Xerox 1632 2240 3535 Color Carrera Manual

							6/02
2-131 DC1632/2240
8-622, 8-623
Status Indicator RAPs Prelaunch Training/Review
8-622 Regicon Data Overflow (A1 Patch X)At A1 patch detection, the XSO correction setting value for either Y, M, C, or K exceeds the set-
ting range (NVM value 0 to 472). 
NOTE: Status Code not displayed on UI. Machine operation continues.ProcedureCheck the IBT Belt and Drum for a scratch or contamination. The check is OK.
YN
Replace as required.
Perform DC685 Color Registration (ADJ 9.6). 
8-623 Regicon Data Overflow (A2 Patch Y)At A2 patch detection, the YSO correction setting value of either Y, M, C, or K exceeds the set-
ting range (NVM value 0 to 474). 
NOTE: Status Code not displayed on UI. Machine operation continues.ProcedureCheck the IBT Belt and Drum for a scratch or contamination. The check is OK.
YN
Replace as required.
Perform DC685 Color Registration (ADJ 9.6).  
						

							6/02
2-132DC1632/2240
8-624, 8-625
Prelaunch Training/Review Status Indicator RAPs
8-624 Regicon Data Overflow (Patch Magnification)MAG Adjusted Set Point of operation results for each of Y,M,C exceeded the set range (NVM
value: 0~1432).
NOTE: Status Code not displayed on UI. Machine operation continues.ProcedureCheck the IBT Belt and Drum for a scratch or contamination. The check is OK.
YN
Replace as required.
Go to ADJ 9.6 Color Registration dC685.
8-625 Regicon Sample Block (A1 Patch-rear)At A1 (IN) patch detection, the number of the sample blocks does not reach the specified num-
ber. 
NOTE: Status Code not displayed on UI. Machine operation continues.ProcedureCheck the IBT Belt and Drum for a scratch or contamination. The check is OK.
YN
Replace as required.
Perform DC685 Color Registration (ADJ 9.6).  
						

							6/02
2-133 DC1632/2240
8-626, 8-627
Status Indicator RAPs Prelaunch Training/Review
8-626 Regicon Sample Block (A1 Patch-front)At A1 (OUT) patch detection, the number of the sample blocks does not reach the specified
number. 
NOTE: Status Code not displayed on UI. Machine operation continues.ProcedureCheck the IBT Belt and Drum for a scratch or contamination. The check is OK.
YN
Replace as required.
Perform DC685 Color Registration (ADJ 9.6). 
8-627 Regicon Sample Lateral (A1 Patch-rear)At A1 (IN) patch detection, the Fast Scan scan position of CYAN color that is the standard for
the rest is incorrect. (Against the MOB SENSOR, the center position of the CYAN pattern is
shifted by ±500µm or more.)
NOTE: Status Code not displayed on UI. Machine operation continues.ProcedureCheck the IBT Belt and Drum for a scratch or contamination. The check is OK.
YN
Replace as required.
Perform DC685 Color Registration (ADJ 9.6).  
						

							6/02
2-134DC1632/2240
8-628, 8-629
Prelaunch Training/Review Status Indicator RAPs
8-628 Regicon Sample Lateral (A1 Patch-front)At A1 (OUT) patch detection, the scan position of CYAN color that is the standard for the rest is
incorrect. (Against the MOB SENSOR, the center position of the CYAN pattern is shifted by
±500µm or more.?
NOTE: Status Code not displayed on UI. Machine operation continues.ProcedureCheck the IBT Belt and Drum for a scratch or contamination. The check is OK.
YN
Replace as required.
Perform DC685 Color Registration (ADJ 9.6). 
8-629 Regicon Skew (Patch Y)During A1 Patch detection, skew deviation for Y exceeded tolerance.
NOTE: Machine operation continues. Status Code not displayed on UI. Status Code logged in
History.Initial ActionsClean MOB Sensor.ProcedureCheck the IBT Belt and Drum for a scratch or contamination. The check is OK.
YN
Replace as required.
Perform DC685 Color Registration (ADJ 9.6).  
						

							6/02
2-135 DC1632/2240
8-630, 8-631
Status Indicator RAPs Prelaunch Training/Review
8-630 Regicon Skew (Patch M)During A1 Patch detection, skew deviation for M exceeded tolerance.
NOTE: Machine operation continues. Status Code not displayed on UI. Status Code logged in
History.Initial ActionsClean MOB Sensor.ProcedureCheck the IBT Belt and Drum for a scratch or contamination. The check is OK.
YN
Replace as required.
Perform DC685 Color Registration (ADJ 9.6). 
8-631 Regicon Skew (Patch K)During A1 Patch detection, skew deviation for K exceeded tolerance.
NOTE: Machine operation continues. Status Code not displayed on UI. Status Code logged in
History.Initial ActionsClean MOB Sensor.ProcedureCheck the IBT Belt and Drum for a scratch or contamination. The check is OK.
YN
Replace as required.
Perform DC685 Color Registration (ADJ 9.6).  
						

							6/02
2-136DC1632/2240
8-900
Prelaunch Training/Review Status Indicator RAPs
8-900 Static JamWhen the machine power is turned off then on before a paper path fault is cleared, an 8-900
fault will be displayed. A voltage drop or interruption can also cause this fault.   Initial Actionsï Check the entire paper path for paper or obstructions.
ï Clean all the paper path sensors.
ï Check the Fault History for the last paper path fault. Go to that paper path fault RAP. ProcedureIn sequence, enter the following dC330 codes:
Block and unblock each sensor
ï 8-100 Tray 1 Mis-feed, (7-105).
ï 8-106 Tray 2 Mis-feed, (7-110).
ï 8-102 Tray 3 Mis-feed, (7-115).
ï 8-103 Tray 4 Mis-feed, (7-119).
ï 8-104 Registration Sensor, (8-175).
ï 9-201 POB On Jam, (8-164)
The display for each code changes.
YN
Go to the appropriate paper path fault RAP. 
Check the machine input voltage, if the problem continues, replace the ESS PWB (PL 13.1). 
						

							6/02
2-137 DC1632/2240
9-342
Status Indicator RAPs Prelaunch Training/Review
9-342 2nd BTR ContactThe 2nd BTR did not reach the contact position.Initial Actionsï Clean the 2nd BTR Retract Sensor and check for damage.
ï Check the 2nd BTR transmission gears for breakage.ProcedureIn sequence, enter the following: dC330 [009-051] then dC330 [009-052]. The 2nd BTR con-
tacts and retracts. 
YN
Go to OF 99-6 Motor Open RAP.
 Go to OF 99-2 Transmissive Sensor RAP.
Figure 1 2ND BTR Retract Sensor
Figure 2 2ND BTR Retract Motor 
						

							6/02
2-138DC1632/2240
9-343
Prelaunch Training/Review Status Indicator RAPs
9-343 2nd BTR RetractThe 2nd BTR did not reach the retract position.Initial Actionsï Clean the 2nd BTR Retract Sensor and check for damage.
ï Check the 2nd BTR transmission gears for breakage.ProcedureIn sequence, enter the following: dC330 [009-051] then dC330 [009-052]. The 2BTR contacts
and retracts. 
YN
Go to OF 99-6 Motor Open RAP.
 Go to OF 99-2 Transmissive Sensor RAP.
Figure 1 2ND BTR Retract Sensor
Figure 2 2ND BTR Retract Motor 
						

							6/02
2-139 DC1632/2240
9-348
Status Indicator RAPs Prelaunch Training/Review
9-348 1st BTR ContactThe 1st BTR did not reach the contact position.Initial Actionsï Clean the 1st BTR Retract Sensor and check for damage
ï Check the 1st BTR transmission gears for breakage
ProcedureIn sequence, enter the following: dC330 [009-054] then dC330 [009-055]. The 1st BTR con-
tacts and retracts. 
YN
Go to OF 99-6 Motor Open RAP.
 Go to OF 99-2 Transmissive Sensor RAP.
Figure 1 1ST BTR Retract Sensor
Figure 2 1ST BTR Retract Motor 
						

							6/02
2-140DC1632/2240
9-349
Prelaunch Training/Review Status Indicator RAPs
9-349 1st BTR RetractThe 1st BTR did not reach the retract position.Initial Actionsï Clean the 1st BTR Retract Sensor and check for damage
ï Check the 1st BTR transmission gears for breakage
ProcedureIn sequence, enter the following: dC330 [009-054] then dC330 [009-055]. The 1st BTR con-
tacts and retracts. 
YN
Go to OF 99-6 Motor Open RAP.
 Go to OF 99-2 Transmissive Sensor RAP.
Figure 1 1ST BTR Retract Sensor
Figure 2 1ST BTR Retract Motor