre-shared keyXXXXXXXXXXXXXXXXPrinter nameXXXXXXXXXXXXXXXBonjour service nameXXXXXXXXXXXXX
XXXXXXXXXXXXX
XXXXXXXXXXXXX
XXXXXXXXXXXXX
("XX" represents alphanumeric characters.)
◦
AP mode setting list
The list of access point mode settings of this machine is displayed on the LCD. The following setting items are displayed.
ItemsSettingConnectionActive/InactiveSSIDXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXPasswordXXXXXXXXXXCommunication modeAccess point modeChannel3Wireless LAN securityInactive/WPA2-PSK(AES)IPv4 addressXXX. XXX. XXX. XXXIPv4 subnet maskXXX. XXX. XXX. XXX
227 
						

							IPv4 default gatewayXXX. XXX. XXX. XXXIPv6 addressXXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXXIPv6 subnet prefix lengthXXXIPv6 default gatewayXXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXXMAC addressXX:XX:XX:XX:XX:XXIPsec settingsDisablePre-shared keyXXXXXXXXXXXXXXXXPrinter nameXXXXXXXXXXXXXXXBonjour service nameXXXXXXXXXXXXX
XXXXXXXXXXXXX
XXXXXXXXXXXXX
XXXXXXXXXXXXX
("XX" represents alphanumeric characters.)
◦
Print LAN details
You can print out the network settings of the machine such as its IP address and SSID.
For more information on the machine's network setting is printed out:
Printing Out Network Setting Information
Important
•
This printout contains valuable information about your computer. Handle it with care.
•
Other settings
Important
•
You cannot select the items below when  Disable LAN is selected for  Change LAN.
◦
Set printer name
Specifies the printer name. You can use up to 15 characters for the name.
Note
•
You cannot use the same printer name as that already used for other LAN connected devices.
•
You cannot use a hyphen for the initial or last character of the printer name.
◦
TCP/IP settings
Performs IPv4 or IPv6 setting.
◦
WSD setting
Setting items when you use WSD (one of the network protocols supported in Windows 8.1,
Windows 8, Windows 7, and Windows Vista).
Enable/disable WSD Selects whether WSD is enabled or disabled.
228 
						

							Note•
When this setting is enabled, the printer icon is displayed on the Network Explorer in Windows
8.1, Windows 8, Windows 7 and Windows Vista.
WSD scan from this device Selecting  Enable allows you to transfer the scanned data to the computer using WSD.
Timeout setting Specifies the timeout length.
◦
Bonjour settings
Setting items for LAN using Bonjour for Mac OS.
Enable/disable Bonjour Selecting  Enable allows you to use Bonjour to perform the network settings.
Service name Specifies the Bonjour service name. You can use up to 48 characters for the name.
Note
•
You cannot use the same service name as that already used for other LAN connected devices.
◦
LPR protocol setting
Activates/deactivates the LPR setting.
◦
PictBridge communication
Setting items for printing from a PictBridge (Wireless LAN) compliant device. Enable/disable communication Selecting  Enable allows you to print from a PictBridge (Wireless LAN) compliant device.
Timeout setting Specifies the timeout length.
◦
Wireless LAN DRX setting
Selecting  Enable allows you to activate discontinuous reception when using wireless LAN. It allows
you to save electricity.
Note
•
Depending on the access point you are using, discontinuous reception may not be activated even though  Enable is selected.
•
Discontinuous reception is activated only while the machine is on standby. (The LCD is in the
screen saver mode.)
◦
Access point mode settings
When you use the machine as an access point, specify the access point name and the security
setting.
Using the Machine with the Access Point Mode
229 
						

							Device user settings•
Date display format
Changes the display format of dates when printed.
•
Key repeat
Enables/Disables continuous input by pressing and holding down the 
, , , ,  + , or  - button when
setting the number of copies, changing the photo displayed on the LCD, setting the zoom ratio, etc.
•
Device info sending setting
Selects whether you will send the printer usage information to Canon server. The information sent to
Canon will be utilized to develop better products. Select  Agree to send the printer usage information to
Canon server.
230