Xerox 1632 2240 3535 Color Carrera Manual

							6/02
2-311 DC1632/2240
102-316, 102-317
Status Indicator RAPs Prelaunch Training/Review
102-316  Send Request Queue Full SIOOver the upper limit of the processing capability to send data from the Panel to the Controller. ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Perform re-installation of the software.
102-317  Receive Message Queue FullThe data received from the Controller exceeded the upper limit of the processing capability in
the Panel.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Perform re-installation of the software. 
						

							6/02
2-312DC1632/2240
102-318, 102-319
Prelaunch Training/Review Status Indicator RAPs
102-318  Receive Finish Queue FullThe data received from the Controller exceeded the upper limit of the processing capability in
the Panel.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Perform re-installation of the software.
102-319  Send with No ACKSerial communication failure.  Sending failure, ACK was not returned.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Perform re-installation of the software. 
						

							6/02
2-313 DC1632/2240
102-320, 102-321
Status Indicator RAPs Prelaunch Training/Review
102-320  PollingSerial communication failure.  Communication failure (polling error)ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Perform re-installation of the software.
102-321  Send MessageSerial communication failure.  Sending message error.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Perform re-installation of the software. 
						

							6/02
2-314DC1632/2240
102-322, 102-323
Prelaunch Training/Review Status Indicator RAPs
102-322  TargetSerial communication failure.  Target error.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Perform re-installation of the software.
102-323  AddressSerial communication failure.  Address error.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Perform re-installation of the software. 
						

							6/02
2-315 DC1632/2240
102-324, 102-325
Status Indicator RAPs Prelaunch Training/Review
102-324  SizeSerial communication failure.  Size errorProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Perform re-installation of the software.
102-325  Object CreationObject creation error.  The specified object failed to be created due to a setting or specifying
error on gm_create.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Perform re-installation of the software. 
						

							6/02
2-316DC1632/2240
102-326, 102-327
Prelaunch Training/Review Status Indicator RAPs
102-326  Memory OverflowMemory overflow.  The memory in the GUAM exceeded the upper limit.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Expand the memory in the GUAM.
If the problem continues, perform re-installation of the software.
102-327  Button OverflowButton overflow.  The memory for the (synchronous display) button in the GUAM exceeded the
upper limit.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Expand the memory for the button in the GUAM.
If the problem continues, perform re-installation of the software. 
						

							6/02
2-317 DC1632/2240
102-328, 102-329
Status Indicator RAPs Prelaunch Training/Review
102-328  UI Internal with Out of AreaI/F failure in the UI.  The coordination value out of the area of the displayed screen was
detected (W x H = 640 x 240)ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Check the D-RAM and ROM.
If the problem continues, perform re-installation of the software.
102-329  UI Internal with Invalid CoordinatesI/F failure in the UI.  The coordination value that cannot be displayed was detected (X = 4 times
number position)ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Check the D-RAM and ROM.
If the problem continues, perform re-installation of the software. 
						

							6/02
2-318DC1632/2240
102-330, 102-331
Prelaunch Training/Review Status Indicator RAPs
102-330  Interface with Invalid Parameter LCDInterface failure.  Incorrect parameter was detected at the Drv. I/F between the DM and LCD.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Check the D-RAM and ROM.
If the problem continues, perform re-installation of the software.
102-331  UI Internal with Invalid LED RequestI/F failure in the UI.  The request for lighting up an incorrect LED was received.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Check the D-RAM and ROM.
If the problem continues, perform re-installation of the software. 
						

							6/02
2-319 DC1632/2240
102-332, 102-333
Status Indicator RAPs Prelaunch Training/Review
102-332  Interface with Invalid Parameter CPInterface failure.  Incorrect parameter was detected at the Drv. I/F between the DM and CP.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Check the D-RAM and ROM.
If the problem continues, perform re-installation of the software.
102-333  Interface with Impossible CommunicationInterface failure.  Impossible communication with the Control Panel was detected.  H/W con-
nection failure in the Panel, or the internal connection was unable to be detected correctly.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Perform re-installation of the software. 
						

							6/02
2-320DC1632/2240
102-334, 102-335
Prelaunch Training/Review Status Indicator RAPs
102-334  Interface with Receiving Error Key CodeInterface failure.  Invalid Key Code was received from the Control Panel.  ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Repair/adjust the Control Panel (PL 18.2)
102-335  Interface with Receiving Invalid CoordinatesInterface failure.  Invalid coordination value was received from the Control Panel with a param-
eter.ProcedureSwitch power off then on. The problem continues.
YN
Return to service call procedures.
Repair/adjust the Control Panel (PL 18.2)