GTE Omni Scbs Installation And Maintenance Manual

							-. 
STATION ACCESS 
BUTTONS WITH 
LED LAMPS 
DSS 80 
III1211311411sl 270 271 272 . 273 274 275 276 277 278 279 
2.48  
						

							odules 
efault 
. ALLOWS FOR PREPROGRAMMED STATlON BUTTON ASSIGNMENTS ON BLFIDSS 
MODULE. 
@ BLF/DSSSHOULD BEASSIIGNEDTO ODD ClRCUlT NUMBER ON 8EKC CARD INSERTED 
lNT0 CARD SLOT 01. 
@ REQUlRES THAT CS-IO OR CS-20 ASSOClATED WITH BLFIDSS MUST BE INSTALLED 
AS A STATION ON SAME 8EKC CARD IN SLOT 01. ASSOCIATED EKT SHOULD BE 
CONNECTED TO THE EVEN NUMBERED CIRCUIT ONE NUMBER LESS THAN THE 
BLFIDSS CIRCUIT NUMBER (I.E., EKT = CIRCUIT 0, BLF/DSS = CIRCUIT 1). 
jl * 
(UTILIZING DEFAULT STANDARD DATA BASE SETTINGS) 
,’ 
@ COLD RESTART THE SYSTEM. ALL TRUNKS AND STATIONS WILL AUTOMATICALLY 
RECEIVE THE DEFAULT STANDARD DATA BASE SETTINGS. 
WARNING: DO NOT USE THIS PROCEDURE AFTER DATA BASE MODIFICATIONS HAVE 
BEEN MADE. A COLD RESTART DELETES ALL PREVIOUS DATA BASE CHANGES SINCE 
SYSTEM WILL REVERT TO DEFAULT STANDARD DATA BASE SETTINGS. 
*ASSUMES 8EKC CARD IS SEATED IN CARD SLOT 01 AND BLFIDSS IS PHYSICALLY 
CONNECTED TO APPROPRIATE CIRCUIT. 
2.49  
						

							BLF/DSS Instr 
allatio - Man 
. ASSUMES THAT COMPLETE PROGRAMMING OF BLF/DSS CONSOLE 
IS REQUIRED. 
0 PROCEDURE USED IF DEFAULT STANDARD DATA BASE IS NOT USED 
OR IF THE BLF/DSS IS NOT CONNECTED TO AN 8EKC CARD IN CARD 
SLOT 
Ol.* 
. THE CS-10 OR CS-20 ASSOCIATED WITH THE BLF/DSS MUST 
ALREADY BE INSTALLED PRIOR TO BLF/DSS INSTALLATION. 
I PROCEDURE I 
1. 
USE CMC-210 TO ASSIGN: 
. IDENTIFYING BLF/DSS INSTRUMENT NUMBER (Pl) 
. BLF/DSS TYPE (P2) 
. EQUIPMENT NUMBER (P3) 
* ASSOCIATED EKT STATION DIRECTORY NUMBER (P4) 
. COPIED BLF/DSS INSTRUMENT NUMBER (P5) 
. BLF/DSS ORDER** 
2. USE CMC-211 TO ASSIGN: 
. ASSOCIATED EKT STATION DIRECTORY NUMBER (Pl) 
. BLF/DSS BUTTON NUMBER (P2) 
. TYPE OF BLF/DSS FEATURE (P3) 
l STATION DIRECTORY NUMBER ASSIGNED TO BUTTON (P4) 
i LINE TERMINATION TYPE FOR LINE ACCESS WHEN I’3 = 9 (P5) 
0 RINGING MODE WHEN P3=9 (P6) 
*ASSUMES 8EKC CARD IS SEATED IN CARD SLOT 00 OR 02-14 AND 
BLF/DSS IS PHYSICALLY CONNECTED TO APPROPRIATE CIRCUIT. 
**PACKAGE C AVAILABILITY 
2.50 CMC= 210  CMC= 210 
Pl: i  Pl: i P4: 214  P4: 214 
P2: 1  P2: 1 
P3: 013  P3: 013 
CMC= 211 
Pl:214 . 
P2: 3 F541 
P3: 6 P6:  
						

							SS Instruments 
1 PROCEDURE 1 (CHANGE) 
C-211 TO RE VE Bls/D 
BUTTON 
ASSIGN T BEFORE 
ENTERING NEW BUTTON ASSlGNMENTS. 
8 USE CM@-2-M TO EMlOVE BLFIDSS ASSIGNMENT 
EXISTING ENTRIES MUST BE REMOVED BEFORE CHANGING 
BLWBSS MODULE ASSIGNMENTS. 
2.51  
						

							, .- 
,, -. 
Programming BLF/DSS Modules 
CMC Corn and Summary 
CATEGORY CMC TABLE 
@ BLF/DSS 210 
ASSIGNMENT 
8 BLFIDSS BUTTON 211 
ASSIGNMENT 
2.52 
FUNCTION 
ASSIGNS OR REMOVES 
BLF/DSS MODULES. 
ASSIGNS, REMOVES, OR 
CHANGES BLF/DSS 
FEATURE OR STATION 
INTERCOM BUTTONS FOR 
EACH BLF/DSS BUTTON.  
						

							PERFORM THE FOLLOWING PROGRAMMING TASKS IN THE SEQUENCE OUTLINED BELOW, USING THE SAMPLE WORK 
ORDERS AND IN ACCORDANCE WITH THE GTE OMI SBCS GTEP MANUAL. COMPLETE THE REVIEW EXERCISE QUESTIONS 
PERTAINING TO STATION AND BLF/DSS PROGRAMMING UPON COMPLETION OF THIS LABORATORY ACTIVITY. 
WORK ORDER #2.2 
IOMPANY NAME: NU SYSTEM CC. PHONE #: (703) 5551212 
-0CATtCN: RESTON, VIRGINIA WORK ORDER #2.2 (TASK #I) 
‘R’G’NAToR: TELECOMMUNICATIONS MANAGER 
-ASKS: 
- e Add, modify, or remove a station with CMC-200. 
e Assign station characteristics with CMC-201. 
(1) Install and add a CS-10 to card 01, circuit 0. 
(1) Perform programming changes for station 
(NOTE: Cross connect wiring was completed instruments. 
during installation. Simply connect station to 
modular jack, perform HOT Restart, and (2) HOT Restart system after installation. 
proceed with required programming. 
(3) Check/test the operation of changes after 
(2) Change default station directory number 
completion of this portion of the laboratory 
assignment from 208 to 308. 
(3) Assign station characteristics: 
Operation Mode = Bothway 
Type of Dialing = DTMF (4) Proceed to next work order task. ’ 
2.53  
						

							- Programming Station 
WORK ORDER #2.2 
ZOMPANY NAME: NU SYSTEM CO. 
-0CATlON: RESTON, VIRGINIA 
)RlGlNATOR: TELECOMMUNICATIONS MANAGER PHONE #: (703) 555-1212 
WORK ORDER #2.2 (TASK #2) 
-ASKS: 
l Restore station 215 to system by adding it with CMC-200. 
l Change station operation mode, tenant group, and SMDR metering 
group using CMC-201. 
‘ARAMETERS: INSTRUCTIONS: 
(1) Add station 215 at slot 01, circuit 07. (1) Perform programming changes for station 
instrument. 
(2) Change operation mode for SLT at slot 02, (2) Check/test the operation of changes after 
circuit 0 from bothway, to incoming only. completion of this portion of the laboratory 
activity. 
(3) Change dialing mode to DTMF for this 
instrument. (3) Proceed to next work order task. 
(4) Assign both SLT instruments to tenant group 1 
and metering group 10. 
NOTE: 
Programming of station tenant assignment, 
SMDR printer output, and station COSICOR 
assignments will be addressed in later 
laboratory activities. 
-- . 
‘_ 
2.54  
						

							boratory 
Instruments gramming Station 
WORK ORDER #2.2 
COMPANY NAME: NU SYSTEM CO. PHONE #: (703) 5551212 
-0CATION: RESTON, VIRGINIA WORK ORDER #2.2 
(TASK #3) 
I)RIGINATOR: TELECOMMUNICATIONS MANAGER 
I-ASKS: 
e Identify a station directory number as a data secure line or an 
off-premises extension with CMC-204. 
(1) Make station 214 a data secure line. (1) Perform programming changes for station 
instruments. 
(2) Designate the SLT at slot 02, circuit 7 as an off- 
premises extension. (2) Check/test the operation of changes after 
completion of this portion of the laboratory 
(3) Proceed to next work order task. 
2.55  
						

							WORK ORDER #2.2 
ZOMPANY NAME NU SYSTEM CO. 
-0CATION RESTON, VIRGINIA 
‘R’C’NATCR TELECOMMUNICATIONS MANAGER 
‘ASKS PHONE. ” (703) 555-1212 
‘WORK ORDER ff 2.2 (TASK #4) 
e Assign and remove feature assignments for EKT button with CMC-203. 
‘ARAMETERS 
(1) Assign “Call Park” to button 1 for both 
CS-20 instruments. INSTRUCTIONS 
(1) Perform programming changes for station 
instruments. 
(2) Change the “Forward All” feature assigned by 
(2) 
default to a button on station 308, to the “Do Check/test the operation of changes after 
Not Disturb” feature. completion of this portion of the laboratory 
activity. 
(3) Change the “Call Announce” feature also 
(3) Complete review exercise questions l-l 7. 
assigned by default to a button on station 308, 
to the “System Speed Calling” feature (code 00). 
NOTE: 
Programming of EKT buttons for trunk 
termination or key system type features will be 
addressed in later laboratory activities. 
LF/DSS Modules 
LAB MILESTONE 
. VERIFY THAT ALL PROGRAMMING CHANGES REQUESTED IN WORK ORDERS HAVE 
BEEN PERFORMED CORRECTLY. 
l ASK INSTRUCTOR TO INSPECT STATION PROGRAMMING CHANGES AND INITIAL 
YOUR PERFORMANCE CHECKLIST. 
l MAKE CERTAIN QUESTIONS 1-17 OF REVIEW EXERCISE 2.2 HAVE BEEN COMPLETED 
BEFORE COMPLETING THE REMAINING WORK ORDERS. 
2.56  
						

							ry Activity - 
Instrument 
Modules (Continued) 
WORK ORDER #2.2 
ZOMPANY NAME: NU SYSTEM CO. PHONE #: (703) 5551212 
-0CATlON: RESTON, VIRGINIA WORK ORDER #2.2 
(TASK #5) 
IRlGlNATOR: TELECOMMUNICATIONS MANAGER 
TASKS: 
e Add, change, or delete a BLF/DSS module with CMC-210. 
‘ARAMETERS: INSTRUCTIONS: 
(1) Install and add a 40 button BLF/DSS to card (1) Perform programming changes for BLF/DSS 
01, circuit 3. (NOTE: Cross connect wiring was 
modules. 
completed during installation. Simply connect 
BLF/DSS to modular jack, perform HOT (2) Check/test the operation of changes after 
Restart, and proceed with required completion of this portion of the laboratory 
programming.) activity. 
(2) Assign the BLF/DSS as BLF/DSS module (3) Proceed to next work order task. 
Number 2. Pair it with the CS-20 instrument at 
station directory 214. 
2.57