GTE Omni Scbs Installation And Maintenance Manual

							f”~‘ ‘.\‘\/‘!:  :‘\Laboratory Activity 
- Package C Data Base
Adminstration (5.3) (Continued)
GTE aww SEESPART 3: DIRECT INWARD DIALING
I.PRIOR TO PROGRAMMING, EMULATE A DID LINE BY PUNCHING THE TIP/RING WIRES FROM A SLT TO THE TIP/RING
WIRES OF A LOOP TIE TRUNK CIRCUIT (USE EQUIPMENT NUMBER 160).
2.USE THE CMC-250 TO ASSIGN A DID TRUNK USING THE FOLLOWING PARAMETER VALUES:
EQUIPMENT NUMBER (PI) = 160
TYPE OF TRUNK (P2) = 13 (LOOP DIAL)
TRUNK GROUP NUMBER (P3) = 57
OPERATION MODE (P4) = 1 (INCOMING)
SIGNALING 
(85) = 1 (FIXED)
START MODE (P6) = 3 (IMMEDIATE)
3.ASSIGN COS/COR TO THE DID TRUNK LINE WITH CMC-252, USING THE FOLLOWING PARAMETERS VALUES:
TRUNK GROUP NUMBER (PI) = 57
DAY COS (P2) = 1
NIGHT COS (P3) = 16
DAY COR (P4) = 1NIGHT COR (P5) = 16
4.ASSIGN THE RECEIVED DI,GIT LENGTH AND PREFIX CODE TO THE DID TRUNK WITH CMC-430, USING THE FOLLOWING
PARAMETER VALUES:TRUNK GROUP NUMBER (PI) = 57
RECEIVED DIGIT LENGTH (P2) = 3 (RECIEVED DIGIT LENGTH FROM CO PROVIDING DID)
PREFIX CODE (P3) = BLANK
DISA DIRECTORY NUMBER = 123 (SIMULATED)
DISA AUTHORIZATION CODE = 456 (SIMULATED)
5.97 
						

							Laboratory Activity - Package C Data Base
Adminstration (5.3) (Continued)
GTE OMNU a3cs
PART 4:KEY SYSTEM FEATURES
1. REMOVE ATTENDANT CONSOLE.
2.COLD RESTART THE SYSTEM.
3.CHECK/CONFIRM KEY SYSTEM FEATURE CHANGES ON EKT INSTRUMENT BUTTONS.
5.98 
						

							Review Exercise - Package C
Data Base 
Adminstration(5.3)INSTRUCTIONS: THE FOLLOWING EXERCISE CONSISTS OF MULTIPLE CHOICE, TRUE/FALSE, 
FILL IN THE
BLANK, OR MATCHING TYPE QUESTIONS. ALL AVAILABLE RESOURCES (I.E., STUDENT WORKBOOK, NOTES,
AND GTEP MANUAL) MAY BE USED AS REFERENCES. SUBMIT EXERCISE TO INSTRUCTOR FOR GRADING WHEN
LAST QUESTION HAS BEEN COMPLETED.
1.WHAT INSTALLATION OR DATA BASE PROGRAMMING STEPS ARE REQUIRED TO ALLOW A PREVIOUSLY
INSTALLED 
BLF/DSS MODULE TO FUNCTION AS A ROOM STATUS INDICATOR?
2.(TRUE OR FALSE) A TRUNK GROUP WITH AN INCOMING CALL TERMINATION PRIORITY OF 1WOULD BE ANSWERD BY THE ATTENDANT CONSLE BEFORE ANOTHER TRUNK GROUP WITH A PRIORITY
OF 3.3. 
CMC-IS USED TO CREATE A NIGHT ANSWER GROUP FOR AN ATTENDANT CONSOLE OVERFLOW
STATION, THEN TO ASSIGN “ALL TENANTS” TO BE ANSWERED BY THE OVERFLOW STATION.
4. THE
FEATURE BUTTON MUST BE ASSIGNED TO EITHER THE ATTENDANT
CONSOLE OR CSD DESIGNATED TO SERVE AS THE HOTEL/MOTEL FRONT DESK CONSOLE.
5.“AUTOMATIC WAKE-UP REGISTRATION/CANCELLATION BY GUEST ROOM” IS AN EXAMPLE OF A
MESSAGE WHICH CAN BE RECORDED BY THE HOTEL/MOTEL PRINTER.
6.THE DTMF AUTHORIZATION CODE REQUIRED BY DISA USERS IS ASSIGNED WITH CMC-
5.99 
						

							ew Exercise = Package CDntinued)
7.
8.
9.
10.CMC-430 ASSIGNS 
DISA DIRECTORY NUMBERS AND AN AUTHORIZATON CODE TO A
TRUNK LINE.
A CS-10 OR CS-20 WHICH WILL SERVE AS A VOICE STATION ASSOCIATED WITH A DIU MUST BE
ASSIGNED WITH 
CMC-, AND HAVE THEFEATURE BUTTON ASSIGNED
WITH CMC-203.
EKT INSTRUMENTS CONNECTED TO CARD SLOT
RING ON ALL INCOMING CALLS IN A KEY
TELEPHONE BUTTON ARRANGEMENT.
MATCH EACH OF THE FOLLOWING CMC COMMANDS WITH ITS CORRECT FUNCTION:
CMC-223
A. ASSIGNS TRUNK 
COSICOR TO DID TRUNKS
CMC-355
B. ASSIGNS 
DISA STANDARD TO A GROUND STRAT TRUNK
CMC-252
C. ASSIGNS GUEST ROOM NUMBERS TO ROOM STATUS INDICATOR LAMPS
CMC-231D. ASSIGNS ATTENDANT CONSOLE SERVICES TO FEATURE BUTTONS
CMC-250E. ASSIGNS DATA STATION ATTRIBUTES (Ill) AND RS-232-C 
SlGNAL MODES
5.100 
						

							PACKAGE C
MAINTENANCE
5.101 
						

							5.4 EnablingObiective
GIVEN:0
0
0
0
0GTE 
OMNI SBCS
GTE 
OMNI SBCS PACKAGE C EQUIPMENT AND PERIPHERALS
ATTENDANT CONSOLE (ASSIGNED AS MASTER CONTROL TELEPHONE IN
DATA BASE)GTE 
OMNI SBCS COURSE AND SITE DOCUMENTATION PACKAGE
REVIEW EXERCISE
ACTION:
CRITERIA:
0
Q
6
0
USE ATTENDANT CONSOLE AS AN ALTERNATE MASTER CONTROL TELEPHONEFOR DATA BASE 
ADMINSTRATION AND MAINTENANCE TASKS.
IDENTIFY FUNCTIONSAND APPLICATIOtiS OF PACKAGE C CMC MAINTENANCE
COMMANDS.
MODIFY PARAMETER VALUES FOR PACKAGE C CMC MAINTENANCE
COMMANDS.
USE ATTENDANT CONSOLE AND DATA INTERFACE UNIT DIAGNOSTIC TESTS TOIDENTIFY INSTRUMENT MALFUNCTIONS.
COMPLETE REVIEW EXERCISE.
TASKS WILL BE PERFORMED IN ACCORDANCE WITH PROCEDURES OUTLINEDIN 
OMNI SBCS GTEP MANUAL AND OMNI SBCS STUDENT WORKBOOK.
REVIEW EXERCISE WILL BE COMPLETED CORRECTLY IN ACCORDANCE WITHPASS/FAIL CRITERIA OF THIS TRAINING ORGANIZATION.0
5.102 
						

							Attendee Assignment as Master
e1 DESCRIPTION 1
.
A MAXIMUM OF TWO ATTENDANT CONSOLES CAN BE IDENTIFIED IN SYSTEM AS HAVING MASTER
CONTROL TELEPHONE (MCT) CAPABILITIES FOR DATA BASE ADMINSTRATION AND
MAINTENANCE ACTIVITIES..
ATTENDANT CONSOLE FIRST MUST BE PLACED IN THE POSITION BUSY MODE TO FUNCTION AS
AN MCT.
1.ASSIGN OR CANCEL ATTENDANT CONSOLE DIRECTORY NUMBER
AS MCT WITH CMC-702:.MCT NUMBER 
(Pl) - (1 - 4)
.
DIRECTORY NUMBER OF MCT ATTENDANT CONSOLE (P2)
(ATTENDANT CONSOLE ACCESS (0) + ATTENDANT CONSOLE
NUMBER)
NOTE: ATTEMPTS TO DELETE THE MCT BEING USED TO MAKE ENTRIES
WILL BE DENIED BY DATA BASE.ICMC = 702
Pl: 4
P2: 015.103 
						

							Attehdent Console Operation as
Master Control 
ITelepPROCEDURE
1.
2.
3.
4.
5.PLACE ATTENDANT CONSOLE IN POSITION BUSY MODE BY DEPRESSING THE POSITION BUSY FEATURE BUTTON. ANY
CALLS IN PROCESS MUST BE CLEARED BEFORE POSITION BUSY MODE CAN BE ACTIVATED.
ENTER APPROPRIATE HIGH OR LOW LEVEL SECURITY CODE USING KEYBOARD OF ATTENDANT CONSOLE
(PREVIOUSLY ASSIGNED AS MCT) WHILE ON-HOOK AND IN IDLE STATE.
AT COMMAND PROMPT, ENTER APPROPRIATE CMC COMMAND AND PRESS SELECT (ATTENDANT CONSOLE’S
DEFAULT INCOMING FEATURE BUTTON).
ENTER PARAMETER VALUES USING ATTENDANT CONSOLE‘S NUMERIC KEYPAD AND DESIGNATED PROGRAM
FUNCTION BUTTONS (ILLUSTRAED ABOVE).
PRESS RELEASE, THEN TERMINATE PROGRAM FUNCTION BUTTONS. PRESS POSITION BUSY FEATURE BUTTON TO
RETURN TO NORMAL CALL PROCESSING MODE AS AN ATTENDANT CONSOLE.
5.104 
						

							Student Notes
5.105 
						

							Attendent Console
Instrumentiagnostics
.ATTENDANT CONSOLE MUST BE TESTED OFF-LINE.0THE FOLLOWING TESTS CAN BE PERFORMED:
-BUTTON AND KEYPAD TEST
- LED LAMP TEST
- LCD DISPLAY TEST
- AUDIBLE TONE TEST
1.
2.
3.
4.
5.
6.UNPLUG TELEPHONE CORD FROM MODULAR JACK IN BACK OF ATTENDANT CONSOLE.
PRESS 1 and 3 KEYS SIMULTANEOUSLY.
PLUG TELEPHONE CORD INTO MODULAR JACK WHILE KEEPING THE 1 AND 3 KEYS PRESSED.
WHEN STEP 3 IS COMPLETED, PRESS ANY KEY TO ELIMINATE 
lNlTlALSIGNAL(INDICATING INSTRUMENT IS
IN DIAGNOSTIC MODE WITH ALL LED LAMPS FLASHING AND TONE RINGER SOUNDING).
PRESS APPROPRIATE TEST EXECUTION KEYS (REFER TO TABLES ON FOLLOWING PAGES) AND MONITOR
VISUAL AND AUDIBLE RESULTS. IF RESULTS VARY FROM THOSE LISTED, RETURN DEFECTIVE INSTRUMENT
FOR REPAIR.
TO RETURN TO NORMAL CALL PROCESSING MODE, REMOVE TELEPHONE CORD AND THEN REPLACE IN
MODULAR JACK.
5.106