GTE Omni Scbs Installation And Maintenance Manual

							Programming Station Message 
etail Recorder/SMDR 
a?wt F 
@ TIME MESSAGE IS PRINTED WITH SMDR REPORT TO SEPARATE EACH SMDR MESSAGE. TIME INCRE- 
MENTS BY HOUR. 
09:27 02107186 
(1) (2) 
Time Date 
. SAMPLE OUTPUT: 
08:15 00.00.36 ST 0201 Cl234 1600 07035344789 123456780123 00 00 
(1) 
(2) (3) (4) (5) (6) (7) (8) (0% (10) 
(I) = Time of call origination 
(2) = Duration of call 
(3) = Calling party identification: 
ST = Station 
AT = Attendant 
TI = TIE trunk 
(4) = Originating Station number 
(5) = Trunk Identification and Trunk number: 
c: CO trunk DDD: Trunk number 
F: FX trunk 
w: WATS trunk 
T: TIE trunk 
0.5) = Trunk access code (also when line button on EKT is used, access code is output) 
(7) = Directory number dialed (maximum 20 digits) 
(8) = Account code (if not specified, no code is output) 
(9) = Tenant number (if not specified, no tenant number is output) 
(IO) = Metering group (if not specified, no metering group is output) 
2.156  
						

							Programming Station Message 
Detail Recorder/CMC 
Command Summary 
CATEGORY 
l OUTGOING MDR 
l MDR TRUNK SCREEN 
. CLASS OF RESTRICTION 
. TENANT 
. CALL DURATION 
CMC TABLE 
FUNCTION 
CMC-500 SELECTS CO, TIE, ACCOUNT AND TOLL 
FOR SMDR OUTPUT 
CMC-501 SELECTS TRUNK GROUPS FOR MDR 
OUTPUT 
CMC-502 
SELECTS COR GROUPS FOR MDR OUTPUT 
CMC-503 SELECTS TENANTS FOR SMDR OUTPUT 
CMC-504 
SETS MINIMUM CALL DURATION FOR MDR 
REGISTRATION 
NOTE: REFER TO MODULE Ill FOR SMDR MAINTENANCE COMMANDS 
(CMC-705) AND CMC-901). 
2.157  
						

							- 
,, 
Laboratory Activity - Station Message 
etail 
Recsr rogramming 
GTE OMNU SBCS 
PERFORM THE FOLLOWING PROGRAMMING TASKS IN THE SEQUENCE 
OUTLlNED BELOW USING THE SAMPLE WORK ORDERS AND IN ACCOR- 
DANCE WITH THE GTE OMNI SBCS GTEP MANUAL. COMPLETE THE REVIEW 
EXERCISE QUESTIONS PERTAINING TO STATION MESSAGE DETAIL RE- 
CORDER PROGRAMMING UPON COMPLETION OF THIS LABORATORY 
ACTIVITY. 
WORK ORDER #2.8 
ZOMPANY NAME: NU SYSTEM CO. PHONE #: (703) 5551212 
-0CATION: RESTON, VIRGINIA WORK ORDER 
#2.8 (TASK #l) 
IRIGINATOR: TELECOMMUNICATIONS MANAGER 
TASKS: 
l Determine SMDR output for system parameters with CMC-500. 
(1) Assign both tie line outgoing connections with (1) Perform programming changes for Station 
“no SMDR output”. Message Detail Recorder. 
(2) Change toll call flag to indicate “SMDR output (2) Check/test the operation of changes after 
for toll calls only”. completion of this portion of the laboratory 
2.158  
						

							Laboratory Activity - Station 
Message Detail Recorder 
Programming (Continued) 
WORK ORDER #2.8 
COMPANY NAME: NU SYSTEM CO. 
LOCATION: RESTON, VIRGINIA 
ORIGINATOR: TELECOMMUNICTIONS MANAGER 
TASKS: PHONE #: (703) 5551212 
WORK ORDER #2.8 (TASK #2) 
l Establish minimum call duration for SMDR with CMC-504. 
PARAMETERS: 
INSTRUCTIONS: 
(1) Specify 45 seconds for “minimum call duration” (1) Perform programming changes for Station 
to receive SMDR output. Message Detail Recorder. 
(2) Check/test the operation of changes after 
completion of this portion of the laboratory 
activity. 
(3) Proceed to next work order task: 
2.159  
						

							oratory wity - Station Message 
tail .Reco mming (Continued) 
WORK ORDER #2.8 
:OMPANY NAME: NU SYSTEM CO. PHONE #: (703) 555-1212 
.OCATION: RESTON, VIRGINIA WORK ORDER #2.8 (TASK #3) 
)RfCfNATCR. TELECOMMUNICATIONS MANAGER 
-ASKS: 
e Assign SMDR output for COR with CMC-502. 
‘ARAMETERS. 
(1) Change COR 3 and 4 to indicate “no SMDR 
OUTPUT”. INSTRUCTIONS: 
(1) Perform programming changes for Station 
Message Detail Recorder. 
(2) Check/test the operation of changes after 
completion of this portion of the laboratory 
activity. 
(3) complete review exercise questions l-8. 
NOTE: 
Tenant Group SMDR output was assigned 
previously during Special System 
Configuration laboratory activity with 
CMC-503. 
LAB MILESTONE: 
. VERIFY THAT ALL PROGRAMMING CHANGES REQUESTED IN WORK ORDERS HAVE 
BEEN PERFORMED CORRECTLY. 
e ASK INSTRUCTOR TO INSPECT STATION MESSAGE DETAIL RECORDER AND INITIAL 
YOUR PERFORMANCE CHECKLIST. 
e MAKE CERTAIN QUESTIONS l-8 OF REVIEW EXERCISE 2.8 HAVE BEEN COMPLETED 
BEFORE SUBMITTING TO THE INSTRUCTOR FOR GRADING. 
2.160  
						

							Student Notes 
P 
2.161  
						

							Review Exercise - Station Message Detail 
Recorder (2.8) 
GTE OMNU SBCS 
INSTRUCTIONS: THE FOLLOWING EXERCISE CONSISTS OF MULTIPLE CHOICE, TRUE/FALSE, FILL 
IN THE BLANK, OR MATCHING TYPE QUESTIONS. ALL AVAILABLE RESOURCES (I.E. STUDENT 
WORKBOOK, NOTES, AND GTEP MANUAL) MAY BE USED AS REFERENCES. SUBMIT EXERCISE TO 
INSTRUCTOR FOR GRADING WHEN LAST QUESTION HAS BEEN COMPLETED. 
1. 
2. 
3. 
4. 
5. THE FOLLOWING INFORMATION IS RECORDED FOR EVERY CALL IF SMDR OUTPUT IS 
SELECTED: ~ 
A. TIME OF CALL ORIGINATION, CALL DURATION, AND CLASS OF RESTRICTION SELECTION. 
B. CALL DURATION, CALLING PARTY IDENTIFICATION, AND TOLL CALLS. 
C. CALL DURATION, ORIGINATING STATION NUMBER, AND TRUNK ACCESS CODE. 
D. TIME OF CALL ORIGINATION, OVERTIME CALLS, AND METERING GROUP NUMBER. 
WHAT CMC COMMAND, PARAMETERS AND SETTINGS WOULD BE REQUIRED TO ESTABLISH 
SMDR OUTPUT FOR OUTGOING CO CONNECTIONS, AND TOLL AND NON-TOLL CALLS? 
SMDR OUTPUT FOR TRUNKS IS IDENTIFIED ON PRINTOUT BY 
WHY MIGHT A MINIMUM CALL DURATION TO RECEIVE SMDR OUTPUT BE SELECTED? 
WHAT CMC COMMAND, PARAMETERS, AND SETTINGS WOULD BE REQUIRED TO ESTABLISH 
A MINIMUM CALL DURATION OF 1% MINUTES? 
2.162  
						

							Review Exercise 
- Station Message 
Detail Recorder 
(2.8) 
GUE c&MN/ SBCS 
6. WHAT CMC COMMAND, PARAMETERS, AND SETTlNG WOULD BE REQUIRED TO PROVIDE SMDR 
OUTPUT FOR COR LEVELS 6 AND 16? 
7. IS IT NECESSARY FOR ALL FIVE TENANTS TO RECEIVE SMDR OUTPUT? 
PLEASE EXPLAIN 
8. MATCH EACH OF THE FOLLOWING CMC COMMANDS WITH ITS CORRECT DEFINITION: 
CMC-500 
A. SMDR COR SCREENING ASSIGNMENT 
CMC-501 
B. SMDR CALL DURATION SCREENING ASSIGNMENT 
CMC-502 
C. SMDR OUTGOING CONNECTION SCREENING ASSIGNMENT 
CMC-503 D. SMDR TENANT SCREENING ASSIGNMENT 
CMC-504 
E. SMDR TRUNK GROUP SCREENING ASSIGNMENT 
CMC-705 
F. SMDR IN/OUT OF SERVICE 
2.163  
						

							DATA BASE ADMINISTRATION 
Programming Toll and 
Multi-Digit Restriction 
2.164  
						

							abling Objective 
GIVEN: 
@ GTE OMNI SBCS 
. GTE OMNI SBCS PERIPHERALS 
@ PORTABLE MAINTENANCE PANEL 
@ GTE OMNI SBCS COURSE AND SITE DOCUMENTATION PACKAGE 
0 LABORATORY ACTIVITY 
- PROGRAMMING TOLL AND MULTI-DIGIT 
RESTRICTION PROGRAMMING 
@ REVIEW EXERCISE 
ACTION: 
. USE OMNI SBCS PROGRAMMING TOOLS AND EQUIPMENT TO: 
- ASSIGN TOLL AND TRUNK GROUP RESTRICTIONS TO CLASS 
OF RESTRICTION TABLE. 
- CREATE AREA CODE, OFFICE CODE, AND COMBINED AREA/ 
OFFICE CODE MULTI-DIGIT RESTRICTION TABLES. 
- ESTABLISH TOLL AND OPERATOR CALL RESTRICTION NUMBER. 
- IDENTIFY AND ASSIGN TOLL AND OPERATOR PREFIX CODES 
FOR TRUNK DIAL GROUP NUMBERS. 
. COMPLETE REVIEW EXERCISE. 
CRITERIA: 
0 DEMONSTRATION OF ABOVE TASKS IN ACCORDANCE WITH 
PROCEDURES OUTLINED IN OMNI SBCS GTEP MANUAL AND OMNI 
SBCS GTEP MANUAL AND OMNI SBCS STUDENT WORKBOOK. 
@ REVIEW EXERCISE WILL BE COMPLETED CORRECTLY IN 
ACCORDANCE WITH PASS/FAIL CRITERIA OF THIS TRAINING 
ORGANIZATION. 
2.165