GTE Omni Scbs Installation And Maintenance Manual

							-*, SC’-.> , .,--.. 
GTE OMNi SLXS 
INSTRUCTIONS: THE FOLLOWING EXERCISE CONSISTS OF MULTIPLE CHOICE, TRUE/FALSE, FILL 
IN THE BLANK, OR MATCHING TYPE QUESTlONS. ALL AVAILABLE RESOURCES (I.E. STUDENT 
WORKBOOK, NOTES, AND GTEP MANUAL) MAY BE USED AS REFERENCES. SUBMIT EXERCISE TO 
INSTRUCTOR FOR GRADING WHEN LAST QUESTION HAS BEEN COMPLETED. 
1. THE DEFAULT STANDARD TERMINATING TRUNK GROUP NUMBER FOR CO TRUNKS IS ~ . 
2. EKT INSTRUMENTS CAN HAVE ~ 
TERMINATING TRUNK GROUP NUMBERS ASSIGNED TO 
EACH BUTTON. 
3. THE FLAG DESIGNATING PERSONAL LINES IS SET TO 
AND FOR KEY SYSTEMS 
AT CMC-253, P3. 
4. HOW IS THE “RINGING/NO RINGING” OPTION PROGRAMMED FOR A TRUNK TERMINATION 
LINE BUTTON? 
5. WHAT STEPS MUST BE PERFORMED BEFORE A KEY SYSTEM LINE CAN BE ASSIGNED TO A 
BUTTON WITH CMC-203? 
6. IN WHAT TERMINATING TRUNK GROUP WAS THE PERSONAL LINE PLACED DURING THE LAB 
ACTIVITY? 
7. A PERSONAL LINE RESERVES ONE TRUNK FOR INCOMING AND/OR OUTGOING CALLS FOR A 
SPECIFIC 
STATION. 
2.98  
						

							eview Exercise 
- Programming Trunk 
Termination 
(2.4) (Continued) 
8. 
9. 
10. 
11. 
12. 
13. 
14. 
15. 
IF A CUSTOMER DESIRES ONE OR MORE EKT STATIONS TO HAVE ACCESS TO THE SAME TRUNK 
LINE THROUGH EKT BUTTONS, A 
TRUNK TERMINATION 
SHOULD BE PROGRAMMED. 
THE SYSTEM WILL ALLOW A MAXIMUM DIRECT IN-LINES PER TRUNK GROUP. 
A DIRECT IN-LINE CAN BE ASSIGNED TO BOTH 
OR 
TYPES OF STATION 
INSTRUMENTS. 
CMC- 
IS USED TO ASSIGN OR REMOVE A DIRECT-IN LINE FROM A SPECIFIC STATION. 
A MAXIMUM OF 
POOLED INCOMING TRUNK LINES MAY BE ASSIGNED TO A 
TERMINATING TRUNK GROUP. 
A POOLED 
TRUNK GROUP IS A TYPE OF TRUNK TERMINATION WHERE A 
NUMBER OF OUTGOING TRUNKS FROM A SINGLE TRUNK GROUP ARE SHARED BY A 
TERMINATING TRUNK GROUP. 
HOW DOES AN SLT OR A STATION WITHOUT A LINE TERMINATION BUTTON ASSIGNMENT 
ACCESS A POOLED BOTHWAY TRUNK? 
MATCH EACH OF THE FOLLOWING CMC COMMANDS WITH ITS CORRECT DESCRIPTION: 
CMC-203 
A. DIRECT IN-LINE ASSIGNMENT 
CMC-250 B. TRUNK ASSIGNMENT 
CMC-253 
C. EKT BUTTON ASSIGNMENT 
CMC-307 
D. TERMINATING TRUNK GROUP ASSIGNMENT. 
2.99  
						

							DATA BASE ADMINISTRATION 
Programming Service 
Functions 
2.100  
						

							2.5 Enabling bjective 
GIVEN: 
. GTE OMNI SBCS 
. GTE OMNI SBCS PERIPHERALS 
. PORTABLE MAINTENANCE PANEL 
e GTE OMNI SBCS COURSE AND SITE DOCUMENTATION PACKAGE 
. LABORATORY ACTIVITY 
- PROGRAMMING SERVICE FUNCTIONS 
0 REVIEW EXERCISE 
ACTION: 
l USE OMNI SBCS PROGRAMMING TOOLS AND EQUIPMENT 
TO: 
- ESTABLISH A SYSTEM SPEED CALLING DIRECTORY. 
- ASSIGN STATIONS TO HUNT AND PICKUP GROUPS. 
- INSTALL AND ASSIGN SYSTEM MUSIC-ON-HOLD FEATURE. 
- CREATE HOT LINE SERVICE. 
- ASSIGN INTERNAL SPEAKER PAGING GROUPS. 
- ESTABLISH NIGHT RINGING ANSWER STATION. 
. COMPLETE REVIEW EXERCISE. 
CRITERIA: . DEMONSTRATION OF ABOVE TASKS IN ACCORDANCE WITH 
PROCEDURES OUTLINED IN GTEP MANUAL AND OMNI SBCS STUDENT 
WORKBOOK. 
. REVIEW EXERCISE WILL BE COMPLETED CORRECTLY IN 
ACCORDANCE WITH PASS/FAIL CRITERIA OF THIS TRAINING 
ORGANIZATION. 
2.101  
						

							. A MAXIMUM OF 100 DIRECTORY NUMBERS CAN BE PLACED IN A 
SYSTEM SPEED CALLING DIRECTORY. STATION USER DIALS AN ENTRY 
CODE TO ACCESS NUMBER ON SPEED CALLING LIST. 
. DEFAULT STANDARD ACCESS CODE FOR SYSTEM SPEED CALLING 
NUMBER IS ##. 
(PROCEDURE1 
CMC=300 
P3: 9361111 
1. USE CMC-300 TO ASSIGN, CHANGE OR DELETE: 
@ SYSTEM SPEED CALLING USER ENTRY CODE (PI) 
@ ACCESS CODE (SYSTEM ACCESS CODES FOR CO, FX, WATS, TIE 
LINE, SCC OR LCR) (P2) 
0 SEND NUMBER (P3) 
2. USE CM6400 TO CHANGE ACCESS CODE NUMBERING PLAN. 
2.102  
						

							Programming Service Functions/ 
Station Hunt Group Assignment 
. STATION DIRECTORY NUMBER MAY BE ASSIGNED TO ONE OF THREE TYPES OF HUNT GROUPS: 
- CIRCULAR - IF CALLED DIRECTORY NUMBER IS BUSY, ALL STATIONS WITHIN GROUP ARE TRIED 
IN TURN UNTIL AN IDLE STATION IS FOUND. IF CALLED DIRECTORY NUMBER IS NOT REACHED 
AFTER CIRCULAR HUNTING, CALLING PARTY IS CONNECTED TO BUSY TONE. 
- TERMINATING - DIRECTORY NUMBERS WITHIN GROUP ARE ASSIGNED A PRIORITY. WHEN 
CALLED STATION IS BUSY, IDLE STATION IS HUNTED IN ORDER OF PROGRAMMED PRIORITY. 
CALLING PARTY IS CONNECTED TO BUSY TONE IF NO IDLE STATION IS FOUND. 
- PILOT - DIRECTORY NUMBER IS ASSIGNED AS PILOT STATION. IF PILOT IS BUSY, ALL STATIONS 
WITHIN GROUP ARE TRIED. IF NO IDLE STATION IS FOUND, CALLING PARTY IS CONNECTED TO 
BUSY TONE. IF OTHER DIRECTORY NUMBERS ARE BUSY, NO GROUP HUNT OCCURS SINCE HUNT 
MUST ORIGINATE FROM PILOT STATION. 
@ SYSTEM DEFAULT CAPACITY ALLOWS FOR MAXIMUM OF 10 VOICE OR DATA HUNT GROUPS WITH 
UP TO 16 DIRECTORY NUMBER MEMBERS IN EACH HUNT GROUP.* 
piiGiq 
1. USE CMC 301 TO ADD, CHANGE OR REMOVE: 
CMC=301 
. STATION HUNTING GROUP NUMBER (Pl) P1:2 P4:2 
P2: 3 
l TERMINATING ORDER (P2) P3: 412 
. DIRECTORY NUMBER OF HUNT GROUP (P3) 
l HUNTING TYPE (P4) 
NOTES: 1. WHEN ENTERING PARAMETER FOR TERMINATING ORDER OF PILOT HUNT GROUP, FIRST 
DIRECTORY NUMBER ENTERED IS DESIGNATED PILOT STATION. 
2. EXISTING ENTRIES MUST BE REMOVED BEFORE CHANGING HUNT GROUP 
ASSIGNMENTS. 
* PACKAGE C ALLOWS 20 VOICE HUNT GROUPS. 
2.103  
						

							DESCRIPTION 1 
e SYSTEM DEFAULT CAPACITY ALLOWS FOR MAXlMUM OF 10 PICKUP 
GROUPS WITH UP TO 32 DIRECTORY NUMBER MEMBERS IN EACH 
PICKUP GROUP. * 
pii6ziq 
1. USE CMC-362 TO ADD CHANGE OR DELETE: 
0 PICKUP GROUP NUMBER (PI) 
@ DIRECTORY NUMBER OF PICKUP GROUP MEMBER (P2) 
NOTE: EXISTING ENTRIES MUST BE DELETED BEFORE CHANGING PICKUP 
GROUP DIRECTORY NUMBERS. CHANGE (CHG) PROGRAM 
FUNCTION IS USED TO ASSIGN NEW ENTRY. 
* PACKAGE C ALLOWS 26 PICKUP GROUPS. 
2.1Q4  
						

							amming Service Functions/ 
ine Station Assignment 
DESCRIPTION 1 
@ HOT LINE FEATURE ALLOWS FOR SINGLE-LINE STATIONS TO BE PROGRAMMED TO 
AUTOMATICALLY SIGNAL A TERMINATING INTERNAL STATION WHENEVER IT GOES 
OFF-HOOK. 
@ DESIGNATED HOT LINE STATIONS CAN ACCEPT TERMINATING CALLS AND USE 
CONSULTATION HOLD, TRANSFER, AND OTHER SERVICES. 
0 SYSTEM DEFAULT CAPACITY ALLOWS FOR A MAXIMUM OF 10 SYSTEM HOT LINES 
FOR VOICE (PACKAGES A AND B) AND 40 FOR DATA (PACKAGE B). 
p&Giiq 
1. USE CMC-304 TO ASSIGN OR REMOVE: 
@ HOT LINE NUMBER (PI) 
. ORIGINATING STATION DIRECTORY NUMBER (P2) 
0 TERMINATING STATION DIRECTORY NUMBER (P3) 
CMC= 304  CMC= 304 
Pl: 2  Pl: 2 
P2: 500  P2: 500 
P3: 523  P3: 523 
NOTE: EXISTING ENTRIES MUST BE DELETED BEFORE CHANGING HOT 
LINE STATION ASSIGNMENTS. CHANGE (CHG) PROGRAM FUNCTION 
IS USED TO ASSIGN NEW ENTRY. 
* PACKAGE C ALLOWS 20 SYSTEM HOT LINES FOR VOICE AND 40 FOR DATA. 
2.105  
						

							) DESCRIPTION 
0 INTERNAL PAGlNG IS ACCOMPLISt-lED BY UTILIZING SPEAKERS ON EKT 
INSTRUMENTS. 
6 PROXIMITY OF EKT INSTRUMENTS TO USERS SERVED WITHIN EACH 
GEOGRAPHIC PAGING ZONE MUST BE CONSIDERED WMEN ESTABLISHING 
PAGING ZONES. 
@ SYSTEM DEFAULT CAPACITY ALLOWS FOR MAXIMUM OF NINE PAGING ZONES 
(GROUPS) WITH UP TO FOUR EKT DIRECTORY MEMBERS ASSIGNED TO EACH 
ZONE. 
1. USE CMC-303 TO ADD OR REMOVE: 
CMC=303 
@ PAGING GROUP (PI) 
@ DIRECTORY NUMBER OF A PAGING GROUP MEMBER (P2) 
I- P1:2 
P2:346 
NOTES: 1. EXISTING ENT UST BE DELETED WITH 
(RMV) PROGRA 
FUNCTION BEFORE CHANGING PAGING GROUPS ASSIGNMENTS. ADD 
(AQD) PROGRAM FUNCTION IS USED TO ASSIGN NEW ENTRY. 
2. EXTERNAL PAGING WILL BE COVERED IN MODULE BW. 
2.106  
						

							1 DESCRIPTION 1 
@ MUSIC-ON-HOLD SERVICE REQUIRES CUSTOMER PROVIDED 600 OHM IMPEDANCE 
MUSIC SERVICE 
PROCEDURE * 
1. USE CMC-250 TO ASSIGN TYPE OF TRUNK. 
2. 
USE CMC-305 TO ASSIGN: 
. EQUIPMENT NUMBER FOR MUSIC SOURCE (PI) 
CMC=305 
P1:182 
L-J 
* ASSUMES TRUNK CARD (4BWC) HAS BEEN SEATED IN APPROPRIATE SLOT AND 
CUSTOMER PROVIDED MUSIC SOURCE HAS BEEN PHYSICALLY CONNECTED TO 
DESIRED SLOT AND CIRCUIT. 
2.107