Xerox 1632 2240 3535 Color Carrera Manual
Have a look at the manual Xerox 1632 2240 3535 Color Carrera Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 228 Xerox manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 777
6/02
6-13 DC1632/2240General Procedures and Information Prelaunch Training/Review
710-xxx DADF NVM List
700-337 Configuration (info. On SEEPROM) - - [P, SP, CSP, CFSP (C)] Set at factory. It allocates bits in the following into P(rinter), F(ax), C(opy), S(can)
respectively and display it in that disjunction. P = 0x01, F = 0x02, C = 0x04, S = 0x08
700-338 Territory (SEEPROM) - 1~4 1=FX, 2=XC, 3=XE, 4=AP
700-339 IOT ROM Major version - - (Auto Setting)
700-340 IOT ROM Minor version - - (Auto Setting)...](http://img.usermanuals.tech/thumb/82/49005/w64_xerox-1632-2240-3535-color-carrera-service-manual-776.png "Page 777
6/02
6-13 DC1632/2240General Procedures and Information Prelaunch Training/Review
710-xxx DADF NVM List
700-337 Configuration (info. On SEEPROM) - - [P, SP, CSP, CFSP (C)] Set at factory. It allocates bits in the following into P(rinter), F(ax), C(opy), S(can)
respectively and display it in that disjunction. P = 0x01, F = 0x02, C = 0x04, S = 0x08
700-338 Territory (SEEPROM) - 1~4 1=FX, 2=XC, 3=XE, 4=AP
700-339 IOT ROM Major version - - (Auto Setting)
700-340 IOT ROM Minor version - - (Auto Setting)...")
![Page 778
6/02
6-14DC1632/2240 Prelaunch Training/Review General Procedures and Information710-006 DupMode RegiSensor On to Belt Mot.
Slowdown Step (Non CVT Mode)44 19~69 [Description] = No. of Steps after the Regi Sensor turned On and until the Belt Motor started to reduce speed in
the Non CVT Mode (Reverse & Reverse Output Loop) Regi Roll Loop Adjustment Value at Reverse & Reverse
Output = 4 +/-5mm
710-012 8.5x11LEF Threshold 2093 1993~2193 Threshold to separated the size detection of 8.5x11LEF and 8x10LEF....](http://img.usermanuals.tech/thumb/82/49005/w64_xerox-1632-2240-3535-color-carrera-service-manual-777.png "Page 778
6/02
6-14DC1632/2240 Prelaunch Training/Review General Procedures and Information710-006 DupMode RegiSensor On to Belt Mot.
Slowdown Step (Non CVT Mode)44 19~69 [Description] = No. of Steps after the Regi Sensor turned On and until the Belt Motor started to reduce speed in
the Non CVT Mode (Reverse & Reverse Output Loop) Regi Roll Loop Adjustment Value at Reverse & Reverse
Output = 4 +/-5mm
710-012 8.5x11LEF Threshold 2093 1993~2193 Threshold to separated the size detection of 8.5x11LEF and 8x10LEF....")
6/02 6-17 DC1632/2240General Procedures and Information Prelaunch Training/Review 715-229 Color Balance Default = K/Low density 4 0~8 Default Color Balance Adjustment Level K Color Low density 715-230 Color Balance Default = K/Medium density4 0~8 Default Color Balance Adjustment Level K Color Medium density 715-231 Color Balance Default = K/high density 4 0~8 Default Color Balance Adjustment Level K Color High density 715-232 Photo reproduction level 1 0~2 0 = Above Text, 1 = Normal, 2 = Above Photo 715-233 Text/Photo separation level 2 0~4 0 = Above Text, 1 = Slightly above text, 2 = Normal, 3 = Slightly above photo, 4 = Above Photo 715-234 FS Magnification Adjustment 50 0~100 Magnification fine adjustment in Fast Scan direction. Specified in units between range of 0~100. The value indi- cates the magnification adjustment with 0= -5%, 50= 0% and 100= 5% at ±5% (0.1% unit) (Adjustment at fac- tory.) 715-237 Normal Density Text (BW Copy) 128 0~256 B/W COPY Text Normal Density Adjustment 715-238 High Density Text (BW Copy) 128 0~256 B/W COPY Text Darker 3 Density Adjustment 715-239 Normal Density Text (Scan) 128 0~256 Scan Text Normal Density Adjustment 715-240 High Density Text (Scan) 128 0~256 Scan Text Darker 3 Density Adjustment 715-241 SS Not Detect Area for Platen model (Real Time AE)38 0~65535 Slow Scan Non-detection area Setup value at Real Time AE for platen model. 715-242 SS Not Detect Area for DADF model DADF mode (Real Time AE)38 0~65535 Slow Scan Non-detection area Setup value at Real Time AE for DADF model platen job. 715-243 SS Not Detect Area for DADF model Platen mode (Real Time AE)38 0~65535 Slow Scan Non-detection area Setup value at Real Time AE for DADF model DADF job. 715-244 B/W-Offset for Text/Image Platen mode (Real Time AE)10 0~255 For AE OFFSET data Platen text/photo in B/W model 715-245 B/W-Offset for Text Platen mode (Real Time AE)10 0~255 For AE OFFSET data Platen text in B/W model 715-246 B/W-Offset for Map Platen mode (Real Time AE)10 0~255 For AE OFFSET data Platen map in B/W model 715-247 B/W-Offset for Text/Image DADF Single Side mode (Real Time AE)13 0~255 For AE OFFSET data DADF Single Side Document text/photo in B/W model 715-248 B/W-Offset for Text DADF Single Side mode(Real Time AE)15 0~255 For AE OFFSET data DADF Single Side Document text in B/W model 715-249 B/W-Offset for Map DADF Single Side mode Real Time AE)13 0~255 For AE OFFSET data DADF Single Side Document map in B/W model 715-250 B/W-Offset for Text/Image DADF Duplex Side mode (Real Time AE)17 0~255 For AE OFFSET data DADF Duplex Side Document text/photo in B/W model 715-251 B/W-Offset for Text DADF Duplex Side mode (Real Time AE)17 0~255 For AE OFFSET data DADF Duplex Side Document text in B/W model 715-252 B/W-Offset for Map DADF Duplex Side mode (Real Time AE)17 0~255 For AE OFFSET data DADF Duplex Side Document map in B/W model 715-253 Color-Offset for Text/Image Platen mode (Real Time AE)15 0~255 For AE OFFSET data Platen text/photo in Color model 715-254 Color-Offset for Text Platen mode (Real Time AE)15 0~255 For AE OFFSET data Platen text in Color model 715-255 Color-Offset for Text Platen mode (Real Time AE)15 0~255 For AE OFFSET data Platen map in Color modelTable 3 Chain 715 Chain-Link Name Default Range Description
6/02 6-18DC1632/2240 Prelaunch Training/Review General Procedures and Information715-256 Color-Offset for Text/Image DADF Sin- gle Side mode (Real Time AE)17 0~255 For AE OFFSET data DADF Single Side Document text/photo in Color model 715-257 Color-Offset for Text DADF Single Side mode (Real Time AE)18 0~255 For AE OFFSET data DADF Single Side Document text in Color model 715-258 Color-Offset for Map DADF Single Side mode (Real Time AE)17 0~255 For AE OFFSET data DADF Single Side Document map in Color model 715-259 Color-Offset for Text/Image DADF Duplex Side mode (Real Time AE)17 0~255 For AE OFFSET data DADF Duplex Side Document text/photo in Color model 715-260 Color-Offset for Text DADF Duplex Side mode (Real Time AE)18 0~255 For AE OFFSET data DADF Duplex Side Document text in Color model 715-261 Color-Offset for Map DADF Duplex Side mode (Real Time AE)17 0~255 For AE OFFSET data DADF Duplex Side Document map in Color model 715-300 IIT Fail Bypass 0 0~1 0 = Fail Bypass is not available, 1 = Fail Bypass is available 715-301 SS Registration Adjustment 100 16~184 Slow Scan Direction Regi Correction Value (0.036mm/step) Adjustment at factory. 715-302 SS Magnification Adjustment 50 44~56 Slow Scan direction Magnification Correction Value (0.1%/step) Adjustment at factory. 715-400 Platen/ADF 0 0~1 0 = Platen model 1 = ADF model Adjustment at factory. 715-401 AGOC Timing 15 0~29 Time between Power ON/Energy Saver recovery and AGOC (min.) (0 = Timer not available) 715-800 lIISS/ADF Communication Fail Count Overall Total0 0~65535 Cumulative Fail Counter (Write not permitted) 715-801 IISS/ADF Communication Fail Count Since Reset0 0~65535 Cumulative Fail Counter at the previous clearing (Write not permitted) 715-802 lIISS RAM CHECK Failure Count Over- all Total0 0~65535 Cumulative Fail Counter (Write not permitted) 715-803 IISS RAM CHECK Failure Count Since Reset0 0~65535 Cumulative Fail Counter at the previous clearing (Write not permitted) 715-804 EEPROM Failure Count Overall Total 0 0~65535 Cumulative Fail Counter (Write not permitted) 715-805 EEPROM Failure Count Since Reset 0 0~65535 Cumulative Fail Counter at the previous clearing (Write not permitted) 715-806 Fan Failure Count Overall Total 0 0~65535 Cumulative Fail Counter (Write not permitted) 715-807 Fan Failure Count Since Reset 0 0~065535 Cumulative Fail Counter at the previous clearing (Write not permitted) 715-808 Scan Carriage Position Fail Count Overall Total0 0~65535 Cumulative Fail Counter (Write not permitted) 715-809 Scan Carriage Position Fail Count Since Reset0 0~65535 Cumulative Fail Counter at the previous clearing (Write not permitted) 715-810 Scan CRG Init Regi SNR Fail Count Overall Total0 0~65535 Cumulative Fail Counter (Write not permitted) 715-811 Scan CRG Init Regi Sensor Fail Count Since Reset0 0~65535 Cumulative Fail Counter at the previous clearing (Write not permitted) 715-812 PreIPS (X) Recognition Fail Count Overall Total0 0~65535 Cumulative Fail Counter (Write not permitted) 715-813 PreIPS (X) Recognition Fail Count Since Reset0 0~65535 Cumulative Fail Counter at the previous clearing (Write not permitted) 715-814 Lamp Failure Count Overall Total 0 0~65535 Cumulative Fail Counter (Write not permitted) 715-815 Lamp Failure Count Since Reset 0 0~65535 Cumulative Fail Counter at the previous clearing (Write not permitted)Table 3 Chain 715 Chain-Link Name Default Range Description
6/02 6-19 DC1632/2240General Procedures and Information Prelaunch Training/Review 715-816 CRG Over Run Fail Count Overall Total (Scan End)0 0~65535 Cumulative Fail Counter (Write not permitted) 715-817 CRG Over Run Fail Count Since Reset (Scan End)0 0~65535 Cumulative Fail Counter at the previous clearing (Write not permitted) 715-818 CRG Over Run Fail Count Overall Total (Home End)0 0~65535 Cumulative Fail Counter (Write not permitted) 715-819 CRG Over Run Fail Count Since Reset (Home End)0 0~65535 Cumulative Fail Counter at the previous clearing (Write not permitted) 715-820 CRG INIT Motor Driver Fail Count Overall Total0 0~65535 Cumulative Fail Counter (Write not permitted) 715-821 CRG INIT Motor Driver Fail Count Since Reset0 0~65535 Cumulative Fail Counter at the previous clearing (Write not permitted) 715-822 Platen AGC Channel 1 Fail Count Overall Total0 0~65535 Cumulative Fail Counter (Write not permitted) 715-823 Platen AGC Channel 1 Fail Count Since Reset0 0~65535 Cumulative Fail Counter at the previous clearing (Write not permitted) 715-824 Platen AGC Channel 2 Fail Count Overall Total0 0~65535 Cumulative Fail Counter (Write not permitted) 715-825 Platen AGC Channel 2 Fail Count Since Reset0 0~65535 Cumulative Fail Counter at the previous clearing (Write not permitted) 715-826 Platen AGC Channel 3 Fail Count Overall Total0 0~65535 Cumulative Fail Counter (Write not permitted) 715-827 Platen AGC Channel 3 Fail Count Since Reset0 0~65535 Cumulative Fail Counter at the previous clearing (Write not permitted) 715-828 Platen AGC Channel 4 Fail Count Overall Total0 0~65535 Cumulative Fail Counter (Write not permitted) 715-829 Platen AGC Channel 4 Fail Count Since Reset0 0~65535 Cumulative Fail Counter at the previous clearing (Write not permitted) 715-830 Platen AGC Channel 5 Fail Count Overall Total0 0~65535 Cumulative Fail Counter (Write not permitted) 715-831 Platen AGC Channel 5 Fail Count Since Reset0 0~65535 Cumulative Fail Counter at the previous clearing (Write not permitted) 715-832 Platen AGC Channel 6 Fail Count Overall Total0 0~65535 Cumulative Fail Counter (Write not permitted) 715-833 Platen AGC Channel 6 Fail Count Since Reset0 0~65535 Cumulative Fail Counter at the previous clearing (Write not permitted) 715-834 Platen AOC Channel 1 Fail Count Overall Total0 0~65535 Cumulative Fail Counter (Write not permitted) 715-835 Platen AOC Channel 1 Fail Count Since Reset0 0~65535 Cumulative Fail Counter at the previous clearing (Write not permitted) 715-836 Platen AOC Channel 2 Fail Count Overall Total0 0~65535 Cumulative Fail Counter (Write not permitted) 715-837 Platen AOC Channel 2 Fail Count Since Reset0 0~65535 Cumulative Fail Counter at the previous clearing (Write not permitted)Table 3 Chain 715 Chain-Link Name Default Range Description
6/02 6-20DC1632/2240 Prelaunch Training/Review General Procedures and Information 719--xxx IIT/DADF Software NVM List715-838 Platen AOC Channel 3 Fail Count Overall Total0 0~65535 Cumulative Fail Counter (Write not permitted) 715-839 Platen AOC Channel 3 Fail Count Since Reset0 0~65535 Cumulative Fail Counter at the previous clearing (Write not permitted) 715-840 Platen AOC Channel 4 Fail Count Overall Total0 0~65535 Cumulative Fail Counter (Write not permitted) 715-841 Platen AOC Channel 4 Fail Count Since Reset0 0~65535 Cumulative Fail Counter at the previous clearing (Write not permitted) 715-842 Platen AOC Channel 5 Fail Count Overall Total0 0~65535 Cumulative Fail Counter (Write not permitted) 715-843 Platen AOC Channel 5 Fail Count Since Reset0 0~65535 Cumulative Fail Counter at the previous clearing (Write not permitted) 715-844 Platen AOC Channel 6 Fail Count Overall Total0 0~65535 Cumulative Fail Counter (Write not permitted) 715-845 Platen AOC Channel 6 Fail Count Since Reset0 0~65535 Cumulative Fail Counter at the previous clearing (Write not permitted) 715-854 Original Size Sensor Failure Total Count0 0~65535 Cumulative Fail Counter (Write not permitted) 715-855 Original Size Sensor Failures Since Reset0 0~65535 Cumulative Fail Counter at the previous clearing (Write not permitted) 715-856 IIT Memory Hot Line Failure Total Count0 0~65535 Cumulative Fail Counter (Write not permitted) 715-857 IIT Memory Hot Line Failures Since Reset0 0~65535 Cumulative Fail Counter at the previous clearing (Write not permitted) 715-858 DADF RAM CHECK Failure Total Count0 0~65535 Cumulative Fail Counter (Write not permitted) 715-859 DADF RAM CHECK Failures Since Reset0 0~65535 Cumulative Fail Counter at the previous clearing (Write not permitted) 715-900 Scan Life Count (upper digits) 36 0~65535 Scan Count Replacement Life (Upper Level) (Write not permitted) 715-901 Scan Life Count (lower digits) 40704 0~65535 Scan Count Replacement Life (Lower Level) (Write not permitted) Table 3 Chain 715 Chain-Link Name Default Range Description Table 4 Chain 719 Chain-Link Name Default Range Description 719-001 Version No. (Upper level) 0 0~65535 Indicates the IISS Version No. 719-002 Market Information 0 0~3 FX=0, AP=1, XC=2, XE=3 719-003 A4/Letter 1 0~3 Basic unit of document size. For A4 = bit0=1, letter = bit=1 *Checking of range is not performed. 719-004 ADF Version No. 0 0~65535 Indicates the ADF Version No. 719-005 IISS Major Version 0 0~65535 IISS Major Version No. 719-006 IISS Minor Version 0 0~65535 IISS Minor Version No. 719-007 IISS Revision Version 0 0~65535 IISS Revision Version No. 719-008 IISS Patch Version 0 0~65535 IISS Patch Version No.
6/02 6-21 DC1632/2240General Procedures and Information Prelaunch Training/Review 720-xxx ESS Meter/Counter NVM List 740--xxx IOT Manager NVM List 719-010 ADF Major Version 0 0~65535 ADF Major Version No. 719-011 ADF Minor Version 0 0~65535 ADF Minor Version No. 719-012 ADF Revision Version 0 0~65535 ADF Revision Version No. 719-013 ADF Patch Version 0 0~65535 ADF Patch Version No.Table 4 Chain 719 Chain-Link Name Default Range Description Table 5 Chain 720 Chain-Link Name Default Range Description 720-002 Billing PFV BILL- ING TYPE11~6 1 = Billing1, 2 = Billing2, 3 = Billing3, 4 = Billing4, 5 = Billing5, 6 = Billing6 720-003 Master Print-Full Color - 0~1999999 0~1,999,999 720-004 Master Print-Color1 - 0~1999999 0~1,999,999 720-005 Master Print-Color2 - 0~1999999 0~1,999,999 720-006 Master Print-B&W - 0~1999999 0~1,999,999 720-012 Backup1 Print-Full Color - 0~1999999 0~1,999,999 720-013 Backup1 Print-Color1 - 0~1999999 0~1,999,999 720-014 Backup1 Print-Color2 - 0~1999999 0~1,999,999 720-015 Backup1 Print-B&W - 0~1999999 0~1,999,999 720-040 [PSW Display] Group 0 0~999999999 9990~999999999999 (0 means not set up) 720-041 TBD 0 0~999999999 9990~999999999999 (0 means not set up) 720-042 TBD 0 0~3 0 = FreeAccess, 1 = Color Only, 2 = B&W Only, 3 = Cannot be used 720-043 TBD 0 0~3 0 = FreeAccess, 1 = Color Only, 2 = B&W Only, 3 = Cannot be used 720-044 Group C Mode to use 0 0~3 0 = FreeAccess, 1 = Color Only, 2 = B&W Only, 3 = Cannot be usedTable 6 Chain 740 Chain-Link Name Default Range Description 740-024 RegiCon Request Flag 0 0~255 0 = Performed, 1 = Not performed 740-025 Edge Check Request Flag 0 0~255 0 = Performed, 1 = Not performed 740-026 ProCon Request Flag 0 0~255 0 = Performed, 1 = Not performed
6/02 6-22DC1632/2240 Prelaunch Training/Review General Procedures and Information 741--xxx Drive NVM List 742--xxx Paper Handling NVM List Table 7 Chain 741 Chain-Link Name Default Range Description 741-054 NVM_PR_MOT_HIGH_PULSE (PR (Drum) Motor Speed Fine Adjustment (Standard)23 0~40 Performs fine adjustment of Drum Speed at Standard Speed. Increases the Drum Speed by +1 (approx. 0.05%) with respect to the initial value. Decreases the Drum Speed by -1 (approx. 0.05%). 741-055 NVM_PR_MOT_LOW_PULSE (PR (Drum) Motor Speed Fine Adjustment (Heavy Weight /Transparency)23 0~40 Fine adjusts the Drum Speed at half speed. Increases the Drum Speed by +1 (approx. 0.05%) with respect to the initial value. Decreases the Drum Speed by -1 (approx. 0.05%). 741-056 Belt Home Fail Too Long Counter 0 0~3 It is necessary to reset the No. of Occurrence of Belt Home Fail Too Long to 3. 741-057 NoPaperRun Mode SW 0 0~2 0 = Normal NoPaperRun 1 = MainMotor Stop 2 = Main/Dev. Motor Stop 741-068 NVM_PR_MOT_DOUBLE_PULSE (PR (Drum) Motor Speed Fine Adjustment (Double Speed)22 0~40 Fine adjusts the Drum Speed at double speed. Increases the Drum Speed by +1 (approx. 0.05%) with respect to the initial value. Decreases the Drum Speed by -1 (approx. 0.05%).Table 8 Chain 742 Chain-Link Name Default Range Description 742-001 Invert Clutch CW Off Timing 82 0~163 (1bit= 2.4462ms)Paper inversion position adjustment (P Speed) default=2300ms 742-002 Invert Clutch CW Off Timing (MF-1) 106 0~259 (1bit= 1.31136ms)Paper inversion position adjustment (Double Speed) 742-006 RegiLoopLengthAjust (Tray Standard Paper)41 0~81 (1bit= 2.4462ms)Regi Loop Length Adjustment (P Speed) for Standard Paper from Tray. Default=260ms 742-007 RegiLoopLengthAjust (Tray Standard Paper) (MF)41 0~81 (1bit= 1.31136ms)Regi Loop Length Adjustment (Double Speed) for Standard Paper from Tray 742-009 RegiLoopLengthAjust (Tray 5 Standard Paper)41 0~81 Regi Loop Length Adjustment (P Speed) for Standard Paper from Tray 5 (1bit= 2.4462ms) 742-011 RegiLoopLengthAjust (Tray 5 Standard Paper) (MF)41 0~81 (1bit= 1.322ms)Regi Loop Length Adjustment (Double Speed) for Standard Paper from MSI 742-013 RegiLoopLengthAjust (Tray 5 Heavy2 Paper)41 0~81 (1bit= 4.8924ms)Regi Loop Length Adjustment (Half Speed) for Heavy Weight Paper from MSI. Default=221ms 742-014 RegiLoopLengthAjust (DUP) (2sheets of paper)41 0~81 (1bit= 2.4462ms)Regi Loop Length Adjustment (P Speed) from Dup (Feeding length Letter-LEF and Shorter) Default=157ms 742-015 RegiLoopLengthAjust (DUP) (MF) 76 0~152 (1bit= 1.31136ms)Regi Loop Length Adjustment (Double Speed) from Dup 742-016 T/A Clutch On Timing (From Regi Start) 20 8~32 (1bit= 2.4462ms)Synchronize adjustment to be same as Regi Clutch at Regi Start (-30~30ms) Default=0ms 742-017 Dup On Timing (From Regi Start) 20 0~40 (1bit= 2.4462ms)Synchronize adjustment to be same as Regi Clutch at Regi Start (P Speed). Default=373ms 742-018 Full Stack Paper Sensing Condition 2 1~12 (1bit= 5sec) Full Stack Detection Condition (5~60sec). 742-019 Full Stack Paper Cancel Condition 1 1~30 (1bit= 1sec) Full Stack Cancel Condition (1~30sec) 742-020 Feed Start Timing (MSI) 41 0~82 (1bit= 2.4462ms)Feed Start Timing Adjustment from Pitch (P Speed) (850~1050ms). Default=950ms
6/02 6-23 DC1632/2240General Procedures and Information Prelaunch Training/Review 742-021 Feed Start Timing (MSI) (MF) 150 0~300 (1bit= 1.31136ms)Feed Start Timing Adjustment from Pitch (Double Speed) (100~500ms) 742-022 Feed Motor Off Timing 10 0~35 (1bit= 10ms)Feed Motor Off Timing Adjustment from T/A Nip 742-023 Regi Clutch Off Timing 41 0~81 (1bit= 2.4462ms)Adjusts the time between the paper rear edge has passes the Regi Sensor and the Regi Clutch Turns Off (P Speed) (90~290ms). Default=190ms 742-024 Regi Clutch Off Timing (MF) 76 0~152 (1bit= 1.31136ms)Adjusts the time between the paper rear edge has passes the Regi Sensor and the Regi Clutch Turns Off (Dou- ble Speed) 742-025 ADJUST SIDE REGI (ALL) 25 0~50 (1bit= 0.211mm)Side Regi Adjustment (ALL, Offset value) 742-026 ADJUST SIDE REGI (MSI) 20 0~50 (1bit= 0.211mm)Side Regi Adjustment (MSI) 742-027 ADJUST SIDE REGI (Dup) 22 0~50 (1bit= 0.211mm)Side Regi Adjustment (Dup) 742-028 ADJUST LEAD REGI (ALL) 20 0~40 (1bit= 0.2544mm)Lead Regi Adjustment (ALL, Offset value) 742-029 ADJUST LEAD REGI (Tray) 12 0~40 (1bit= 0.2544mm)Lead Regi Adjustment (P Speed) from Tray 742-030 ADJUST LEAD REGI (Tray) 20 0~40 (1bit= 0.2544mm)Lead Regi Adjustment (Double Speed) from Tray 742-031 ADJUST LEAD REGI (MSI) (Standard Paper)11 0 ~4 0 (1bit= 0.2544mm)Lead Regi Adjustment (P Speed) Standard Paper from Tray 5 742-032 ADJUST LEAD REGI (MSI) (Standard Paper)20 0~40 (1bit= 0.2544mm)Lead Regi Adjustment (Double Speed) Standard Paper from MSI 742-033 ADJUST LEAD REGI (MSI) (Heavy1) 20 0~40 (1bit= 0.2544mm)Lead Regi Adjustment (P Speed) Heavy Weight Paper 1 from Tray 5 742-034 ADJUST LEAD REGI (MSI) (Heavy2) 20 0~40 (1bit= 0.2544mm)Lead Regi Adjustment (Half Speed) Heavy Weight Paper 2 from Tray 5 742-035 ADJUST LEAD REGI (MSI) (Heavy Paper1)20 0~40 (1bit= 0.2544mm)Lead Regi Adjustment (Half Speed) Heavy Weight Paper 1 from Tray 5 742-036 ADJUST LEAD REGI (MSI) (Heavy Paper2)20 0~40 (1bit= 0.2544mm)Lead Regi Adjustment (Half Speed) Heavy Weight Paper 2 from Tray 5 742-037 ADJUST LEAD REGI (Dup) 11 0~40 (1bit= 0.2544mm)Lead Regi Adjustment (P Speed) (Side2) 742-038 ADJUST LEAD REGI (Dup) 20 0~40 (1bit= 0.2544mm)Lead Regi Adjustment (Double Speed) (Side2) 742-039 Jam Bypass 0 0~255 0 = Normal Mode 255 = Jam Bypass 742-040 OCT Start Timing (Offset) 42 0~202 (1bit= 2.4462ms)OCT (Offset) Start Timing Adjustment (P Speed) 742-041 OCT Start Timing (Offset) 42 0~202 (1bit= 1.31136ms)OCT (Offset) Start Timing Adjustment (Double Speed) 742-046 Face Up Tray Condition 0 0~1 Face Up Tray Present 0 = No 1 = Yes 742-047 OCT Start Timing (Home) 17 0~112 (1bit= 2.4462ms)OCT (Home) Start Timing Adjustment (P Speed)Table 8 Chain 742 Chain-Link Name Default Range Description
6/02 6-24DC1632/2240 Prelaunch Training/Review General Procedures and Information742-048 OHP Sheet Sensing Condition 1 0~1 Transparency Detection 1 = Detect 0 = Does not detect 742-049 Tray 5 Side Guide Min Data 972 927~1017 (1bit= 1mm)Saves the Tray 5 Size Detection Min Value 742-050 Tray 5 Side Guide Max Data 52 7~97 (1bit= 1mm) Saves the Tray 5 Size Detection Max Value 742-051 FEED START TIMING 1Tray 82 (450ms)0~163 (1bit= 2.4462ms)Adjusts the time between Pitch (Standard Signal IOT) and FEED Starts (250~650ms). 742-052 FEED START TIMING 1Tray 82 0~163 (1bit= 1.31136ms) 742-053 ADJUST SIDE REGI 1Tray 22 0~50 (1bit= 0.211mm)SIDE REGI Adjustment for each TRAY 742-054 PAPER THE REST 1Tray 0 0~4000 Saves the Cumulative LIFT UP Time from TRAY insertion (For remaining detection calculation as=A). 742-055 PRE T/A START TIMING 3TM-1 74 0~115 (1bit= 2.4462ms)Adjusts the Time between PRE T/A Starts and Standard Signal (IOT) (303~803ms) 742-056 PRE T/A START TIMING 3TM-2 74 0~115 (1bit= 2.4462ms)Adjusts the Time between PRE T/A Starts and Standard Signal (IOT) (365~865ms) 742-057 PRE T/A START TIMING 3TM-3 74 0~115 (1bit= 2.4462ms)Adjusts the Time between PRE T/A Starts and Standard Signal (IOT) (429~929ms) 742-058 PRE T/A START TIMING TTM-1 10 0~16 (1bit= 2.4462ms)Adjusts the Time between PRE T/A Starts and Standard Signal (IOT) 742-059 PRE T/A START TIMING TTM-2 74 0~115 (1bit= 2.4462ms)Adjusts the Time between PRE T/A Starts and Standard Signal (IOT) (457~957ms) 742-060 PRE T/A START TIMING TTM-3 74 0~115 (1bit= 2.4462ms)Adjusts the Time between PRE T/A Starts and Standard Signal (IOT) (431~931ms) 742-061 PRE T/A START TIMING 1TM-1 102 0~204 (1bit= 2.4462ms)Adjusts the Time between PRE T/A Starts and Standard Signal (IOT) (303~803ms). Default=553ms 742-062 ADJUST PRE FEED POSITION 3TM-1 0 0~40 (1bit= 10ms)Adjust the Time between the FEED OUT SNR ON and the FEED MOT OFF (0~400ms). 742-063 ADJUST PRE FEED POSITION 3TM-2 0 0~40 (1bit= 10ms)Adjust the Time between the FEED OUT SNR ON and the FEED MOT OFF (0~400ms). 742-064 ADJUST PRE FEED POSITION 3TM-3 0 0~40 (1bit= 10ms)Adjust the Time between the FEED OUT SNR ON and the FEED MOT OFF (0~400ms). 742-065 ADJUST PRE FEED POSITION TTM-1 0 0~40 (1bit= 10ms)Adjust the Time between the FEED OUT SNR ON and the FEED MOT OFF (0~400ms). 742-066 ADJUST PRE FEED POSITION TTM-2 0 0~40 (1bit= 10ms)Adjust the Time between the FEED OUT SNR ON and the FEED MOT OFF (0~400ms). 742-067 ADJUST PRE FEED POSITION TTM-3 37 10~50 (1bit= 10ms)Adjust the Time between the FEED OUT SNR ON and the FEED MOT OFF (100~500ms). Default=370ms 742-068 ADJUST PRE FEED POSITION 1TM-1 0 0~40 (1bit= 10ms)Adjust the Time between the FEED OUT SNR ON and the FEED MOT OFF (0~400ms). 742-069 MAIN FEED START TIMING 3TM-1 20 0~44 (1bit= 10ms)Adjust the Time between the MAIN FEED Starts and the PRE T/A (330~830ms). 742-070 MAIN FEED START TIMING 3TM-2 20 0~44 (1bit= 10ms)Adjust the Time between the MAIN FEED Starts and the PRE T/A (570~1070ms).Table 8 Chain 742 Chain-Link Name Default Range Description
6/02 6-25 DC1632/2240General Procedures and Information Prelaunch Training/Review 742-071 MAIN FEED START TIMING 3TM-3 20 0~44 (1bit= 10ms)Adjust the Time between the MAIN FEED Starts and the PRE T/A (810~1310ms). 742-072 MAIN FEED START TIMING TTM-1 20 0~44 (1bit= 10ms)Adjust the Time between the MAIN FEED Starts and the PRE T/A (330~830ms). 742-073 MAIN FEED START TIMING TTM-2 20 0~44 (1bit= 10ms)Adjust the Time between the MAIN FEED Starts and the PRE T/A (780~1280ms). 742-074 MAIN FEED START TIMING TTM-3 20 0~44 (1bit= 10ms)Adjust the Time between the MAIN FEED Starts and the PRE T/A (1410~1910ms). 742-075 MAIN FEED START TIMING 1TM-1 25 0~50 (1bit= 10ms)Adjust the Time between the MAIN FEED Starts and the PRE T/A (330~830ms).Default=580ms 742-076 ADJUST SIDE REGI 2Tray 20 0~50 (1bit= 0.211mm)SIDE REGI adjustment of 2TRAY 742-077 ADJUST SIDE REGI 3Tray 20 0~50 (1bit= 0.211mm)SIDE REGI adjustment of 3TRAY 742-078 ADJUST SIDE REGI 4Tray 20 0~50 (1bit= 0.211mm)SIDE REGI adjustment of 4TRAY 742-079 ADJUST SIDE REGI TrayModuleAll 25 0~50 (1bit= 0.211mm)SIDE REGI adjustment of 2, 3, 4TRAY (Batch adjustment) 742-080 PAPER THE REST 3TM-1 0 0~4000 Saves the Cumulative LIFT UP Time from TRAY insertion (For remaining detection calculation as=A). 742-081 PAPER THE REST 3TM-2 0 0~4000 Saves the Cumulative LIFT UP Time from TRAY insertion (For remaining detection calculation as=A). 742-082 PAPER THE REST 3TM-3 0 0~4000 Saves the Cumulative LIFT UP Time from TRAY insertion (For remaining detection calculation as=A). 742-083 PAPER THE REST TTM-1 0 0~4000 Saves the Cumulative LIFT UP Time from TRAY insertion (For remaining detection calculation as=A). 742-084 PAPER THE REST TTM-2 0 0~12000 Saves the Cumulative LIFT UP Time from TRAY insertion (For remaining detection calculation as=A). 742-085 PAPER THE REST TTM-3 0 0~15000 Saves the Cumulative LIFT UP Time from TRAY insertion (For remaining detection calculation as=A). 742-086 PAPER THE REST 1TM-1 0 0~4000 Saves the Cumulative LIFT UP Time from TRAY insertion (For remaining detection calculation as=A). 742-087 OCT Condition 1 0~1 0 = Not available, 1 = Available 742-088 Dup On Timing (From Regi Start) 20 0~40 (1bit= 1.31136ms)Synchronize adjustment to be same as the Regi Clutch at Regi Start (Double Speed) 742-089 OCT Start Timing (Home) 17 0~112 (1bit= 1.31136ms)OCT (Home) Start Timing Adjustment (Double Speed) 742-093 PRE T/A START TIMING 3TM-1 139 0~215 (1bit= 1.31136ms)Adjusts the Time between PRE T/A Starts and Standard Signal (IOT) (303~803ms) 742-094 PRE T/A START TIMING 3TM-2 139 0~215 (1bit= 1.31136ms)Adjusts the Time between PRE T/A Starts and Standard Signal (IOT) (365~865ms) 742-095 PRE T/A START TIMING 3TM-3 139 0~215 (1bit= 1.31136ms)Adjusts the Time between PRE T/A Starts and Standard Signal (IOT) (429~929ms) 742-096 PRE T/A START TIMING TTM-2 139 0~215 (1bit= 1.31136ms)Adjusts the Time between PRE T/A Starts and Standard Signal (IOT) (457~957ms) 742-097 PRE T/A START TIMING TTM-3 139 0~215 (1bit= 1.31136ms)Adjusts the Time between PRE T/A Starts and Standard Signal (IOT) (431~931ms) 742-098 MAIN FEED START TIMING 3TM-1 38 0~83 (1bit= 1.31136ms)Adjust the Time between the MAIN FEED Starts and the PRE T/A (330~830ms). 742-099 MAIN FEED START TIMING 3TM-2 38 0~83 (1bit= 1.31136ms)Adjust the Time between the MAIN FEED Starts and the PRE T/A (570~1070ms).Table 8 Chain 742 Chain-Link Name Default Range Description
6/02 6-26DC1632/2240 Prelaunch Training/Review General Procedures and Information 744--xxx User NVM List742-100 MAIN FEED START TIMING 3TM-3 38 0~83 (1bit= 1.31136ms)Adjust the Time between the MAIN FEED Starts and the PRE T/A (810~1310ms). 742-101 MAIN FEED START TIMING TTM-2 38 0~83 (1bit= 1.31136ms)Adjust the Time between the MAIN FEED Starts and the PRE T/A (780~1280ms). 742-102 MAIN FEED START TIMING TTM-3 38 0~83 (1bit= 1.31136ms)Adjust the Time between the MAIN FEED Starts and the PRE T/A (1410~1910ms). 742-103 Select A/B or INCH (SMH Auto Detect) 0 0~1 0 = A/B series, 1 = Inch series 742-104 Select 2ndBTR Cleaning (SMH Auto Detect)1 0~1 0 = No, 1 = Yes 742-105 RegiLoopLengthAjust (DUP) (a sheet of paper)41 0~81 (1bit= 2.4462ms)Lead Regi Length Adjustment (P Speed) from Dup (Feeding Length Letter-LEF and longer)Default=157ms 742-106 PRE T/A START TIMING 3TM-1 (Half) 37 0~58 (1bit= 4.8924ms)Adjusts the Time between PRE T/A Starts and Standard Signal (IOT) (303~803ms) 742-107 PRE T/A START TIMING 3TM-2 (Half) 37 0~58 (1bit= 4.8924ms)Adjusts the Time between PRE T/A Starts and Standard Signal (IOT) (365~865ms) 742-108 PRE T/A START TIMING 3TM-3 (Half) 37 0~58 (1bit= 4.8924ms)Adjusts the Time between PRE T/A Starts and Standard Signal (IOT) (429~929ms) 742-109 PRE T/A START TIMING TTM-2 (Half) 37 0~58 (1bit= 4.8924ms)Adjusts the Time between PRE T/A Starts and Standard Signal (IOT) (457~957ms) 742-110 PRE T/A START TIMING TTM-3 (Half) 37 0~58 (1bit= 4.8924ms)Adjusts the Time between PRE T/A Starts and Standard Signal (IOT) (431~931ms) 742-111 MAIN FEED START TIMING 3TM-1 (Half)10 0~22 (1bit= 4.8924ms)Adjust the Time between the MAIN FEED Starts and the PRE T/A (330~830ms). 742-112 MAIN FEED START TIMING 3TM-2 (Half)10 0~22 (1bit= 4.8924ms)Adjust the Time between the MAIN FEED Starts and the PRE T/A (570~1070ms). 742-113 MAIN FEED START TIMING 3TM-3 (Half)10 0~22 (1bit= 4.8924ms)Adjust the Time between the MAIN FEED Starts and the PRE T/A (810~1310ms). 742-114 MAIN FEED START TIMING TTM-2 (Half)10 0~22 (1bit= 4.8924ms)Adjust the Time between the MAIN FEED Starts and the PRE T/A (780~1280ms). 742-115 MAIN FEED START TIMING TTM-3 (Half)10 0~22 (1bit= 4.8924ms)Adjust the Time between the MAIN FEED Starts and the PRE T/A (1410~1910ms).Table 8 Chain 742 Chain-Link Name Default Range Description Table 9 Chain 744 Chain-Link Name Default Range Description 744-001 STS-1 CONT TEMP in Low PWR Mode 80 0~160 (1 bit=1 deg. C)Main-Lamp temperature control in Low-Power Mode. Setting the default as 0 Degrees Celsius is same as Fuser-Off. It is necessary for high temperature for recovery Time Claim. 744-002 STS-2 CONT TEMP in Low PWR Mode 80 0~160 (1 bit=1 deg. C)Sub-Lamp temperature control in Low-Power Mode. Setting the default as 0 Degrees Celsius is same as Fuser- Off. It is necessary for high temperature for recovery Time Claim. 744-003 UM status by High Temperature Error Detection0 0~2 0 (Normal) or 1 (STS-1 High Temperature Error Detection) or 2 (STS-2 High Temperature Error Detection).UM Status occurs when either STS-1 or STS-2 High Temperature Error Detection is detected. Once this occurs, UM cannot be canceled unless this NVM value is changed to 0 by entering the Diag Mode in the Interlock-Open sta- tus of the M/C-Front Cover.