Toshiba Estudio 230 Manual

							June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 145
2
1640 Pixel  counter Latest pixel count 
(Toner cartridge reference) PRT 0
 SYS Displays the latest pixel 
count in the printer  
function and toner car- 
tridge reference.
[Unit: 0.01%] 2
1649-0 Pixel  counterPixel count  
distribution 0-5% PPC  SYS The pixel count data 
are divided into 10  
ranges. The number of  
output pages in each  
range is displayed. In  
this code, the distribu-
tions in the copy func- 
tion are displayed.  
[Unit: page]14
1649-1 5.1-10% PPC  SYS 14 
1649-2 10.1-15% PPC  SYS 14 
1649-3 15.1-20% PPC  SYS 14 
1649-4 20.1-25% PPC  SYS 14 
1649-5 25.1-30% PPC  SYS 14
1649-6 30.1-40% PPC  SYS 14 
1649-7 40.1-60% PPC  SYS 14 
1649-8 60.1-80% PPC  SYS 14 
1649-9 80.1- 100%PPC  SYS 14
1650-0 Pixel  counterPixel count  
distribution 0-5% PRT  SYS The pixel count data 
are divided into 10 
ranges. The number of 
output pages in each  
range is displayed. In  
this code, the distribu-
tions in the printer func- 
tion are displayed.  
[Unit: page]14
1650-1 5.1-10% PRT  SYS 14 
1650-2 10.1-15% PRT  SYS 14 
1650-3 15.1-20% PRT  SYS 14 
1650-4 20.1-25% PRT  SYS 14
1650-5 25.1-30% PRT  SYS 14
1650-6 30.1-40% PRT  SYS 14
1650-7 40.1-60% PRT  SYS 14 
1650-8 60.1-80% PRT  SYS 14 
1650-9 80.1- 100%PRT  SYS 14
1651-0 Pixel  counterPixel count  
distribution 0-5% FAX  SYS The pixel count data 
are divided into 10  
ranges. The number of  
output pages in each  
range is displayed. In 
this code, the distribu- 
tions in the FAX func- 
tion are displayed.
[Unit: page]14
1651-1 5.1-10% FAX  SYS 14 
1651-2 10.1-15% FAX  SYS 14 
1651-3 15.1-20% FAX  SYS 14
1651-4 20.1-25% FAX  SYS 14
1651-5 25.1-30% FAX  SYS 14
1651-6 30.1-40% FAX  SYS 14
1651-7 40.1-60% FAX  SYS 14 
1651-8 60.1-80% FAX  SYS 14 
1651-9 80.1- 100%FAX  SYS 14
Setting mode (08) 
Code Classifi-
cation ItemsFunc-
tion Default 
 RAM Contents
Proce-
dure 
						

							e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 146
 
 The management items at PM support mode can also b e operated at setting mode (08).
The following items are displayed or set by using s ub-codes at PM management setting in the table 
below.

0: Present number of output pages - Means the present number of output pages.
1: Recommended number of output pages for replaceme nt
- Means the recommended number of output pages for  replacement.
2: Number of output pages at the last replacement
- Means the number of output pages at the last repl acement.
3: Present driving counts - Means the present drive counts (1 count = 2 secon ds).
4: Recommended driving counts to be replaced - Means the recommended drive counts for replacemen t (1 count = 2 seconds).
5: Driving counts at the last replacement - Means the drive counts at the last replacement.
6: Present output pages for control
- Means the present number of output pages for cont rolling.
7: Present driving counts for control - Means the present drive counts for controlling (1  count = 2 seconds).
8: Number of times replaced
- Counts up when clearing the counter of each unit i n the PM Support Mode Screen.
Notes: 
 Sub-code 3 is equivalent to sub-code 7. 
 When the value of sub-code 3 is changed, the value  of sub-code 7 is also updated and vice 
versa.
 When “0” is set at one of sub-codes 0, 3, 6 and 7,  the rest of them are automatically updated 
to “0”.
05/12 
						

							June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 147
2
Items PM management set-
ting  
*Indicated in 8 digits Date of previous 
replacement 
 Remarks
Photoconductive drum 1150-0 to 8 1151  
Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0 
Sub-code 1: 64,000/74,000/90,000
Sub-code 4: 120,000/120,000/120,000
Drum cleaning blade 1158-0 to 8 1159 
Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0 
Sub-code 1: 64,000/74,000/90,000 
Sub-code 4: 120,000/120,000/120,000
Drum separation finger 1172-0 to 8 1173  
Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0 
Sub-code 1: 64,000/74,000/90,000 
Sub-code 4: 120,000/120,000/120,000
Main charger grid 1174-0 to 8 1175  
Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0 
Sub-code 1: 64,000/74,000/90,000
Sub-code 4: 120,000/120,000/120,000
Needle electrode 1182-0 to 8 1183  
Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0 
Sub-code 1: 64,000/74,000/90,000
Sub-code 4: 120,000/120,000/120,000
Ozone filter 1198-0 to 8 1199 
Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0 
Sub-code 1: 128,000/148,000/180,000 
Sub-code 4: 240,000/240,000/240,000
Developer material 1200-0 to 8 1201  
Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0 
Sub-code 1: 64,000/74,000/90,000 
Sub-code 4: 120,000/120,000/120,000
Transfer charger wire 1214-0 to 8 1215  
Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0 
Sub-code 1: 64,000/74,000/90,000
Sub-code 4: 120,000/120,000/120,000
Separation charger wire 1224-0 to 8 1225 
Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0
Sub-code 1: 64,000/74,000/90,000 
Sub-code 4: 120,000/120,000/120,000
Fuser roller 1246-0 to 8 1247  
Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0 
Sub-code 1: 128,000/148,000/180,000 
Sub-code 4: 240,000/240,000/240,000
Pressure roller 1250-0 to 8 1251  
Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0 
Sub-code 1: 128,000/148,000/180,000
Sub-code 4: 240,000/240,000/240,000
05/12 
						

							e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 148
Cleaning roller 1266-0 to 8 1267  
Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0 
Sub-code 1: 128,000/148,000/180,000 
Sub-code 4: 240,000/240,000/240,000
Fuser roller separation  
finger 1268-0 to 8 1269  
Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0 
Sub-code 1: 128,000/148,000/180,000 
Sub-code 4: 240,000/240,000/240,000
Pickup roller (RADF) 1282-0,1,2,8 1283 
Sub-codes 0, 2, 8: 0/0/0
Sub-code 1: 120,000/120,000/120,000
Feed roller (RADF) 1284-0,1,2,8 1285 
Sub-codes 0, 2, 8: 0/0/0
Sub-code 1: 120,000/120,000/120,000
Separation roller  
(RADF) 1286-0,1,2,8 1287  
Sub-codes 0, 2, 8: 0/0/0
Sub-code 1: 120,000/120,000/120,000
Pickup roller
(Upper drawer) 1290-0,1,2,8 1291  
Sub-codes 0, 2, 8: 0/0/0 
Sub-code 1: 80,000/80,000/80,000
Pickup roller
(Lower drawer) 1292-0,1,2,8 1293  
Sub-codes 0, 2, 8: 0/0/0 
Sub-code 1: 80,000/80,000/80,000
Pickup roller (LCF) 1294-0,1,2,8 1295  
Sub-codes 0, 2, 8: 0/0/0 
Sub-code 1: 160,000/160,000/160,000
Feed roller
(Upper drawer) 1298-0,1,2,8 1299  
Sub-codes 0, 2, 8: 0/0/0 
Sub-code 1: 80,000/80,000/80,000
Feed roller
(Lower drawer) 1300-0,1,2,8 1301  
Sub-codes 0, 2, 8: 0/0/0 
Sub-code 1: 80,000/80,000/80,000
Feed roller (LCF) 1302-0,1,2,8 1303  
Sub-codes 0, 2, 8: 0/0/0 
Sub-code 1: 160,000/160,000/160,000
Separation roller
(Upper drawer) 1306-0,1,2,8 1307  
Sub-codes 0, 2, 8: 0/0/0 
Sub-code 1: 80,000/80,000/80,000
Separation roller
(Lower drawer) 1308-0,1,2,8 1309  
Sub-codes 0, 2, 8: 0/0/0 
Sub-code 1: 80,000/80,000/80,000
Items
PM management set-
ting  
*Indicated in 8 digits Date of previous 
replacement 
 Remarks
05/12 
						

							June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 149
2
Separation roller (LCF) 1310-0,1,2,8 1311  
Sub-codes 0, 2, 8: 0/0/0 
Sub-code 1: 160,000/160,000/160,000
Separation roller 
(PFP upper drawer) 1312-0,1,2,8 1313  
Sub-codes 0, 2, 8: 0/0/0 
Sub-code 1: 80,000/80,000/80,000
Separation roller 
(PFP lower drawer) 1314-0,1,2,8 1315  
Sub-codes 0, 2, 8: 0/0/0 
Sub-code 1: 80,000/80,000/80,000
Separation roller 
(Bypass unit) 1316-0,1,2,8 1317 
Sub-codes 0, 2, 8: 0/0/0 
Sub-code 1: 80,000/80,000/80,000
Feed roller 
(PFP upper drawer) 1320-0,1,2,8 1321 
Sub-codes 0, 2, 8: 0/0/0 
Sub-code 1: 80,000/80,000/80,000
Feed roller 
(PFP lower drawer) 1322-0,1,2,8 1323  
Sub-codes 0, 2, 8: 0/0/0 
Sub-code 1: 80,000/80,000/80,000
Feed roller 
(Bypass unit) 1324-0,1,2,8 1325  
Sub-codes 0, 2, 8: 0/0/0
Sub-code 1: 80,000/80,000/80,000
Pickup roller 
(PFP upper drawer) 1328-0,1,2,8 1329  
Sub-codes 0, 2, 8: 0/0/0
Sub-code 1: 80,000/80,000/80,000
Pickup roller 
(PFP lower drawer) 1330-0,1,2,8 1331  
Sub-codes 0, 2, 8: 0/0/0
Sub-code 1: 80,000/80,000/80,000
Pickup roller 
(Bypass unit) 1332-0,1,2,8 1333  
Sub-codes 0, 2, 8: 0/0/0
Sub-code 1: 80,000/80,000/80,000
Recovery blade 1336-0 to 8 1337  
Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0
Sub-code 1: 64,000/74,000/90,000 
Sub-code 4: 120,000/120,000/120,000
Items
PM management set-
ting  
*Indicated in 8 digits Date of previous 
replacement 
 Remarks
05/12 
						

							e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 150

(1) Turn ON the power while [0] and [8] are pressed  simultaneously.
(2) Key in the code “257” with the digital keys and  press the [START] button (the following is dis-
played).
Note: Note:  Before performing the following operations, note th e current counter values.
 Fig. 2-4
(3) Key in the value “1” or “2” with the digital key and press the [START] button.
The value entered is displayed on the left of the “ %”, and the [ENTER] button is displayed.
Note: Note: 
The value can be erased by pressing the [CLEAR] but ton to change as long as the [START] but-
ton is not pressed. (The value on the left of the “ %” is reset to “0” by pressing the [CLEAR] but-
ton.) 
 Key in “1” to copy the value of the total  counter (LGC board) (A) onto the value of  
the backup counter (SYS board) (B).
 Fig. 2-5
(A)(B)
05/12   
						

							June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 151
2
(4) Press the [ENTER] button to complete overwriting of  the counter value.
Note: Note: 
The screen returns to the code entry screen without  copying (overwriting) the value when the 
[CANCEL] button is pressed.
 Key in “2” to copy the value of the backup 
counter (SYS board) (B) onto the value of  
the total counter (LGC board) (A).
 Fig. 2-6
(A) (B)
05/12  
						

							e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 152
2.2.8 Setting mode (08) (e-STUDIO202L/232/282)
Procedure 1 
* Press [FUNCTION CLEAR] to enter minus (-). 
Procedure 2 
Procedure 3 
Procedure 4 
* Press [FUNCTION CLEAR] to enter minus (-). 
Procedure 5 
* Press [HELP] to enter “-”.
The items in the setting code list can be set or ch
anged in this setting mode (08).
(Stores value in RAM)
[0][8]
[POWER] [POWER] OFF/ON
(Exit)
[Digital key](Code) [START]
[Digital key]
*
[FUNCTION CLEAR]
[ENTER] or
[INTERRUPT]
Sets or
changes value
[CLEAR]
(Corrects value)[CANCEL]
[0][8]
[POWER] [POWER]OFF/ON
(Exit)[Digital key]
(Code) [START] [ENTER]
or
[INTERRUPT]
Adjustment value
cannot be changed
[0][8]
[POWER] [POWER] OFF/ON
(Exit)
[Digital key]
(Code) [START]
[CANCEL] or [CLEAR](Automatic setting)
[ENTER]
or
[INTERRUPT]
(Stores value in RAM)
[0][8]
[POWER] [POWER]
OFF/ON (Exit)
[Digital key]
(Code) [Digital key]
(Sub-code) [Digital key]
*
 [FUNCTION CLEAR]Sets or
changes value
[START] [START]
[ENTER]
or
[INTERRUPT] (Stores value
in RAM)
[CLEAR]
(Corrects value)[CLEAR]
(Corrects value)
[START]
[CANCEL]
[0][8]
[POWER] [POWER] OFF/ON
(Exit)
[Digital key]
(Code) [Digital key]
*[HELP]
[START]
[CANCEL]
[ENTER]
or
[INTERRUPT]
[CLEAR]
(Corrects value) (Stores value in RAM)
Sets or
changes value
05/12 
						

							June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 153
2
Procedure 7 
Procedure 9 
Procedure 10 
Procedure 11 and 12 
*1.  Press [MONITOR/PAUSE] to enter “-”, when enteri ng telephone number.
*2.  The data are stored in SYS-RAM in procedure 11  and stored in NIC-RAM in procedure 12.
Procedure 14
[0][8]
[POWER] [POWER] OFF/ON
(Exit)
[Digital key]
(Code)[Digital key]
(Setting)
[CLEAR]
(Corrects value)
[START](HDD formatting)
[CANCEL]
[ENTER]
or
[INTERRUPT] (Stores value in RAM)
[0][8]
[POWER] [POWER] OFF/ON
(Exit)
[Digital key]
(Code) [Select icon]
[START] [CANCEL]
[ENTER]
or
[INTERRUPT]
[CLEAR]
(Corrects value) (Stores value in RAM)
[0][8]
[POWER] [POWER]
OFF/ON
(Exit)
[Digital key]
(Code) [Digital key]
(1st setting) [Digital key]
(2nd setting)
[START] [START] [CANCEL]
[ENTER]or
[INTERRUPT]
[CLEAR]
(Corrects value) [CLEAR]
(Corrects value) (Stores value in RAM)
[0][8]
[POWER] [POWER] OFF/ON
(Exit)
[Digital key]
(Code) [Digital key]
or
[Software keyboard][START]
[CANCEL]
[CLEAR] 
(Corrects value)*2(Stores value in RAM)*1[MONITOR/PAUSE]
Sets or
changes value [ENTER]
[0][8]
[POWER] [POWER]
OFF/ON (Exit)
[Digital key]
(Code) [Digital key]
(Sub-code)
[CLEAR]
(Corrects value)
[START] [START]
[CANCEL]
[ENTER]
or
[INTERRUPT]
Adjustment value
cannot be changed
05/12 
						

							e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 154
Notes:  The digit after the hyphen in “Code” of the follow ing table is a sub code.
 e-STUDIO202L/232/282: In “RAM”, the NVRAM of the bo ard in which the data of each code
is stored is indicated. “M” stands for the LGC boar d, “SYS”, “NIC”  
and “UTY” stands for the SYS board.
Setting mode (08) 
Code Classifi-
cation Items
Func-
tion Default
 RAM Contents
Proce-
dure
200 General Date and time setting ALL -  - Year/month/date/day/
hour/minute/second 
Example:03 07 0 13 13 27 48 
“Day” - “0” is for  
“Sunday”. Pro- 
ceeds Monday 
through Saturday  
from “1” to “6”. 5
201 General Destination selection ALL EUR: 0 UC: 1
JPN: 2  M 0: EUR
1: UC 
2: JPN 1
202 User  interface Counter installed externally ALL 0
M 0: No external counter
1: Coin controller
2: Copy key card 
3: Key copy counter 1
203 General Line adjustment mode ALL 0 M 0: For factory shipment
1: For line 
* Field: “0” must be selected 1
204 User  interface Auto-clear timer setting ALL 3
SYS Timer to return the 
equipment to the 
default settings when  
the [START] button is  
not pressed after the 
function and the mode  
are set 
0: Not cleared
1 to 10: Set number x  
15 sec. 1
205 User  interface Auto power save mode  
timer setting ALL EUR: 11
UC: 11
JPN: 6
Others:  11
 SYS Timer to automatically 
switch to the Auto  
power save mode when 
the equipment has not  
been used 
0: Invalid 6: 3min. 
7: 4min. 8: 5min. 
9: 7min. 
10: 10min. 
11: 15min. 
12: 20min. 
13: 30min.
14: 45min. 
15: 60min. 1
05/12