Xerox 1632 2240 3535 Color Carrera Manual

							6/02
2-401 DC1632/2240
116-714, 116-715
Status Indicator RAPs Prelaunch Training/Review
116-714  A HP-GL command error was detected[Detection Conditions]  HP-GL/2 command errorProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Correct or remove the data in the print data that causes the error.
116-715  PLW form registry errorThe PLW form data cannot be registered because of the restriction of the number of forms.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Use the Operation Panel to check the registered forms, and delete unnecessary ones. Or
delete unnecessary forms. 
						

							6/02
2-402DC1632/2240
116-718, 116-737
Prelaunch Training/Review Status Indicator RAPs
116-718  PLW form synthesis errorThe specified form is not registered.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Use a registered form, or register a necessary form.
116-737  Insufficient ART user defined areaThe user defined data (external characters, patterns, etc.) cannot be registered because of
insufficient RAM capacity.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Delete registered user defined data. Or increase the allocated capacity of the RAM. 
						

							6/02
2-403 DC1632/2240
116-738, 116-739
Status Indicator RAPs Prelaunch Training/Review
116-738  Form synthesis errorSynthesis is impossible because the size/orientation of the forms drawing is different from that
of the paper.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Select the paper with the size and orientation of the registered form.
116-739  Insufficient form/logo capacityThe form/logo data cannot be registered because of the insufficient RAM or Hard Disk space.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Use the Operation Panel to check the registered forms, and delete unnecessary ones.  Or
increase the allocated capacity of the RAM disk. 
						

							6/02
2-404DC1632/2240
116-740, 116-741
Prelaunch Training/Review Status Indicator RAPs
116-740  Value Calculation ErrorThe number calculated in the interpreter exceeded the limit value.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Remove the data that exceeds the limit value of the printer from the print data.
116-741  Form registry errorThe form data cannot be registered because of the restriction of the number of forms.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Use the Operation Panel to check the registered forms, and delete unnecessary ones. Or
delete unnecessary forms. 
						

							6/02
2-405 DC1632/2240
116-742, 116-743
Status Indicator RAPs Prelaunch Training/Review
116-742  Logo registry errorThe logo data cannot be registered because of the restriction of the number of logos.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Use the Operation Panel utility to check the registered logos, and delete unnecessary ones. Or
delete unnecessary logos with the Print command.
116-743  Form/logo size overflowThe received data (forms/logos) indicating that forms/logos cannot be registered (due to insuf-
ficient area) exceeded the registered buffer size.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Increase the form registry area size from the Operation Panel. Or install the HD.   
						

							6/02
2-406DC1632/2240
116-745, 116-746
Prelaunch Training/Review Status Indicator RAPs
116-745  Art Command ErrorThe decomposer checks the syntax error and excess of each limit value at decomposing.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Correct the command.
Change the ART command where an error has occurred.
116-746  Form synthesis errorThe specified form is not registered.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Use a registered form, or register a necessary form. 
						

							6/02
2-407 DC1632/2240
116-747, 116-748
Status Indicator RAPs Prelaunch Training/Review
116-747  White page detectedAfter subtracting the paper margin from the valid coordinate area, the result of the calculation
will be negative.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Again, switch power off then on.  No actions required.
116-748  White page detected[Detection Conditions]  There is no drawing data in the page data.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Again, switch power off then on.  No actions required 
						

							6/02
2-408DC1632/2240
116-780, 116-790
Prelaunch Training/Review Status Indicator RAPs
116-780  Attached document failure of email to XXXProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Attached document failure of email to XXX
No actions required.
116-790  Printed without the staplerProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Printed without the stapler
No actions required. 
						

							6/02
2-409 DC1632/2240
OF 1-1
Status Indicator RAPs Prelaunch Training/Review
OF 1-1 +3.5 VDC+3.5 VDC failure.ProcedurePerform following:
ï Remove Rear Cover (REP 14.2). 
ï Tilt out HVPS Chassis (REP 1.6).
Check that power is switched off.  Measure resistance of fuse on +3.5V LVPS (Figure 1).
Resistance is 1 ohm or less.
YN
Replace +3.5V LVPS (PL 9.1).
Switch on the power.  Measure the AC voltage between the white and black wires in p15 on the
+3.5V LVPS (Figure 1).  110 or 220 VAC is measured.
YN
Go to the AC Power RAP.
Connect the black meter lead to DC COM or frame.  Measure DC voltage at p510 on the +3.5
V LVPS (Figure 1). Voltages are measured as shown.
YN
Replace the 3.5V LVPS (PL 9.1).
There is a short circuit in +3.5 VDC distribution.  Go to the +3.5 VDC Short Circuit RAP.
Figure 1 P15, P510 on +3.5V LVPS
+3.5 
VDC 
RET 
Vio
+3.5 
VDC 
GryBlack 
WireWhite 
Wire 
						

							6/02
2-410DC1632/2240
OF 1-2
Prelaunch Training/Review Status Indicator RAPs
OF 1-2 +5 VDC+5 VDC failure.ProcedurePerform following:
ï Remove Rear Cover (REP 14.2). 
ï Tilt out HVPS Chassis (REP 1.6).
Check that power is switched off.  Measure resistance of fuse on +5V LVPS (Figure 1).
Resistance is 1 ohm or less.
YN
Replace +5V LVPS (PL 9.1).
Switch on the power.  Measure the AC voltage between the black and white wires in P16 on
the +5V LVPS (Figure 1). 110 or 220 VAC is measured.
YN
Go to the AC Power RAP.
Measure the DC voltage at P511 on the +5V LVPS (Figure 1).  Voltages are measured as
shown.
YN
Replace the +5V LVPS (PL 9.1).
There is a short circuit in +5 VDC distribution.  Go to the +5 VDC Short Circuit RAP.
Figure 1 P16, P511 on +5V LVPS
+5VDC 
RET
Vio (all) +5VDC 
Orn (3)