Oce PlotWave 300 User Manual

							2.Switch off the power switch at the rear side of the printing system (A).
Chapter 6 - Maintain the printing system
231
Switch off the printing system
Downloaded From ManualsPrinter.com ManualsA
B       
						

							Disconnect the network cable and the mains supply cable
Attention:
Make sure the main power switch (A) is in 'off' position.
1.Disconnect the network cable from the network connection at the back of the printer (at
the right).
2.Disconnect the 'Power' cable form the wall socket.
3.Disconnect the other side of the 'Power' cable from the power connection at the back of
the printer (B) (on the left).
Chapter 6 - Maintain the printing system
232
Disconnect the network cable and the mains supply cable
Downloaded From ManualsPrinter.com ManualsA
B       
						

							Move and re-adjust the printing system
Introduction
When you move the printing system to a new location you must check if it needs re-ad-
justment to ensure the best output quality.
You need two tools for the adjustment procedure. You can find these tools behind the
lower right front cover (11).
Required tool
■Allen wrench
■Key wrench
Attention:
If connected you must first switch off and disconnect the Océ PlotWave 300. (see ‘Switch
off the printing system’ on page 230 and ‘Disconnect the network cable and the mains supply
cable’ on page 232).
Chapter 6 - Maintain the printing system
233
Move and re-adjust the printing system
Downloaded From ManualsPrinter.com Manuals8
1
2
3
4
9
10
11
12
675   
						

							Attention:
Close the media drawers.
Note:
Be aware of the printer working area. (see ‘Working area [Footprint]’ on page 21).
1.Move the printing system to its new location.
2.Pull firmly to open the media drawer.
Chapter 6 - Maintain the printing system
234
Move and re-adjust the printing system
Downloaded From ManualsPrinter.com Manuals   
						

							3.Slide the lower left front cover (1) to remove it.
4.Check if the level indicator arrow is exactly on the middle of the marker.
If no, continue with step 5.
If yes, continue with step 9.
Chapter 6 - Maintain the printing system
235
Move and re-adjust the printing system
Downloaded From ManualsPrinter.com Manuals                    
						

							5.Slide up the lower right front cover (11) to remove it and get access to the tools you need
for the adjustment procedure.
6.Loosen the nut with the key wrench.
Chapter 6 - Maintain the printing system
236
Move and re-adjust the printing system
Downloaded From ManualsPrinter.com Manuals     
						

							7.Use the Allen wrench to adjust the level until the level indicator arrow is exactly on the
middle of the marker.
8.Lock the nut with the key wrench.
Chapter 6 - Maintain the printing system
237
Move and re-adjust the printing system
Downloaded From ManualsPrinter.com Manuals     
						

							9.Replace the lower left front cover.
10.Replace the tools and replace the lower right front cover.
Chapter 6 - Maintain the printing system
238
Move and re-adjust the printing system
Downloaded From ManualsPrinter.com Manuals     
						

							11.Close the media drawer.
Chapter 6 - Maintain the printing system
239
Move and re-adjust the printing system
Downloaded From ManualsPrinter.com Manuals   
						

							Connect the mains supply cable and the network cable
Attention:
Make sure the green power switch(B) is in 'off' position.
1.Plug in the mains supply cable at the power connection at the back of the printer (A) (on
the left).
2.Plug the other side of the mains supply cable into the wall socket.
3.Plug in the network cable at the bottom network connection at the back of the printer
(at the right) to connect the Océ PlotWave 300 to your company network.
Chapter 6 - Maintain the printing system
240
Connect the mains supply cable and the network cable
Downloaded From ManualsPrinter.com ManualsA
B