GTE Omni Scbs Installation And Maintenance Manual

							Review Exercise (1.1) - Installation 
INSTRUCTIONS: 
THE FOLLOWING EXERCISE CONSISTS OF MULTIPLE CHOICE, FILL IN THE BLANK OR MATCHING 
TYPE QUESTIONS. ALL AVAILABLE RESOURCES (I.E. STUDENT WORKBOOK, NOTES, AND GTEP 
MANUAL) MAY BE USED AS REFERENCES. SUBMIT EXERCISE TO INSTRUCTOR FOR GRADING 
WHEN LAST QUESTION HAS BEEN COMPLETED. 
1. 
2. 
3. 
4. 
5. 
6. (TRUE OR FALSE) 
THE OMNI SBCS SYSTEM REQUIRES ADDITIONAL COOLING. 
(TRUE OR FALSE) 
THE OMNI SBCS POWER SUPPLY WILL ACCEPT EITHER 110 VAC, 220 VAC, OR 
48 VDC AS ITS INPUT POWER SOURCE. 
Tl-iE SYSTEM BACKUP BATTERY WILL MAINTAIN THE SYSTEM MEMORY FOR A PERIOD OF 
APPROXIMATELY: 
A. 2 DAYS B. 5 DAYS C. 1 WEEK 
D. 2 WEEKS 
(TRUE OR FALSE) 
THE DEFAULT STANDARD DATA BASE MUST BE LOADED FROM TAPE OR FLOPPY 
DISKETTE AT TIME OF SYSTEM INSTALLATION. 
THE COMMON CONTROL CARDS REQUIRED FOR A MINIMUM SYSTEM CONFIGURATION CONSIST OF: 
A. 
CPM, SWC, AND RGEN CARDS 
B. CMC, MEM, AND RGEN CARDS 
C. CPM, 4DMR, AND 6PFT CARDS 
D. CPM, SWC, AND MEM CARDS 
THE MAXIMUM NUMBER OF STATIONS SUPPORTED BY THE SYSTEM IS 
AND 
THE MAXIMUM 
NUMBER OF TRUNKS SUPPORTED BY THE SYSTEM IS 
, ALTHOUGH THESE CAPACITIES 
CANNOT 
BE ACHIEVED SIMULTANEOUSLY. 
1.34  
						

							7. (TRUE OR FALSE) GTE’ OMNL’SBGS CARD SLOTS 06 THROUGH 18 CAN CONTAIN LINE OR TRUNK CARDS. 
8. (TRUE OR FALSE) 
CARD SLOTS 19,20, AND 21 ARE RESERVED FOR COMMON CONTROL CARDS. 
9. THE TWO RS-232-C PORTS AVAILABLE ON THE SYSTEM CABINET FOR THE PORTABLE MAINTENANCE PANEL OR THE 
SMDR PRINTER ARE 
OR 
MATCH THE FOLLOWING CARDS WITH THE CORRECT DESCRIPTION: 
10. 
11. 
12. 
13. 
14. 
15. 
16. 
17. 
18. 
19. 
20. 
21. CPM CARD 
MEM CARD 
SWC CARD 
RGEN CARD 
8EKC CARD 
8SLC CARD 
4BWC CARD 
2TTE CARD 
2TTL CARD 
4DMR CARD 
6PFT CARD 
8DTC CARD A. 
B. 
C. 
D. 
E. 
F. 
G. 
H. 
I. 
J. 
K. 
L. 2 CIRCUIT E&M TIE LINE TRUNK CARD SUPPORTING TYPE I AND TYPE II 
SIGNALING 
8 CIRCUIT LINE CARD SUPPORTING ELECTRONIC KEY TELEPHONES 
CONTANS PCM TIME DIVISION MULTIPLEXOR/DEMULTlPLEXOR CIRCUITS 
INTERFACES WITH 8SLC AND 4BWC CARD TO PROVIDE SIX POWER FAIL 
TRANSFER STATIONS 
8 CIRCUIT DIGITAL INTERFACE CARD SUPPORTING CSD TELEPHONES AND 
DATA INTERFACE UNITS 
4 CIRCUIT CO TRUNK CARD WHICH CAN ALSO PROVIDE MUSIC-ON-HOLD, 
EXTERNAL PAGING, AND POWER FAILURE TRANSFER INTERFACES 
8 CIRCUIT LINE CARD SUPPORTING DTMF AND ROTARY DIAL SINGLE LINE 
TELEPHONES 
2 CIRCUIT LOOP START TIE LINE TRUNK CARD 
CONTAINS ADDITIONAL MEMORY AS EXTENSION OF CPM CARD WITH ROM 
FOR OPERATING SYSTEM SOFTWARE AND RAM FOR CUSTOMIZED DATA BASE 
4 CIRCUIT CARD PROVIDING TONES IF TELEPHONES REQUIRING DUAL TONE 
MULTI-FREQUENCY ARE INSTALLED 
GENERATES RINGING TONES FOR SINGLE LINE TELEPHONES OR POWER TO 
MESSAGE WAITING FEATURE ON SINGLE LINE TELEPHONES WITH MESSAGE 
WAITING LAMP 
CONTAINS 16 BIT MICROPROCESSOR FOR SYSTEM OPERATION, REAL TIME 
CLOCK, AND ROM FOR OPERATING SYSTEM SOFTWARE AND RAM FOR 
CUSTOMIZED DATA BASE 
1.35  
						

							MATCH THE FOLLOWING COMPONENTS WITH THE CORRECT DESCRIPTION: 
22. cs-10 
23. cs-20 
24. CSD 
25. BLF/DSS A. 
B. 
C. 
D. 
26. PMP 
E. 
27. SMDR 
28. MUSIC-ON-HOLD 
29. SLT 
30. FLOPPY DISKETTE 
DRIVE F. 
G. 
H. 
I. DTMF OR DIAL PULSE (ROTARY) TELEPHONE INSTRUMENT 
ELECTRONIC KEY TELEPHONE WITH 10 PROGRAMMABLE BUTTONS AND 
MONITOR CAPABILITIES 
MICROCOMPUTER USED FOR SYSTEM DATA BASE ADMINISTRATION AND 
MAINTENANCE 
OPTIONAL UNIT USED TO DECREASE TIME ASSOCIATED WITH SAVING OR 
LOADING THE CUSTOMIZED DATA BASE 
PROVIDES MUSIC TO CALLING PARTIES BY MUSIC SOURCE INTERFACED 
THROUGH A 4BWC CARD 
ELECTRONIC KEY TELEPHONE WITH 10 PROGRAMMABLE BUTTONS, 
SPEAKERPHONE, AND 20 CHARACTER LCD DISPLAY 
40 OR 80 BUTTON EXPANSION MODULE USED TO PROVIDE VISUAL INDICATORS 
FOR STATUS OF LINES IN SYSTEM 
PRINTER USED TO PROVIDE HARD COPY RECORDS OF SYSTEM CALLS 
DIGITAL TELEPHONE WHICH CAN PROVIDE INTERFACE TO DATA TERMINAL IF 
EQUIPPED WITH DATA TERMINAL ADAPTER (DTA) 
31. (TRUE OR FALSE) 
ONLY SIX ELECTRONIC KEY TELEPHONES MAY BE DESIGNATED AS POWER FAIL 
TRANSFER STATIONS. 
1.36  
						

							1.37  
						

							TEM INSTAL ATION 
Cabinet Installation 
1.38  
						

							1.2 Enabling Objective/ 
binet Inst 
GIVEN: 0 
GTE OlVlNl SBCS WITH MOUNTING BRACKET, CABINET, AND POWER SUPPLY 
0 
GTE OMNI SBCS PCB CARDS 
0 
#6 AWG CABLE, POWER SUPPLY CABLE, AND HARDWARE 
0 
GTE OMNI SBCS COURSE AND SITE DOCUMENTATION PACKAGE 
0 
STANDARD INSTALLATION TOOLS 
0 
REVIEW EXERCISE 
ACTION: 0 
0 
0 
0 
0 
CRITERIA: 0 
0 MOUNT AND INSTALL SYSTEM CABINET AND POWER SUPPLY. 
CONNECT POWER SUPPLY CABLE. 
GROUND WIRE TERMINALS TO COLD WATER GROUND AND CONNECT SIGNAL 
WIRE GROUND. 
INSERT AND SEAT COMMON CONTROL, LINE, TRUNK, AND RING GENERATOR 
CARDS IN CORRECT CARD SLOTS. 
COMPLETE REVIEW EXERCISE. 
CABINET AND POWER SUPPLY WILL BE INSTALLED AND GROUNDED IN 
ACCORDANCE WITH GTE OMNI SBCS GTEP MANUAL. CARDS WILL BE 
INSERTED AND SEATED CORRECTLY IN DESIGNATED CARD SLOTS. 
REVIEW EXERCISE QUESTIONS WILL BE COMPLETED CORRECTLY IN 
ACCORDANCE WITH PASS/FAIL CRITERIA OF THIS TRAINING ORGANBZ 
1.39  
						

							ask Installation Se 
(1) 
(2) 
(3) 
(4) 
(5) 
(6) 
(7) 
(8) 
(9) 
(10) 
(11) 
(12) INSTALL MOUNTING BRACKET. 
MOUNT AND INSTALL CABINET AND POWER SUPPLY. (NOTE: DO NOT POWER 
ON SYSTEM UNTIL CARDS AND PERIPHERALS HAVE BEEN INSTALLED). 
GROUND POWER SUPPLY AND CABINET. 
INSTALL COMMON CONTROL CARDS, LINE CARDS, AND TRUNK CARDS. 
INSTALL CABLES FROM CABINET AND RECEPTACLES TO CDF CROSS 
CONNECTION BLOCKS. 
WIRE ALL STATION AND TRUNK CROSS CONNECTIONS. 
INSTALL PERIPHERAL INSTRUMENTS (E.G., STATION INSTRUMENTS, BLF/DSS 
CONSOLES, SMDR, PMP, ETC.). 
POWER SYSTEM ON. 
COLD RESTART SYSTEM TO ESTABLISH DEFAULT STANDARD DATA BASE. 
VERIFY SYSTEM/FEATURE OPERATION. 
DRESS AND TIE CABLES AS REQUIRED. CLEAR INSTALLATION SITE. 
MODIFY DEFAULT STANDARD DATA BASE TO MEET CUSTOMER’S 
REQUIREMENTS. 
1.40  
						

							(1) 
(2) 
(3) 
 lh MOUNTING 
““7\‘1 MOUNTING 
EQu’PMENTeE “I& 
CABINET 
MOUNT EQUIPMENT CA5lNET TO THE MOUNTING BRACKET BY 
LOWERING THE CABINET ONTO THE BRACKETS. 
AFTER CABINET IS SECURELY MOUNTED, THEN INSTALL THE 
POWER SUPPLY. 
SECURE BOTH CABINET AND POWER SUPPLY WITH THE SCREWS 
PROVIDED. 
1.42  
						

							Cabinet - Power Supply Cable 
TO POWER 
SUPPLY 
UNIT TO 
EQUIPMENT 
CABINET 
SAFETY 
KEY 
SAFETY 
KEY 
BOWER 
SUPPLV 
RECEPTACLE 
FRONT VIEW OF CONNECTORS 
LOCATION OF RECEPTACLES 
CABLE FOR 
CABINET-POWER SUPPLY CONNECTION 
NOTE: CONNECT POWER SUPPLY CABLE TO EQUIPIVIEMT CABINET 
ONLY WHEN SY IMSTALLATBO PROCEDURE HAS BEEN 
COMPLETED. 
1.43