Toshiba Estudio 230 Manual

							June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 115
2
638 General Time differences ALL EUR: 24 UC: 40JPN: 6
 SYS 0: +12.0h 1: +11.5h
2: +11.0h 3: +10.5h 
4: +10.0h 5: +9.5h 
6: +9.0h 7: +8.5h
8: +8.0h 9: +7.5h 
10: +7.0h 11: +6.5h 
12: +6.0h 13: +5.5h
14: +5.0h 15: +4.5h 
16: +4.0h 17: +3.5h 
18: +3.0h 19: +2.5h 
20: +2.0h 21: +1.5h 
22: +1.0h 23: +0.5h 
24: 0.0h 25: -0.5h 
26: -1.0h 27: -1.5h 
28: -2.0h 29: -2.5h 
30: -3.0h 31: -3.5h
32: -4.0h 33: -4.5h 
34: -5.0h 35: -5.5h 
36: -6.0h 37: -6.5h
38: -7.0h 39: -7.5h 
40: -8.0h 41: -8.5h 
42: -9.0h 43: -9.5h
44: -10.0h
45: -10.5h 
46: -11.0h 
47: -11.5h 1
640 User  interface Date display format ALL EUR: 1
UC: 2
JPN: 0
 SYS 0: YYYY.MM.DD.
1: DD.MM.YYYY 
2: MM.DD.YYYY 1
641 User  interface Automatic Sorting Mode  
setting (RADF) PPC 2
 SYS 0: Invalid 1: STAPLE
2: SORT 3: GROUP 
4: ROTATE SORT 1
642 User  interface Default setting of Sorter  
Mode PPC 0
 SYS 0: NON-SORT
1: STAPLE 
2: SORT 3: GROUP 
4: ROTATE SORT 1
645 User  interface Correction of reproduction  
ratio in editing copy PPC 10
 SYS Sets the reproduction 
ratio for the “X in 1” 
printing (including mag- 
azine sort) to the  
“Reproduction ratio x  
Correction ratio”. 
0: 90% 1: 91% 
2: 92% 3: 93%
4: 94% 5: 95% 
6: 96% 7: 97% 
8: 98% 9: 99%
10: 100% 1
646 User  interface Image position in editing PPC 0
SYS Sets the page pasted 
position for “X in 1” to  
the upper left corner/ 
center. 
0: Cornering 
1: Centering 1
647 User  interface Rotation of paper direction  
for BOX printing ALL 1
 SYS 0: Rotation OFF
1: Rotation ON 1
Setting mode (08) 
Code Classifi-
cation ItemsFunc-
tion Default
 RAM Contents
Proce-
dure
05/11 
						

							e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 116
648 User 
interface Returning finisher tray  
when printing is finished ALL 0
 SYS Sets whether or not 
returning the finisher  
tray to the bin 1 when  
printing is finished.
0: Not returned 
1: Returned 1
649 User  interface Magazine sort setting PPC 0
SYS 0: Left page to right 
page
1: Right page to left  page 1
650 User  interface 2 in 1/4 in 1 page allocating  
order setting PPC 0
 SYS 0: Horizontal
1: Vertical 1
651 User  interface Printing format setting for 
Time stamp and Page  
Number PPC 2
 SYS Hyphen 
(with page number)
/Dropout 
 (with date, time and 
page number) 
0: OFF/OFF 
1: ON/OFF
2: OFF/ON 
3: ON/ON
Note: Note: Hyphen printing  
format 
ON: -1-  OFF: 1 1
652 User  interface Cascade operation setting PPC 0
SYS 0: OFF 1: ON 1
653 User  interface Cascade operation setting PRT 0
SYS 0: OFF   1: ON 1
657 User  interface Direction priority for date 
and time stamp printing PPC 0
 SYS 0: Short edge
1: Long edge 1
658 User  interface Auto Job Start setting for 
bypass feed printing PRT 0
 SYS Sets whether or not 
feeding a paper auto- 
matically into the equip- 
ment when it is placed 
on the bypass tray. 
0: OFF (Press the 
[START] button to  
start feeding.)
1: ON (Automatic 
feeding) 1
659 User  interface Auto Job start setting for  
bypass feed printing PPC 1
 SYS Sets whether or not 
feeding a paper auto- 
matically into the equip- 
ment when it is placed 
on the bypass tray. 
0: OFF (Press the [START] button to  
start feeding.)
1: ON (Automatic 
feeding) 1
660 Network Auto-forwarding setting of  received FAX ALL 0
 SYS 0: Invalid
1: Valid 1
661 Network Auto-forwarding setting of  received E-mail ALL 0
 SYS 0: Invalid
1: Valid 1
Setting mode (08) 
Code Classifi-
cation ItemsFunc-
tion Default
 RAM Contents
Proce-
dure
04/09 
						

							June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 117
2
662 General Clearing of SMS partition ALL - SYS Clears SM S partition.
(Performs when the  
service call [F106] has  
occurred.) 3
666 General /SHR partition clearing ALL - SYS Initializes  the Elec-
tronic Filing. 3
667 General /SHA partition clearing ALL - SYS Initializes  the shared 
folder. 3
670 General HDD diagnostic menu dis- play ALL - SYS Display the HDD infor-
mation 2
671 User  interface Size indicator ALL 0
SYS 0: Invalid
1: Valid 1
672 General Initialization of department  management information - - SYS Initializing of the depart-
ment management 
information
* Key in the code and 
press the [INITIAL-
IZE] button to per-
form the  
initialization. If the  
area storing the 
department man- 
agement informa- 
tion is destroyed for  
some reason, “Enter  
Department Code”  
is displayed on the  
control panel even if  
the department  
management func- 
tion is not set on. In 
this case, initialize  
the area with this  
code. This area is  
normally initialized  
at the factory. 3
673 General Trial period setting PRT/ SCN254
 SYS Sets the trial period 
from 1 to 60 days. This  
setting is effective only  
when the default value  
is “254”. Once the 
default value is set, this  
value is only used for a  
reference. 1
678 General Setting of banner advertis- ing display ALL 0
 SYS Sets whether or not dis-
playing the banner  
advertising. The setting  
contents of 08-679 and  
08-680 are displayed at  
the time display section  
on the right top of the  
screen. When both are  
set, each content is dis- 
played alternately.
0: Not displayed 
1: Displayed 1
679 General Banner advertising display  1 ALL - SYS Maximum 27 letters 
(one-byte character) 11
Setting mode (08) 
Code Classifi-
cation Items
Func-
tion Default
 RAM Contents
Proce-
dure 
						

							e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 118
680 General Banner advertising display 
2 ALL - SYS Maximum 27 letters 
(one-byte character) 11
681 General Display of [BANNER MES- SAGE] button  ALL 0
 SYS 0: Not displayed
1: Displayed 
* This button enables 
the entry of “Banner  
advertising display 1  
(08-679)” and “Ban- 
ner advertising dis- 
play 2 (08-680)” on  
the control panel. 1
682 User  interface Offsetting between jobs ALL 0
SYS 0: Invalid
1: Valid 1
683 General Duplex printing setting  when coin controller is 
used ALL 1
 SYS When the duplex print-
ing is short paid with a 
coin controller, reverse 
side of the original is  
not printed and is con- 
sidered as a defect 
(printing job may be  
cleared). To solve this  
problem, the selection 
of printing method is 
enabled with this set- 
ting. 
0: Invalid (Both sides 
printed)
1: Valid (Only one side 
printed) 1
684 General Rebuilding all databases ALL - SYS Rebuilds a ll databases. 3
685 General Rebuilding all databases  related to address book ALL - SYS Rebuilds all databases 
related to the Address  
Book. 3
686 General Rebuilding all databases  related to log ALL - SYS Rebuilds all databases 
related to the log. 3
689 FAX Adaptation of paper source  priority selection FAX 0
 SYS 0: Not subjected for 
APS judgment
1: Subjected for APS 
judgment 1
690 General HDD formatting ALL - SYS 2: Normal formatting 7
691 General HDD type display ALL - SYS 0: Not formatted
1: Not used 
2: Normal format 7
692 Mainte- nance Performing panel calibra- 
tion ALL - SYS Performs the calibration 
of the pressing position  
on the touch panel  
(LCD screen). The cali-
bration is performed by  
pressing 2 reference  
positions after this code 
is started up. 1
693 General Initialization of NIC infor- mation ALL - SYS Returns the value to the 
factory shipping default  
value. 3
694 General Performing HDD testing ALL - SYS Checks the b ad sector. 3
Setting mode (08) 
Code Classifi-
cation Items
Func-
tion Default
 RAM Contents
Proce-
dure 
						

							June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 119
2
695 General Notifying condition of trial  period end PRT/
SCN 3
 SYS Sets when the end of 
trial period is notified. 
0: On the day it ends 
1 to 59: n days before 1
696 Scram- bler 
board Installation of scrambler  
board (Option)
ALL 0
 - 0: Not installed
1: Installed 2
697 Paper  feeding Paper type priority PPC 1
SYS Sets the paper type pri-
ority during copying. 
1: Plain paper 
2: Thick paper 1 1
698 Scram- bler 
board Entering the key code for  
scrambler board
ALL - - Start up this code and 
have the user enter the 
key code. 
Once the key code has  
been set, this code can-
not be set again on  
security grounds. 5
699 Scram- bler 
board Erasing all data in HDD ALL - - This setting is effectiv
e 
only when the scram- 
bler board is installed. 3
701 FAX Destination setting for FAX FAX EUR: 5 UC: 4
JPN: 0
Other: 1
 SYS 0: Japan 1: Asia
2: Australia 
3: Hong Kong 
4: U.S.A./Canada
5: Germany 6: U.K. 
7: Italy 
8: Belgium
9: Netherlands 
10: Finland 
11: Spain
12: Austria 
13: Switzerland 
14: Sweden
15: Denmark 
16: Norway 
17: Portugal
18: France 
19: Greece 
20: Poland
21: Hungary 
22: Czech 
23: Turkey 
24: South Africa 
25: Taiwan 1
702 Mainte- nance Remote-controlled service  
function ALL 2
 SYS 0: Valid (Remote-con-
trolled server)
1: Valid (L2) 
2: Invalid 1
703 Mainte- nance Remote-controlled service 
HTTP server
URL setting ALL - SYS Maximum 256 Bytes 11
Setting mode (08) 
Code Classifi-
cation ItemsFunc-
tion Default
 RAM Contents
Proce-
dure
04/09 
						

							e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 120
707 Mainte-
nance Remote-controlled service 
HTTP initially-registered  
server 
URL setting ALL https://
device. 
mfp- 
support.
com:443/ 
device/ 
firstregist.
ashx SYS Maximum 256 Bytes 11
710 Mainte- nance
(Remote) Short time interval setting  
of recovery from Emer- 
gency Mode ALL 24
 SYS Sets the time interval to 
recover from the Emer-
gency Mode to the Nor-
mal Mode. 
(Unit: Hour) 1
711 Mainte- nance
(Remote) Short time interval setting  
of Emergency Mode 
ALL 60
 SYS Unit: Minute 1
715 Mainte- nance Remote-controlled service  
periodical polling timing 
(Hour/Hour/Minute/Minute) ALL 1230 SYS 0 (0:00) to 2359 (23:59) 1
716 Mainte- nance Remote-controlled service 
Writing data of self-diag-
nostic code ALL 0
 SYS 0: Prohibited
1: Accepted 1
717 Mainte- nance Remote-controlled service  
response waiting time 
(Timeout) ALL 3
 SYS Unit: Minute 1
718 Mainte- nance Remote-controlled service 
initial registration ALL 0
 SYS 0: OFF
1: Start 
2: Only certification is 
scanned 1
719 Mainte- nance Remote-controlled service  
tentative password ALL - SYS Maximum 10 letters 11
720 Mainte- nance Status of remote-con- 
trolled service initial regis- 
tration 
(Display only) ALL 0
 SYS 0: Not registered
1: Registered 2
721 Mainte- nance Service center call function ALL 2
SYS 0: OFF
1: Notifies all service 
calls
2: Notifies all but  paper jams 1
723 Mainte- nance Service center call
HTTP server URL setting ALL - SYS Maximum 256 letters 11
726 Mainte- nance HTTP proxy setting ALL 1
SYS 0: Valid
1: Invalid 1
727 Mainte- nance HTTP proxy IP address  
setting ALL - SYS 000.000.000.000-
255.255.255.255 
(Default value 
000.000.000.000) 11
728 Mainte- nance HTTP proxy port number  
setting ALL 0
 SYS 1
729 Mainte- nance HTTP proxy ID setting ALL - SYS Maximum 30 letters 11
730 Mainte- nance HTTP proxy password set-
ting ALL - SYS Maximum 30 letters 11
731 Mainte- nance HTTP proxy panel display ALL 1
SYS 0: Valid
1: Invalid 1
Setting mode (08) 
Code Classifi-
cation ItemsFunc-
tion Default
 RAM Contents
Proce-
dure
04/09 
						

							June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 121
2
732 Mainte- nance 
(Remote) Automatic ordering func- 
tion of supplies
ALL 3
 SYS 0: Ordered by FAX
1: Ordered by E-mail 
2: Ordered by HTTP 
3: OFF 1
733 Mainte- nance 
(Remote) Automatic ordering func- 
tion of supplies 
FAX number ALL - SYS Maximum 32 digits
Enter hyphen with the 
[Monitor/Pause] button 11
734 Mainte- nance 
(Remote) Automatic ordering func- 
tion of supplies 
E-mail address ALL - SYS Maximum 192 letters
List: 256 digits 11
738 Mainte- nance 
(Remote) Automatic ordering func- 
tion of supplies 
Users name ALL - SYS Maximum 50 letters 11
739 Mainte- nance 
(Remote) Automatic ordering func-
tion of supplies 
Users telephone number ALL - SYS Maximum 32 digits
Enter hyphen with the 
[Monitor/Pause] button 11
740 Mainte- nance 
(Remote) Automatic ordering func- 
tion of supplies 
Users E-mail address ALL - SYS Maximum 192 letters
List: 256 digits 11
741 Mainte- nance 
(Remote) Automatic ordering func- 
tion of supplies 
Users address ALL - SYS Maximum 100 letters 11
742 Mainte- nance 
(Remote) Automatic ordering func- 
tion of supplies
Service number ALL 0
 SYS Maximum 5 digits 11
743 Mainte- nance 
(Remote) Automatic ordering func- 
tion of supplies 
Service technicians name ALL - SYS Maximum 50 letters 11
744 Mainte- nance 
(Remote) Automatic ordering func-
tion of supplies 
Service technicians tele- 
phone number ALL - SYS Maximum 32 digits
Enter hyphen with the  
[Monitor/Pause] button 11
745 Mainte- nance 
(Remote) Automatic ordering func- 
tion of supplies 
Service technicians E-mail  
address ALL - SYS Maximum 192 letters
List: 256 digits 11
746 Mainte- nance 
(Remote) Automatic ordering func- 
tion of supplies 
Suppliers name ALL - SYS Maximum 50 letters 11
747 Mainte- nance 
(Remote) Automatic ordering func- 
tion of supplies 
Suppliers address ALL - SYS Maximum 100 letters 11
748 Mainte- nance 
(Remote) Automatic ordering func- 
tion of supplies 
Notes ALL - SYS Maximum 128 letters 11
758 Mainte- nance 
(Remote) Information about supplies 
Part number of toner car- 
tridge ALL - SYS Maximum 20 digits 11
759 Mainte- nance
(Remote) Information about supplies 
Order quantity of toner car-
tridge ALL 1
 SYS 1
760 Mainte- nance
(Remote) Information about supplies 
Condition number of toner  
cartridge ALL 1
 SYS 1
764 Mainte- nance
(Remote) Automatic ordering sup- 
plies 
Result table printout ALL 1
 SYS 0: OFF
1: Always
2: ON Error 1
Setting mode (08) 
Code Classifi-
cation ItemsFunc-
tion Default
 RAM Contents
Proce-
dure
04/09 
						

							e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 122
765 Mainte-
nance
(Remote) Automatic ordering sup- 
plies 
Display ALL 2
 SYS 0: Valid (FAX/Internet 
FAX)
1: Valid (FAX/Internet 
FAX/HTTP)
2: Invalid 1
 767 Mainte- nance
(Remote) Service Notification setting ALL 0
SYS Enables to set up to 3 
E-mail addresses to be  
sent.(08-768, 777, 778)
0: Invalid 
1: Valid (E-mail) 
2: Valid (FAX) 1
768 Mainte- nance
(Remote) Destination E-mail address ALL - SYS Maximum 192 letter
s 11
769 Mainte- nance
(Remote) Total counter information  
transmission setting
ALL 0
 SYS 0: Invalid
1: Valid 1
770 Mainte- nance
(Remote) Total counter transmission  
date setting
ALL 1
 SYS 1 to 31 1
771 Mainte- nance
(Remote) PM counter notification set- 
ting
ALL 0
 SYS 0: Invalid
1: Valid 1
772 Mainte- nance Dealers name ALL - SYS Maximum 100 letters
Needed at initial regis- 
tration11
773 Mainte- nance Login name ALL - SYS Maximum 20 letters
Needed at initial regis- 
tration11
774 Mainte- nance
(Remote) Display setting of [Service  
Notification] button
ALL 0
 SYS 0: Not displayed
1: displayed 1
775 Mainte- nance
(Remote) Sending error contents of  
equipment
ALL 0
 SYS 0: Invalid
1: Valid 1
776 Mainte- nance
(Remote) Setting total counter trans- 
mission interval 
(Hour/Hour/Minute/Minute) ALL - SYS 1
777 Mainte- nance
(Remote) Destination E-mail address  2
ALL - SYS Maximum 192 letters 11
778 Mainte- nance
(Remote) Destination E-mail address  3
ALL - SYS Maximum 192 letters 11
779 Mainte- nance
(Remote) Notification format selec- 
tion
ALL 0
 SYS 0: Text
1: Text + XML data 1
780 Mainte- nance Remote-controlled service 
polling day selection
Day-1 ALL 0
 SYS 0: OFF
1 to 31: 1st to 31st of a 
month 1
781 Mainte- nance Remote-controlled service  
polling day selection 
Day-2 ALL 0
 SYS 0: OFF
1 to 31: 1st to 31st of a 
month 1
782 Mainte- nance Remote-controlled service  
polling day selection 
Day-3 ALL 0
 SYS 0: OFF
1 to 31: 1st to 31st of a 
month 1
Setting mode (08) 
Code Classifi-
cation Items
Func-
tion Default
 RAM Contents
Proce-
dure
04/09 
						

							June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 123
2
783 Mainte- nance Remote-controlled service  
polling day selection 
Day-4 ALL 0
 SYS 0: OFF
1 to 31: 1st to 31st of a 
month 1
784 Mainte- nance Remote-controlled service  
polling day selection
Sunday ALL 0
 SYS 0: Invalid
1: Valid 1
785 Mainte- nance Remote-controlled service  
polling day selection 
Monday ALL 0
 SYS 0: Invalid
1: Valid 1
786 Mainte- nance Remote-controlled service 
polling day selection 
Tuesday ALL 0
 SYS 0: Invalid
1: Valid 1
787 Mainte- nance Remote-controlled service  
polling day selection 
Wednesday ALL 0
 SYS 0: Invalid
1: Valid 1
788 Mainte- nance Remote-controlled service  
polling day selection 
Thursday ALL 0
 SYS 0: Invalid
1: Valid 1
789 Mainte- nance Remote-controlled service 
polling day selection
Friday ALL 0
 SYS 0: Invalid
1: Valid 1
790 Mainte- nance Remote-controlled service  
polling day selection 
Saturday ALL 0
 SYS 0: Invalid
1: Valid 1
794 Mainte- nance Information of supplies set-
ting of toner cartridge ALL 0
 SYS 0: Invalid
1: Valid 1
796 Mainte- nance Remote-controlled service 
lengthened interval polling 
(End of month) ALL 0
 SYS 0: Invalid
1: Valid 1
797 Mainte- nance Firmware download ALL 0
SYS 0: Accepted
1: Prohibited 1
798 General Notifying address of trial  period end PRT/
SCN 3
 SYS Sets where the end of 
the trial period is to be 
notified.
0: OFF 1: User 
2: Service center 
3: User and service 
center 1
799 General Forcible end of trial period PRT/ SCN- SYS [CANCEL]: Cancel
[EXECUTION]: Forc- 
ible end 
When the “Forcible end  
of trial period” is per- 
formed, “0” is set in the  
code (08-673) to end up  
the trial period forcibly. 3
800-0 Fuser Temperature  control lower  
limit 
(OHP film)Center  
themistor
ALL 8
 M 0:  130°C  1: 135°C
2:  140°C 3: 145°C 
4:  150°C 5: 155°C 
6:  160°C 7: 165°C 
8:  170°C  9: 175°C 
10: 180°C 
11: 185°C 
12: 120°C 4
800-1 Side  themistorALL 6
 M 4
Setting mode (08) 
Code Classifi-
cation Items
Func-
tion Default
 RAM Contents
Proce-
dure
05/05 
						

							e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 124
801-0 Fuser Temperature 
control lower  
limit  
(Thick paper 
1)Center 
themistor
ALL 8
 M 0:  130°C 1: 135°C  
2:  140°C 3: 145°C   
4:  150°C 5: 155°C 
6:  160°C 7: 165°C  
8:  170°C 9: 175°C   
10: 180°C   
11: 185°C
12: 120°C 4
801-1 Side  themistorALL 6
 M 4
802-0 Fuser Temperature  control lower  
limit
(Thick paper  
2)Center 
themistor
ALL 8
 M 0:  130°C   1: 135°C  
2:  140°C 3: 145°C   
4:  150°C   5: 155°C
6:  160°C   7: 165°C   
8:  170°C 9: 175°C   
10: 180°C  
11: 185°C 
12: 120°C 4
802-1 Side  themistorALL 9
 M 4
803-0 Fuser Temperature  control lower  
limit 
(Thick paper  
3)Center 
themistor
ALL 8
 M 0:  130°C   1: 135°C  
2:  140°C 3: 145°C   
4:  150°C  5: 155°C 
6:  160°C   7: 165°C   
8:  170°C 9: 175°C  
10: 180°C   
11: 185°C 
12: 120°C 4
803-1 Side  themistorALL 10
 M 4
804-0 Fuser Temperature  control lower  
limit 
(Envelope)Center  
themistor
ALL 8
 M 0:  130°C   1: 135°C  
2:  140°C 3: 145°C   
4:  150°C   5: 155°C 
6:  160°C   7: 165°C   
8:  170°C 9: 175°C  
10: 180°C   
11: 185°C 
12: 120°C 4
804-1 Side  themistorALL 10
 M 4
805 Charger Main charger bias correc- tion 
(Text/Photo/OHP film) PRT 98
 M Corrects the value of 
the main charger bias 
adjustment (05-210). 1
806 Charger Main charger bias correc- tion 
(Toner Saving Mode/OHP  
film) PRT 98
 M 1
807 Charger Main charger bias correc- tion 
(Text/Photo/OHP film) PPC 98
 M 1
808 Charger Main charger bias correc- tion
(Text/OHP film) PPC 98
 M 1
809 Charger Main charger bias correc- tion 
(Photo/OHP film) PPC 98
 M 1
826 Charger Main charger bias correc- tion 
(Toner saving mode) PRT 128
 M 1
830 Transfer Transfer transformer DC  correction (C) ALL 128
 M Corrects the value of 
the transfer trans- 
former DC output 
adjustment (05-221). 1
Setting mode (08) 
Code Classifi-
cation ItemsFunc-
tion Default
 RAM Contents
Proce-
dure
05/05