GTE Omni Scbs Installation And Maintenance Manual

							Data Interface Unit
(DIU) Programming
DESCRIPTION
.PROVIDES STANDALONE DATA STATION CAPABILITY WITH TERMINAL, MODEM, OR PRINTER
. PROGRAMMABLE DIU FEATURES INCLUDE:- COS/COR
- DATA ATTRIBUTES
- TENANT GROUP
- DATA HUNT GROUP
- DATA HOT LINE
piiGEq
1.ASSIGN THE DIU AS A DATA STATION WITH CMC-220:
.EQUIPMENT NUMBER OF DATA STATION (PI)
.DIRECTORY NUMBER OF DATA STATION (P2)
@DATA TERMINAL TYPE (P3) - (4 = DIU)
.DIRECTORY NUMBER OF VOICE STATION (P4) 
- BLANK
2.ASSIGN COS/COR TO DIU DATA STATION WITH CMC-221:
.DIRECTORY NUMBER OF DATA STATION 
(Pl).CLASS OF SERVICE DAY (P2)
.CLASS OF SERVICE NIGHT (P3)
.CLASS OF RESTRICTION DAY (P4)
.CLASS OF RESTRICTION NIGHT (P5)
5.86
CMC = 220
Pl: 030 P4:
P2: 4700 
P5:
P3: 4
CMC = 221
Pl: 4700P4:1
P2: 1P5:1
P3: 1 
						

							Qata Interface Unit (DIU)
Programmin(ContinPROCEDURE (Continued) .
3.ASSIGN DATA ATTRIBUTES OF DIU WITH CMC-222:
@DIRECTORY NUMBER OF DATA STATION (PI). DATA SPEED (P2)
0 SYNCHRONIZATION AND COMMUNICATION (P3)
. WORD STRUCTURE (P4)
l ,PARITY (P5)
8 ECHOPLEX (P6)
4. ASSIGN DATA ATTRIBUTES AND RS-232-C INTERFACE FOR DIU WITH
CMC-223:.
DIRECTORY NUMBER OF DATA DIU (Pl).
CALL CONTROL MODE (P2).
RS-232-C INTERFACE SIGNAL MODE 1 (P3)
0RS-232-C INTERFACE SIGNAL MODE 2 (P4)
5.ASSIGN DATA ATTRIBUTES, TENANT GROUP, AND METERING GROUP TO
DIU WITH CMC-224:.
DIRECTORY NUMBER OF DATA DIU (Pl)
e CALL OPERATION MODE (P2)
@DIAL MODE (P3) - (BLANK)
@ TENANT NUMBER (P4)
@ METERING GROUP (P5)CMC = 222
Pl: 4700P4: 1
P2: 5P5: 3
P3: 3CMC = 223
Pl: 4700P4: 1
P2: 010
P3:CMC = 224
Pl: 4700 P4:
P2: 1P5:
P3: 0
5.87 
						

							PROCEDURE (Continued)6.ASSIGN DIU DATA STATION TO HUNT GROUP WITH CMC-301:
ICMC = 301
Pl: 51P4: 1.STATION HUNTING GROUP NUMBER 
(Pl) - (51 - 60)P2: 1
l TERMINATING ORDER (P2)P3: 4700
.
DIRECTORY NUMBER OF DATA STATION (P3). HUNTING TYPE (P4)
1
7.ASSIGN DIU DATA STATIONS TO HOT LINE SERVICE WITH CMC-304:
eHOT LINE NUMBER (Pl) - (51 - 90)
.
ORIGINATING DATA STATION (DIRECTORY NUMBER) - (P2).
TERMINATING DATA STATION DN (DIRECTORY NUMBER) - (P3)
IData Interface Unit 
(DILJ)Programming (Continued)
5.88 
						

							Data Interface Unit (DIU) Programming -
CMC Command Summary
CATEGORY. DATA STATION ASSIGNMENT
. DATA STATION 
COS/COR
ASSIGNMENT
e DATA STATION ATTRIBUTES
ASSIGNMENT (I)
@ DATA STATION’S ATTRIBUTES
ASSIGNMEMTS (II) AND RS-232-C
SIGNAL MODES
@ DATA STATION ATTRIBUTES
ASSIGNMENT (Ill)
@ DATA STATION HUNT GROUP
ASSIGNMENT
8 DATA STATION HOT LINE
ASSIGNMENTCMC TABLE
CMC-220
\
CMC-221
CMC-222
CMC-223
CMC-224
CMC-301
CMC-304
5.89
FUNCTION
INSTALLS OR REMOVES DIU AS DATA
STATION WITH ITS ASSOCIATED
DIRECTORY NUMBERSCHANGES DATA STATION‘S COS/COR
ASSIGNMENTASSIGNS DATA STATION‘S ATTRIBUTES
INCLUDING DATA SPEED, SYNCHRONI-ZATION AND 
COMMUNCATIONS WORD
STRUCTURE, PARITY, AND ECHOPLEXASSIGNS DATA STATION’S ATTRIBUTES
INCLUDING CALL CONTROL MODE AND
RS-232-C INTERFACE SIGNAL MODES
ASSIGNS DATA STATIONS’S ATTRIBUTES
INCLUDING 
OEPRATION MODE, DIAL
MODE, TENANT NUMBER, AND METERING
GROUPASSIGNS DATA STATION HUNT GROUPS
AND MEMBERSASSIGNS DATA STATION HOT LINE
SERVICE 
						

							Programming Data Interface Unit (DIU)
Associated with CS-lO/CS-20.ALLOWS 
DIU ASSOCIATED WITH CS-10 OR CS-20 TO ESTABLlSH DATA CALLS AND PROVIDE SAME
OPERATION AS CSD WITH DATA TERMINAL ADAPTER (DTA).
1.ASSIGN CS-10 OR CS-20 AS VOICE STATION ASSOCIATED
WITH DIU WITH CMC-220:
@EQUIPMENT NUMBER OF DATA STATION (Pl).
DIRECTORY NUMBER OF DATA STATION (P2).
DATA TERMINAL TYPE (P3) - (2 = DIU AND CS-lO/CS-20)
0DIRECTORY NUMBER OF VOICE STATION (P4)
2.ASSIGN DATA CALL BUTTON TO CS-20 OR CS-20
ASSOCIATED WITH DIU WITH CMC-203:. STATION DIRECTORY NUMBER 
(Pl). BUTTON NUMBER (P2)
.
.
FEATURE NUMBER (P3) - (185 = DATA CALL FEATURE NUMBER)
SUPPLEMENTARY DATA (P4) 
- (BLANK).
LINE TERMINATING TYPE (P5) - (BLANK).
RINGING MODE (P6) - (BLANK)
5.90CMC = 220
PI: 031
P4: 212
P2: 4702
P3: 2CMC = 203
Pl: 212 P4:
P2: 4P5:P3: 185 P8: 
						

							Programming Data Inrface Unit (DIU)
Associated with 
CSl
CATEGORY. DATA STATION ASSIGNMENT
@ EKT BUTTON ASSIGNMENT
CMC TABLE
CMC-220
CMC-203
5.91
FUNCTION
INSTALLS OR REMOVES DIU WITH
CS-20/C&20 AS VOICE/DATA STATION
WITH ITS ASSOCIATED DIRECTORY
NUMBERS
ASSIGNS DATA CALL BUTTON TO CS-10 OR
CS-20 TELEPHONE ASSOCIATED WITH DIU 
						

							Programming Key
FeKEY TELEPHONE EKT BUTTON ARRANGEMENT
FORWARDSAVE/FORWARDSAVE/LINE 1CAMP ONALLREPEATICMLINE 1CAMP ONALLREPEATICM
DDD[IDnDDDDDO NOT
CALL
CALLSPEAKER-DISTURBANNOUNCESPEAKERTRANSFERHOLDANNOUNCEMUTEPHONETRANSFERHOLD
DDDDDDDanD
CS-10 BUTTON ASSIGNMENTS FOR TELEPHONES
CS-20 BUTTON ASSIGNMENTS FOR TELEPHONES
CONNECTED TO CARD SLOTS OTHER THAN 01CONNECTED TO CARD SLOTS OTHER THAN 01TRUNK
FORWARDSAVE/LINE 1(IN)ALLREPEAT
ICM
DDDDDDO NOT
CALL
DISTURBANNOUNCE
SPEAKERTRANSFERHOLD
DDIIDDTRUNK
FORWARDSAVE/LINE 1(IN)ALLREPEATICM
II-DDDIICALLSPEAKER-
ANNOUNCEMUTEPHONETRANSFER
HOLD
IDDID
CS-10 BUTTON ASSIGNMENTS FOR TELEPHONESCS-20 BUTTON ASSIGNMENTS FOR TELEPHONES
CONNECTED TO CARD SLOT 01
CONNECTED TO CARD SLOT 01
NOTE: TELEPHONES CONNECTED TO CARD SLOT 
01 WILL RING ON ALL INCOMING CALLS (ANSWERING
STATION).5.93 
						

							Laboratory Activity - Package
tasePART 1: ATTENDANT CONSOLEn (5.3)
1.TEST THE FOLLOWING ATTENDANT CONSOLE FEATURE BUTTONS (USING ATTENDANT CONSOLE USER’S GUIDE FOR
REFERENCE):
A. 
COS/CORB. TRUNK CAMP-ON
C. EKT STATION PAGING
D. MESSAGE LEAVING
E. ACCOUNT CODE ENTRY
2.USE CMC-231 TO PERFORM THE FOLLOWING TASKS:
A.IDENTIFY THE DEFAULT FEATURE ASSIGNED TO BUTTON 14 OF THE ATTENDANT CONSOLE.
B.REMOVE THE FEATURE FROM IBUTTON 14 AND ASSIGN THE FDC PROGRAM FEATURE (WHICH WILL BE USED FOR
HOTEL/MOTEL TASKS LATER IN THIS LABORATORY ACTIVITY).
3.USE CMC-233 TO ASSIGN ATTENDANT CONSOLE PRlORlTlES FOR INCOMING CALL TERMINATION. ASSIGN LOW
PRIORITY TO THE LOOP TIE TRUNK LINES AND HIGH PRIORITY TO THE 
E&M TIE TRUNK LINES. TEST THESE INCOMING
CALL TERMINATION ASSIGNMENTS BY CALLING FROM TWO OF THE OTHER SYSTEMS, TO CONFIRM THAT
ATTENDANT CONSOLE SELECTS PRIORITY BASED ON TRUNK GROUP.
4.USE CMC-306 TO COMPLETE THE FOLLOWING STEPS ASSOCIATED WITH CREATING AN ATTENDANT CONSOLE
OVERFLOW STATION.
A.CREATE A NIGHT ANSWER GROUP FOR THE ATTENDANT CONSOLE OVERFLOW STATION (PI = 1).
B.IDENTIFY NIGHT ANSWER GROUP AS A STATION (P2 = 1)
C.IDENTIFY THE EQUIPMENT NUMBER OF THE CS-20 STATION DESIGNATED TO SERVE AS THE ATTENDANT
CONSOLE OVERFLOW STATION (P3 = 
016), THEN ENTER THE ABOVE PARAMETER VALUES WITH THE
ADD/CHANGE FUNCTION KEY.
D.CONTINUE TO USE CMC-306 TO ASSIGN ALL TENANTS TO THE NIGHT ANSWER GROUP JUST CREATED BY
DESIGNATING THE FOLLOWING VALUES: Pi = 1, P2 = 3 (INDICATING TENANT), AND P3 = * (INDICATING ALL
TENANTS). ENTER THESE PARAMETER VALUES WITH THE ADD/CHANGE FUNCTION KEY.
E.TEST THE OVERFLOW ASSIGNMENT BY ACTIVATING THE ATTENDANT CONSOLE’S ‘POSITION BUSY’ FEATURE
BUTTON.PLACE AN INCOMING CALL TO THE SYSTEM TO DEMONSTRATE THAT THE OVERFLOW STATION NOW
RECEIVED THE CALLS INTENDED FOR THE ATTENDANT CONSOLE.
5.94 
						

							Laboratory Activity - Package C Data Base
Adminstation (5.3) (Continued)
PART 2: HOTEL/MOTEL
1.USE CMC-203 TO ASSIGN THE CSD TELEPHONE (EQUIPMENT NUMBER 000) AS THE FRONT DESK CONSOLE.d
2.USE CMC-204 TO SET FLAG WHICH WILL ASSIGN ALL LABORATORY ‘STATIONS (EXCEPT PREVIOUSLY DESIGNATED
CSDIFDC) AS GUEST ROOMS.
3.USE CMC-354 TO ASSIGN THE BLF/DSS MODULE (EQUIPMENT NUMBER 015) AS A ROOM STATUS INDICATOR MODULE.
4.USE CMC-355TO ASSIGN HOTEL/MOTEL ROOMS (STATION DIRECTORY NUMBERS) TO BUTTONS ON THE ROOM STATUS
INDICATOR MODULE.
5.USE CMC-356 TO ASSOCIATE THE HOTEL/MOTEL PRINTER WITH A 4CHT CIRCUIT (EQUIPMENT NUMBER 090) AND A DIU
DIRECTORY NUMBER (202).
6.ASSIGN THE HOTEL/MOTEL PRINTOUT MESSAGE ALLOCATION WITH CMC-357, USING THE FOLLOWING PARAMETER
VALUES:INDEPENDENT MESSAGES 
-
Pl = 1P2 = 1 (INDICATING INDEPENDENT MESSAGES)
P3 = 01 (TAKING MESSAGES FROM THE ATTENDANT CONSOLE)
COMMON MESSAGES 
-
PI = 1P2 = 2 (INDICATING COMMON MESSAGES)
P3 = BLANK
7.USE CMC-350 TO ASSIGN THE MESSAGE REGISTRATION TRUNK GROUP NUMBER. MAKE ALL CO TRUNKS (TGN 13)
SUBJECT TO HOTEL/MOTEL MESSAGE REGISTRATION.
8.USE CMC-351 TO ASSIGN MESSAGE REGISTRATION BILLING RATE NUMBER 1 TO THE FOLLOWING OFFICE CODES: 227,
476, AND 892.
5.95 
						

							Laboratory Acti- PackageC
instrantinued)
9.USE CMC-352 TO ASSIGN THE FOLLOWING BILLING RATES FOR BILLING RATE NUMBER 1:
INITIAL TIME FOR TELEPHONE CALL (P2) = 20 SECONDS
INITIAL CHARGE FOR TELEPHONE CALL (P3) = 50 CENTS
ADDITIONAL TIME FOR TELEPHONE CALL (P4) = 60 SECONDS
ADDITIONAL CHARGE FOR TELEPHONE CALL (P5) = 30 CENTS
10.USE CMC-100 TO CREATE NEW ACCESS CODES FOR THE FOLLOWING HOTEL/MOTEL CODES:
FNO 73 
-GUEST ROOM CLEAN-UP
FNO 78 
-WAKE-UP REGISTRATION
FNO 79- WAKE-UP CANCELLATION
FNO 96 
- SERVICE CALL ROUTING #IFNO 97 
- SERVICE CALL ROUTING #2
FNO 98- SERVICE CALL ROUTING #3ENSURE THAT NEW CODES DO NOT CONFLICT WITH EXISTING SYSTEM ACCESS CODES.
11.USE CMC-353 TO ASSIGN SERVICE CODE DESTINATIONS TO THE SERVICE CALL FEATURE ACCESS CODES (PREVIOUSLYASSIGNED). ASSIGN THE FOLLOWING PARAMETER VALUES:
Pl = (USE ACCESS CODES ASSIGNED TO FNO 96,97, AND 98)
P2 = 
1 (INDICATING SPECIAL SERVICE)
P3 = 200 (DESTINATION DIRECTORY NUMBER)
P4 = BLANK
5.96