Canon printer PIXMA MG5622 User Manual

							Printing AreaTo ensure the best print quality, the machine allows a margin along each edge of media. The actual
printable area will be the area inside these margins.
Recommended printing area 
 : Canon recommends that you print within this area.
Printable area 
 : The area where it is possible to print. However, printing in this area can affect the print
quality or the paper feed precision.
Note
•
With performing Automatic Duplex Printing and Duplex (Two-sided) Copying, the printable area will be 0.08 inch (2 mm) smaller at the top margin.
•
When performing borderless copying or borderless printing from a printed photo, select  Extended copy
amount  in Print settings  of Device settings  to specify the amount of images that extends off the
paper.
Print settings
•
By selecting Borderless Printing option, you can make prints with no margins.
•
When performing Borderless Printing, slight cropping may occur at the edges since the printed image is enlarged to fill the whole page.
•
For Borderless Printing, use the following paper:
•
Photo Paper Pro Platinum 
•
Glossy Photo Paper "Everyday Use" 
•
Photo Paper Glossy 
•
Photo Paper Plus Glossy II 
•
Photo Paper Pro Luster 
•
Photo Paper Plus Semi-gloss 
•
Matte Photo Paper 
Performing Borderless Printing on any other type of paper may substantially reduce printing quality
and/or result in printouts with altered color hues.
Borderless Printing on plain paper may result in printouts with reduced quality. Use them only for test printing. Borderless Printing onto plain paper from the operation panel or from a digital camera is not
supported.
•
Borderless Printing is not available for legal, A5, or B5 sized paper, or envelopes.
•
Depending on the type of paper, Borderless Printing may reduce the print quality at the top and bottom edges of the paper or cause these parts to become smudged.
161 
						

							Other Sizes than Letter, Legal, EnvelopesSizePrintable Area (width x height)A55.56 x 7.95 inches (141.2 x 202.0 mm)A48.00 x 11.38 inches (203.2 x 289.0 mm)B56.90 x 9.80 inches (175.2 x 249.0 mm)4" x 6" (10 x 15 cm)3.73 x 5.69 inches (94.8 x 144.4 mm)5" x 7" (13 x 18 cm)4.73 x 6.69 inches (120.2 x 169.8 mm)8" x 10" (20 x 25 cm)7.73 x 9.69 inches (196.4 x 246.0 mm)
 Recommended printing area
(A) 1.70 inches (43.3 mm)
(B) 1.47 inches (37.4 mm)
 Printable area
(C) 0.12 inch (3.0 mm)
(D) 0.20 inch (5.0 mm)
(E) 0.13 inch (3.4 mm)
(F) 0.13 inch (3.4 mm)
162 
						

							Letter, LegalSizePrintable Area (width x height)Letter8.00 x 10.69 inches (203.2 x 271.4 mm)Legal8.00 x 13.69 inches (203.2 x 347.6 mm)
 Recommended printing area
(A) 1.70 inches (43.3 mm)
(B) 1.47 inches (37.4 mm)
 Printable area
(C) 0.12 inch (3.0 mm)
(D) 0.20 inch (5.0 mm)
(E) 0.25 inch (6.4 mm)
(F) 0.25 inch (6.3 mm)
163 
						

							EnvelopesSizeRecommended Printing Area (width x height)Envelope DL3.88 x 7.06 inches (98.8 x 179.5 mm)Envelope Com 103.68 x 7.90 inches (93.5 x 200.8 mm)
 Recommended printing area
(A) 0.31 inch (8.0 mm)
(B) 1.28 inches (32.5 mm)
(C) 0.22 inch (5.6 mm)
(D) 0.22 inch (5.6 mm)
164 
						

							Loading Originals
Loading Originals on the Platen Glass
How to Load Originals for Each Function
Originals You Can Load
How to Detach / Attach the Document Cover
165 
						

							Loading Originals on the Platen Glass1.
Load an original on the platen glass.
1.
Open the document cover.
2.
Load the original WITH THE SIDE TO SCAN FACING DOWN on the platen glass.
Originals You Can Load
How to Load Originals for Each Function
Important
•
Be sure to observe the following when loading the original on the platen glass.
•
Do not place any objects weighing 4.4 lb (2.0 kg) or more on the platen glass.
•
Do not put any pressure of 4.4 lb (2.0 kg) or more on the platen glass, such as pressing down
the original.
Failure to observe the above may cause the scanner to malfunction or the platen glass to break.
2.
Close the document cover gently.
Important
•
After loading the original on the platen glass, be sure to close the document cover before starting to copy or scan.
166 
						

							How to Load Originals for Each FunctionLoad the original in the correct position according to the function to use. If you do not load the original
correctly, it may not be scanned properly.
Loading the Original to Be Aligned with the alignment mark •
Load originals to copy
•
In  Scan ,
◦
select  Auto scan  for Doc.type  to scan text documents, magazines, or newspapers
◦
select Document  or Photo  for Doc.type  and specify a standard size (A4, Letter, etc.) for  Scan
size  to scan originals
•
With a software application on a computer,
◦
scan text documents, magazines, or newspapers
◦
select a standard size (A4, Letter, etc.) to scan originals
Place the original WITH THE SIDE TO SCAN FACING DOWN on the platen glass and align it with the alignment mark 
. Portions placed on the diagonally striped area cannot be scanned.
Important
•
The machine cannot scan the striped area (A) (0.04 inch (1 mm) from the edges of the platen glass).
Loading Only One Original in the Center of the platen glass
•
Scan only one printed photo in  Photo copy
•
In Scan ,
◦
select  Auto scan  for Doc.type  to scan one printed photo, postcard, business card, or disc
167 
						

							◦select Photo for Doc.type  and specify  Auto scan for Scan size  to scan one original•
Scan one printed photo, postcard, business card, or disc with a software application on a computer
Place the original WITH THE SIDE TO SCAN FACING DOWN, with 0.4 inch (1 cm) or more space between the edges (diagonally striped area) of the platen glass. Portions placed on the diagonally striped
area cannot be scanned.
Loading Two or More Originals on the platen glass
•
Scan two or more printed photos in  Photo copy
•
In Scan ,
◦
select  Auto scan  for Doc.type  to scan two or more printed photos, postcards, or business cards
◦
select Photo for Doc.type  and specify  Auto multi scan  for Scan size  to scan two or more
originals
•
Scan two or more printed photos, postcards, or business cards with a software application on a computer
Place the originals WITH THE SIDE TO SCAN FACING DOWN. Allow 0.4 inch (1 cm) or more space
between the edges (diagonally striped area) of the platen glass and the originals, and between the
originals. Portions placed on the diagonally striped area cannot be scanned.
You can place up to 12 items.
(A) More than 0.4 inch (1 cm)
Note
•
The Skew Correction function automatically compensates for the originals placed at an angle of up to approximately 10 degrees. Slanted photos with a long edge of 7.1 inches (180 mm) or more cannot
be corrected.
•
Non-rectangular or irregular shaped photos (such as cut out photos) may not be scanned properly.
168 
						

							Originals You Can LoadItemDetailsTypes of originals- Text document, magazine, or newspaper
- Printed photo, postcard, business card, or disc (BD/DVD/CD, etc.)Size (width x height)Max. 8.5 x 11.7 inches (216 x 297 mm)
Note
•
When loading a thick original such as a book on the platen glass, you can load it by removing the document cover from the machine.
How to Detach / Attach the Document Cover
169 
						

							How to Detach / Attach the Document CoverDetaching the document cover:Hold up the document cover vertically and then tip it back.
Attaching the document cover: Fit both hinges (A) of the document cover into the holder (B) and insert both hinges of the document cover
vertically as illustrated below.
170