Oce PlotWave 300 User Manual

							FunctionSettings valuesSetting
The width of the original is automatically
detected by the scanner.
'Auto''Width detect'
The width of the original is a standard
size.
Note:
Depend on the media series you
defined in the Océ Express
WebTools
'Standard'
Available standard sizes:
■'A0'
'A1'
'A2'
'A3'
'E+ (36")'
'B1 (707 mm)'
'B2 (19.69 in)'
The width of the original is a custom size.'Custom'
You can enter a size
within the range of 210
to 914 mm.
Settings group: 'Media'
#
FunctionSettings valuesSetting
Define the media feed to copy or print
on. When you select 'Auto' the printer
automatically selects the media roll.
'Auto'
'Roll 1' (description of
media type and media
size loaded on roll 1)
'Roll 2' (description of
media type and media
size loaded on roll 2)
'Manual'
Chapter 5 - Use the printing system
181
Available settings for copy jobs
Downloaded From ManualsPrinter.com Manuals 
						

							Settings group: 'Scale'
#
FunctionSettings valuesSetting
Scales the image to the original size.'1:1''1:1'
Scales the image to fit the selected media
size.
Note:
Depends on the media series you
defined in the Océ Express
WebTools
'A0'
'A1'
'A2'
'A3'
'E+ (36")'
'B1 (707 mm)'
'B2 (19.69 in)'
'To fit'
Scales the image to a custom percentage.10 - 1000'%''Custom'
Settings group: 'Delivery'
#
FunctionSettings valuesSetting
The location to deposit the sheet face-
down.
Note:
Not all media types can be deliv-
ered to the Top delivery tray.
'Top Delivery
Tray'
Chapter 5 - Use the printing system
182
Available settings for copy jobs
Downloaded From ManualsPrinter.com Manuals 
						

							FunctionSettings valuesSetting
The location to deposit the sheet face-up.'Back output'
Settings group: 'Sheet size'
#
FunctionSettings valuesSetting
'Determines the cut size of the print.
'Standard': the print is cut to a standard
media size (DIN, ANSI, ...). 'Synchro':
the print length depends on the image.'
'Synchro'
'Standard'
'Cut method'
'Adds a blank strip at the beginning of
the output.'
0 to 400 mm'Add leading
strip'
'Adds a blank strip at the bottom of the
output.'
0 to 400 mm'Add trailing
strip'
Chapter 5 - Use the printing system
183
Available settings for copy jobs
Downloaded From ManualsPrinter.com Manuals 
						

							Settings group: 'Positioning'
#
FunctionSettings valuesSetting
'Aligns the image on the media.''Top left'
'Top'
'Top right'
'Left'
'Center'
'Right'
'Bottom left'
'Bottom'
'Bottom right'
'Alignment'
'Shifts the image in the horizontal direc-
tion (after alignment to one of the posi-
tions given in 'Alignment').'
- 914 mm to + 914 mm'Shift horizon-
tal'
'Shifts the image in the vertical direction
(after alignment to one of positions given
in 'Alignment').'
- 1219 mm to + 1219
mm
'Shift vertical'
Settings group: 'Erase margins'
#
FunctionSettings valuesSetting
'Erase a strip from the beginning of the
original.'
0 to 400 mm'Top'
Chapter 5 - Use the printing system
184
Available settings for copy jobs
Downloaded From ManualsPrinter.com Manuals 
						

							FunctionSettings valuesSetting
'Erase a strip from the bottom of the
original.'
0 to 400 mm'Bottom'
'Erase a strip from the left side of the
original.'
0 to 914 mm'Left'
'Erase a strip from the right side of the
original.'
0 to 914 mm'Right'
Settings group: 'Erase area'
#
FunctionSettings valuesSetting
'The horizontal offset where the erase area
starts.'
0 to 914 mm'Hor offset'
Chapter 5 - Use the printing system
185
Available settings for copy jobs
Downloaded From ManualsPrinter.com Manuals 
						

							FunctionSettings valuesSetting
'The vertical offset where the erase area
starts.'
0 to 6000 mm'Vert offset'
'The width of the area to erase.'0 to 914 mm'Width'
'The length of the area to erase.'0 to 6000 mm'Length'
Settings group: 'Stamp'
#
FunctionSettings valuesSetting
Copy with a stampNone
------
'Stamp'
'The position of the stamp inside the leg-
end.'
'Top'
'Middle'
'Bottom'
'Position'
Chapter 5 - Use the printing system
186
Available settings for copy jobs
Downloaded From ManualsPrinter.com Manuals 
						

							FunctionSettings valuesSetting
'The size of the stamp.''Small'
'Large'
'Size'
'The color of the stamp.''Light gray'
'Gray'
'Dark gray'
'Black'
'Color'
Settings group: 'Drawing method'
#
FunctionSettings valuesSetting
Defines which drawing method is used
for the legend position.
'DIN'
'Afnor'
'Ericsson'
'Method'
'Defines whether the legend is located at
the top (leading) or the bottom (trailing).'
'Top'
'Bottom'
'Legend'
Chapter 5 - Use the printing system
187
Available settings for copy jobs
Downloaded From ManualsPrinter.com Manuals 
						

							Settings group: 'Light and mirror'
#
FunctionSettings valuesSetting
Increase the value for lighter prints; de-
crease for darker prints.
-5 to +5'Lighter/dark-
er'
'When 'on', the image is mirrored along
the vertical axis (the media transport di-
rection).'
'On'
'Off'
'Mirror'
Settings group: 'Sort'
#
FunctionSettings valuesSetting
If you want to copy multiple sheets, you
can indicate how the copied sheets must
be sorted.
'By page'
'By set'
'Sort'
Chapter 5 - Use the printing system
188
Available settings for copy jobs
Downloaded From ManualsPrinter.com Manuals 
						

							Make multiple sets of copies
Introduction
You can use the 'Create set' option to make multiple sets of copies.
Before you begin
If you must enter the same value for a setting very often, you can set this value as the de-
fault value for that setting in the Océ Express WebTools.
After you press the start key, the user panel always shows the job number and status of
the job. A copy job appears temporarily in the 'Jobs - Queue' section of the Océ Express
WebTools, a scan job appears in the Smart Inbox 'Scans'.
How to make multiple sets of copies sorted by set
1.Feed the original face up and centered on the original feeding table.
Note:
You do not need to center the original precisely. The exact position of the original is au-
tomatically detected by the scanner.
The 'Copy' tab is automatically activated on the user panel.
2.Open the 'Copy' tab with the confirmation button above the scroll wheel.
3.Define the job settings.
■Open a template with the confirmation button.
The 'Create set' option appears at the lower left corner of the screen.
■Select 'Create set' with the lower left soft key.
The 'Close set' option appears at the lower left corner of the screen.
■Scroll to 'Sort', define 'By set' and confirm with the with confirmation button. This
setting is disabled after you press the green button for the first time.
■Press'OK'.
■Change the settings for your first original if necessary.
■Define the number of copies and press the green button.
You can not change the number of copies after you press the green button for the first
time.
Chapter 5 - Use the printing system
189
Make multiple sets of copies
Downloaded From ManualsPrinter.com Manuals 
						

							■Feed the next original, define the settings for this original if necessary and press the
green button.
You can use the lower right soft key to return to the default settings of your copy
template.
Repeat this step until all originals are fed.
4.Select 'Close set' with the lower left soft key.
How to make multiple sets of copies sorted by page
1.Feed the first original face up.
The scanner takes the original.
2.Open the 'Copy' tab with the confirmation button above the scroll wheel.
3.Define the job settings.
■Open a template with the confirmation button.
The 'Create set' option appears at the lower left corner of the screen.
■Select 'Create set' with the lower left soft key.
The 'Close set' option appears at the lower left corner of the screen.
■Scroll to 'Sort', define 'By page' and confirm with the with confirmation button. This
setting is disabled after you press the green button for the first time.
■Press'OK'.
■Change the settings for your first original if necessary.
■Define the number of copies and press the green button.
You can not change the number of copies after you press the green button for the first
time.
■Feed the next original, define the settings for this original if necessary and press the
green button.
You can use the lower right soft key to return to the default settings of your copy
template.
Repeat this step until all originals are fed.
4.Select 'Close set' with the lower left soft key.
Result
The Océ PlotWave 300 copies a set of originals sorted by set or by page.
Chapter 5 - Use the printing system
190
Make multiple sets of copies
Downloaded From ManualsPrinter.com Manuals