Oce PlotWave 300 User Manual

							Switch on the printing system
Attention:
Make sure the mains supply cable (A) is plugged in.
1.Switch on the power switch at the rear side of the printing system (B).
2.Use the on / off button at the front side of the printer to switch on the printing system.
Chapter 6 - Maintain the printing system
241
Switch on the printing system
Downloaded From ManualsPrinter.com ManualsA
B       
						

							Note:
You can also use the 'Shut down' button in the Océ Express WebTools.
Chapter 6 - Maintain the printing system
242
Switch on the printing system
Downloaded From ManualsPrinter.com Manuals        
						

							Replace the media
The media drawer
Illustration
Component - function table
#
Description / FunctionComponentNr
Carries the media rollroll holder1
media roll 12
media roll 2 (optional)3
Groove integrated behind the front cover
of the media drawer.
roll loading station4
This button is used to trim a strip of a new
or damaged media roll.
clean cut button5
Chapter 6 - Maintain the printing system
243
The media drawer
Downloaded From ManualsPrinter.com Manuals1
2
35
4   
						

							Remove a media roll
Attention:
Handle the media roll with care. A dented media roll can damage the printer.
Attention:
Do not open the media drawer during the print process.
Caution:
Watch your fingers when you handle the media roll.
Caution:
If you want to remove an A0 media roll from position 2, you must make sure to bend
your knees, as indicated below, to spare your back.
Chapter 6 - Maintain the printing system
244
Remove a media roll
Downloaded From ManualsPrinter.com Manuals 
						

							Illustration
How to remove a media roll
1.Pull firmly to open the media drawer.
Chapter 6 - Maintain the printing system
245
Remove a media roll
Downloaded From ManualsPrinter.com Manuals     
						

							2.Roll back the media manually to remove the media from the metal paper guide.
3.Use both hands (as indicated) to lift the roll holder with the media roll and put it on the
roll loading station.
Chapter 6 - Maintain the printing system
246
Remove a media roll
Downloaded From ManualsPrinter.com Manuals1           
						

							4.Pull the handle of the roll holder locking mechanism towards you and remove the roll
holder from the core of the media roll.
5.Remove the media roll from the roll loading station.
Chapter 6 - Maintain the printing system
247
Remove a media roll
Downloaded From ManualsPrinter.com Manuals1
2   
						

							Unpack the media roll
Attention:
Handle the media roll with care. A dented media roll can damage the printer.
Attention:
Please refer to the list of ‘Preferred Océ media types and sizes’ on page 316 to find the corre-
sponding media name that you must select on your user panel.
Attention:
Always write the correct media name inside the core, after you unpack the media roll. In
that case, if you replace a media roll before it is empty and you want to re-use it later,
you will have the correct media information available.
1.Place the media box on a table and open it.
Chapter 6 - Maintain the printing system
248
Unpack the media roll
Downloaded From ManualsPrinter.com Manuals 
						

							2.Remove the plug from the media roll.
3.Carefully remove the media roll from the box.
4.Remove the other plug and plastic around the media roll.
Chapter 6 - Maintain the printing system
249
Unpack the media roll
Downloaded From ManualsPrinter.com Manuals 
						

							Load a media roll (position 1)
Note:
When your printing system is equipped with an additional second media roll, it is advised
to load an A0 or E-size media roll on position 1 and an A2 or C-size media roll on posi-
tion 2.
Caution:
Watch your fingers when you handle the media roll.
How to load a media roll on position 1
1.Pull firmly to open the media drawer.
2.Place the new media roll on the roll loading station.
Chapter 6 - Maintain the printing system
250
Load a media roll (position 1)
Downloaded From ManualsPrinter.com Manuals