GTE Omni Scbs Installation And Maintenance Manual

							-+ 
0 0 0 0 
w liiiirl 
t- t- 
-t -+ -t -+ 
Iis- -+ Jl 0 
II - .I  
						

							eview Exercis 
s 
8. COMPLETE THE FOLLOWING DIAGRAMS INDICATING THE CROSS CONNECTIONS THAT WERE 
MADE FOR THE EIGHT TRUNKS THAT WERE INSTALLED (POWER FAIL, CO, LOOP TIE LINES, AND 
E&M TIE LINES). 
CABLE 10 
CABLE 11 - - 
- - 
- - 
- - 
- - 
- - 
- - 
- - 
- - 
- - 
- - 
- - 
- - 
- - 
- - 
- - 
1.83 CABLE 12 14 - - 
40 - - 
:: I I 
16 - _ 
42 - _ 
17 - - 
43- - 
I8 - - 
44- - 
19 - - 
45- - 
20 - _ 
46- - 
21 - - 
47 - _ 
22 - _ 
.l8- - 
23 - - 
49 
24 I 1 
50 - _ 
, 25 - _ 
- - 
- - 
- - 
- - 
- -  
						

							Review Exercise (1.3) - Peripheral 
lation (Continued) 
9. THE PMP MAY BE CONNECTED TO EITHER OMNI SBCS PORT 
OR . 
10. BEFORE THE FLOPPY DISKETTE DRIVE MAY BE INSTALLED, THE PMP REQUIRES THAT 
ADDITIONAL 
MUST FIRST BE INSTALLED. 
11. MATCH THE FOLLOWING TYPES OF CABLES TO THEIR APPROPRIATE CONNECTIONS: 
# 715 
(A) FLOPPY DISKETTE DRIVE UNIT TO PMP 
# 707 (B) PMP TO OMNI SBCS PORT 
12. THE SMDR PRINTER IS INSTALLED IN WHAT OMNI SBCS PORT? 
OPTIONAL PERIPHERAL QUESTIONS (NIGHT BELL AND MUSIC-ON-HOLD INSTALLATION) 
13. NIGHT BELL INSTALLATION REQUIRES 
WIRES, CROSS CONNECTED TO A 
INTERFACE CARD. 
14. MUSIC-ON-HOLD USING A CUSTOMER-PROVIDED MUSIC SOURCE REQUIRES 
WIRES, CROSS CONNECTED TO A 
INTERFACE CARD. 
1.84  
						

							Student Notes 
1.85  
						

							. . 
SYSTEM INSTALLATION 
Start Up and 
Initialization 
1.66  
						

							1.4 Enabling Objective/Start Up and 
GIVEN: 0 
0 
0 
ACTION: 0 
0 
0 
CRITERIA: 0 
0 
INSTALLED GTE OMNI SBCS AND PERIPHERALS 
GTE OMNI SBCS COURSE AND SITE DOCUMENTATION 
PACKAGE 
REVIEW EXERCISE 
POWER ON SYSTEM AND PERFORM COLD RESTART 
TO INITIALIZE DEFAULT STANDARD DATA BASE. 
PERFORM SYSTEM OPERATION CHECKS. 
COMPLETE REVIEW EXERCISE. 
SYSTEM WILL BE INITIALIZED AND OPERATION WILL 
BE VERIFIED IN ACCORDANCE WITH GTE OMNI SBCS 
GTEP MANUAL. 
REVIEW EXERCISE QUESTIONS WILL BE COMPLETED 
CORRECTLY IN ACCORDANCE WITH PASS/FAIL 
CRITERIA OF THIS TRAINING ORGANIZATION. 
1.87  
						

							CPM Controls & Indicat 
GREEN LED SHOWS SYSTEM STATUS. 
NORMAL CONDITION IS ON. I C 
LA 
ALM (RED) LED INDICATES A MINOR 
ALARM. 
TO (RED) LED INDICATES A MAJOR 
ALARM. 
/ UP-COLD RESTART 
J CAUTION 
REESTABLISHES DEFAULT 
 DATA BASE ODDB IS LOST 
CENTER- COLD 
RESET MOMENTARY 
INTERRUPT 
(8 
HOT 
DOWN- 
HOT RESTART 
%b lo 0 
r 
- RUN (GREEN) 
- RESTART BUTTON 
1 
1.88 
I  
						

							System Initialization 
DESCRIPTION: 
. LOADS SYSTEM OPERATING PROGRAM AND DATA BASE MANAGEMENT PROGRAM FROM ROM TO WORKING ROM AND EPROM. 
@ INITIALIZES SYSTEM BY LOADING DEFAULT STANDARD DATA BASE AT TIME OF INSTALLATION. 
. REQUIRES THAT AT LEAT ONE LINE CARD AND ONE TRUNK CARD ARE SEATED IN CARD SLOTS FOR SYSTEM PROGRAMMING. 
. MUST BE PERFORMED WHENEVER CPM OR MEM CARDS ARE REPLACED. 
. MUST ALSO BE PERFORMED AFTER SERIOUS POWER OUTAGE WITH LOSS OF SYSTEM BATTERY BACKUP. 
PROCEDURE: 
(1) HOLD TOGGLE SWITCH ON CPM CARD IN UP POSITION WHILE SIMULTANEOUSLY PRESSING RESTART BUTTON. 
(2) RELEASE TOGGLE SWITCH BACK TO CENTER POSITION. 
HOT RESTART ~ 
Q, A ?, t, \“‘g 0 TV: \F ‘. ,-.*j % p k ,’ -..; “f z.1 (’ ‘. 
; 1, 6 
&’ b> .>‘. 1”(f-‘b .,-\i bfyp) r-j,T ~ / ;:. I @-! tic’, 
. 
[@ R “>‘iS ye,--, “9 +. i-i? 2 :: 0 :; I’( q > 
CONTROLS, BUT DOES NOT AFFECT CONTENTS OF RAM. 
l CALL PROCESSING CEASES. 
. ALL DATA BASE MODIFICATIONS IN CUSTOMIZED DATA BASE REMAIN. 
. SYSTEM AUTOMATICALLY INITIATES HOT RESTART DURING ITS RECOVERY FROM MAJOR POWER FAILURE. 
PROCEDURE: 
(1) 
(2) HOLD TOGGLE SWITCH ON CPM CARD IN DOWN POSITION WHILE Sl,MULTANEOUSLY PRESSING RESTART BUTTON. 
RELEASE TOGGLE SWITCH BACK TO CENTER POSITION. 
MANUAL RESET 
DESCRIPTION: 
. RECOVERS SYSTEM AND CALL PROCESSING FROM MOMENTARY POWER INTERRUPTION. 
l DOES NOT AFFECT CONTENTS OF RAM. 
l ALL DATA BASE MODIFICATIONS IN CUSTOMIZED DATA BASE REMAIN. 
l MUST BE PERFORMED WHENEVER LINE OR TRUNK CARDS ARE REPLACED. 
PROCEDURE: 
(1) ENSURE THAT TOGGLE SWITCH ON CPM CARD IS IN CENTER POSITION. 
(2) PUSH RESTART BUTTON. 
1.89  
						

							AFTER SYSTEM HAS BEEN lNlTlALlZED WITH A COLD RESTART AND 
PROGRAMMED ACCORDING TO CUSTOMER SPECIFICATIONS, PERFORM 
THE FOLLOWING CHECKS AS APPLICABLE: 
(1) TEST STATION INSTRUMENTS TO ENSURE THAT EACH IS 
OPERATING CORRECTLY. LISTEN FOR DIAL TONE, TEST FEATURE 
BUTTONS, AND VERIFY CAPABILITY TO MAKE STATION-TO-STATION 
CALLS AND TRUNK CALLS. 
(2) TEST PERSONAL LINES AND KEY SYSTEM TYPE LINES. 
(3) TEST SYSTEM ACCESS CODES. 
(4) TEST CLASSES OF RESTRICTION. 
(5) TEST LEAST COST ROUTING. 
(6) TEST SMDR PRINTER AND POWER FAULT TRANSFER, IF EQUIPPED. 
1.90  
						

							16’1