Xerox 1632 2240 3535 Color Carrera Manual

							6/02
2-361 DC1632/2240
103-372, 103-701
Status Indicator RAPs Prelaunch Training/Review
103-372 IOT Sc Soft FailureIOT Controller software failure was detected.ProcedureTurn the power OFF/ON. The fault is cleared.
YN
Reinstall the ESS software. 
If the problem continues, replace the ESS PWB (PL 13.1).
Return to Service Call Procedures.
103-701 Changed Output Bin: Side To CenterThe output tray was changed (Side Tray to Center Output Tray).ProcedureNo action required. 
						

							6/02
2-362DC1632/2240
103-702
Prelaunch Training/Review Status Indicator RAPs
103-702 Changed Output Bin: Finisher To CenterThe output tray was changed (Finisher Tray to Center Output Tray).ProcedureNo action required. 
						

							6/02
2-363 DC1632/2240
116-200, 116-201
Status Indicator RAPs Prelaunch Training/Review
116-200  Main PWBA ICAn error was detected in the IC in the ESS PWB.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Replace the ESS PWB (PL 13.1).
116-201  HDThe HD was not booted due to a HD error detected on bootingProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Run the HD Diag (DC355).
If the problem continues, replace the HD (PL 13.1)
If the problem continues, replace the ESS PWB (PL 13.1) 
						

							6/02
2-364DC1632/2240
116-206, 116-207
Prelaunch Training/Review Status Indicator RAPs
116-206  TimerA timer error was detected.ProcedureReplace the ESS PWB (PL 13.1).
116-207  Ethernet BoardA timer error was detected in the Ethernet board.ProcedureThis code is not supposed to occur. 
						

							6/02
2-365 DC1632/2240
116-209, 116-310
Status Indicator RAPs Prelaunch Training/Review
116-209  ESS PS-1 ROM CheckA failure was detected when the ESS PS-1 ROM was checked.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Pull out and insert the PS-1 ROM (PL 13.1).
If the problem continues, replace PS-1 ROM (PL 13.1).  
116-310  ESS PS-2 ROM CheckA failure was detected when the ESS PS-2 ROM was checked.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Pull out and insert the PS-2 ROM (PL 13.1).
If the problem continues, replace PS-2 ROM (PL 13.1).   
						

							6/02
2-366DC1632/2240
116-311, 116-314
Prelaunch Training/Review Status Indicator RAPs
116-311  ESS Font ROM DIMM #3 CheckA failure was detected when the ESS FONT ROM DIMM #3 was checked.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Pull out and insert the ESS FONT ROM DIMM #3.
If the problem continues, replace the ESS FONT ROM DIMM #3.  
116-314  Ethernet AddressA Ethernet error was detected.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Switch power off then on.
If the problem continues, replace the ESS PWB (PL 13.1). 
						

							6/02
2-367 DC1632/2240
116-315, 116-316
Status Indicator RAPs Prelaunch Training/Review
116-315  ESS RAM DIMM #1 W/R CheckA failure was detected during W/R of the ESS RAM DIMM #1.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Pull out and insert the ESS RAM DIMM #1.
If the problem continues, replace the ESS RAM DIMM #1.  
116-316  ESS RAM DIMM #2 W/R CheckA failure was detected during W/R of the ESS RAM DIMM #2.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Pull out and insert the ESS RAM DIMM #2.
If the problem continues, replace the ESS RAM DIMM #2.   
						

							6/02
2-368DC1632/2240
116-317, 116-318
Prelaunch Training/Review Status Indicator RAPs
116-317  Standard ROM DIMM CheckAn error was detected when the standard ROM DIMM was checked.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Pull out and insert the standard ROM DIMM.
If the problem continues, replace the standard ROM DIMM.
116-318  Option ROM DIMM Check An error was detected when the optional ROM DIMM was checked.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Pull out and insert the optional ROM DIMM.
If the problem continues, replace the optional ROM DIMM. 
						

							6/02
2-369 DC1632/2240
116-319, 116-320
Status Indicator RAPs Prelaunch Training/Review
116-319  SerialThere is no serial board at the serial board initialization failure.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Reinstall the serial board.
116-320  STREAMZ SoftFatal error of the STREAMZ.  Due to an error during the software processing, the subsequent
processes cannot be performed.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Perform re-installation of the ESS software.
If the problem continues, replace the ESS PWB (PL 13.1). 
						

							6/02
2-370DC1632/2240
116-321, 116-323
Prelaunch Training/Review Status Indicator RAPs
116-321  System SoftDue to an error during the software processing, the subsequent processes cannot be per-
formed.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Perform re-installation of the ESS software.
If the problem continues, replace the ESS PWB (PL 13.1).
116-323  ESS NVRAM W/R CheckAn error was detected at the W/R check of the NVM in the ESS PWB.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Replace the ESS PWB (PL 13.1).