Oce PlotWave 300 User Manual

							3.Pull the handle of the roll holder locking mechanism towards you (1) and slide (2) the
roll holder into the right side of the core of the new media roll.
4.Align the roll with the center of the correct size indicator on the roll holder and release
the handle of the locking mechanism.
Chapter 6 - Maintain the printing system
251
Load a media roll (position 1)
Downloaded From ManualsPrinter.com Manuals1
2     
						

							Note:
If you use a B1 media size (707 mm) you must align the media roll with the A1 indent.
5.Remove the tapes from the new media roll and use both hands (as indicated) to place the
media roll in the media drawer.
Chapter 6 - Maintain the printing system
252
Load a media roll (position 1)
Downloaded From ManualsPrinter.com Manuals     
						

							6.Use both hands to turn the media roll backwards (1) until the media flap has passed the
metal paper guide.
7.Use both hands to slide the media under the metal paper guide (2) until the media is
transported automatically.
Chapter 6 - Maintain the printing system
253
Load a media roll (position 1)
Downloaded From ManualsPrinter.com Manuals1      2       
						

							8.If necessary, press the clean cut button to trim a strip of the new media roll. Press once
for a strip of approximately 20 cm or hold the button and release it when the strip has
the desired length.
9.Close the media drawer.
Note:
Do not open the 'Media drawer' during loading.
10.The user panel displays the message 'New media detected on roll 1' or 'New media de-
tected on roll 2'. Follow the steps in the wizard to define the correct media type. The
media size is detected automatically.
Chapter 6 - Maintain the printing system
254
Load a media roll (position 1)
Downloaded From ManualsPrinter.com Manuals   
						

							Load a media roll (position 2)
Note:
When your printing system is equipped with an additional second media roll, it is advised
to load an A0 or E-size media roll on position 1 and an A2 or C-size media roll on posi-
tion 2.
Caution:
Watch your fingers when you handle the media roll.
Caution:
If you want to load an A0 media roll on position 2, you must make sure to bend your
knees, as indicated below, to spare your back.
Chapter 6 - Maintain the printing system
255
Load a media roll (position 2)
Downloaded From ManualsPrinter.com Manuals 
						

							Illustration
How to load a media roll on position 2
1.Pull firmly to open the media drawer.
2.Place the new media roll on the roll loading station.
Chapter 6 - Maintain the printing system
256
Load a media roll (position 2)
Downloaded From ManualsPrinter.com Manuals     
						

							3.Pull the handle of the roll holder locking mechanism towards you (1) and slide (2) the
roll holder into the right side of the core of the new media roll.
4.Align the roll with the center of the correct size indicator on the roll holder and release
the handle of the locking mechanism.
Chapter 6 - Maintain the printing system
257
Load a media roll (position 2)
Downloaded From ManualsPrinter.com Manuals1
2     
						

							Note:
If you use a B1 media size (707 mm) you must align the media roll with the A1 indent.
5.Remove the tapes from the new media roll and use both hands (as indicated) to place the
media roll in the media drawer.
Chapter 6 - Maintain the printing system
258
Load a media roll (position 2)
Downloaded From ManualsPrinter.com Manuals     
						

							6.Use both hands to turn the media roll backwards (1) until the media flap has passed the
metal paper guide.
7.Use both hands to slide the media under the metal paper guide (2) until the media is
transported automatically.
Chapter 6 - Maintain the printing system
259
Load a media roll (position 2)
Downloaded From ManualsPrinter.com Manuals1  2   
						

							8.If necessary, press the clean cut button to trim a strip of the new media roll. Press once
for a strip of approximately 20 cm or hold the button and release it when the strip has
the desired length.
9.Close the media drawer.
Note:
Do not open the 'Media drawer' during loading.
10.The user panel displays the message 'New media detected on roll 1' or 'New media de-
tected on roll 2'. Follow the steps in the wizard to define the correct media type. The
media size is detected automatically.
Chapter 6 - Maintain the printing system
260
Load a media roll (position 2)
Downloaded From ManualsPrinter.com Manuals