Toshiba Estudio 230 Manual
Have a look at the manual Toshiba Estudio 230 Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 566 Toshiba manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 58
e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 22
2.2 Self-diagnosis Modes
Note: Note:
To enter the desired mode, turn ON the power while two digital keys designated to each mode
(e.g. [0] and [5]) are pressed simultaneously.
Control panel check mode (01):
Notes: 1. A mode can be canceled by [POWER] OFF/ON when the LED is lit and the LCD is blinking.
2. Button Check
Buttons with LED (Press to turn OFF the LED.)
Buttons without LED (Press to...](http://img.usermanuals.tech/thumb/76/103453/w64_estudio-230-manual-1513181221_d-57.png "Page 58
e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 22
2.2 Self-diagnosis Modes
Note: Note:
To enter the desired mode, turn ON the power while two digital keys designated to each mode
(e.g. [0] and [5]) are pressed simultaneously.
Control panel check mode (01):
Notes: 1. A mode can be canceled by [POWER] OFF/ON when the LED is lit and the LCD is blinking.
2. Button Check
Buttons with LED (Press to turn OFF the LED.)
Buttons without LED (Press to...")
![Page 59
June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 23
2
List print mode (9S): The procedure varies dependi ng on the code.
PM support mode (6S):
Firmware update mode (89): Refer to “6. FIRMWARE U PDATING”.
Fig. 2-1
*1 Turn OFF the power after using the self-diagnosis modes, and leave the equipment to the user.
[9][START]
[POWER] (Code)
101: Adjustment mode (05)
102: Setting mode (08)
(Code)
103: PM support mode
104: Stored information of pixel...](http://img.usermanuals.tech/thumb/76/103453/w64_estudio-230-manual-1513181221_d-58.png "Page 59
June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 23
2
List print mode (9S): The procedure varies dependi ng on the code.
PM support mode (6S):
Firmware update mode (89): Refer to “6. FIRMWARE U PDATING”.
Fig. 2-1
*1 Turn OFF the power after using the self-diagnosis modes, and leave the equipment to the user.
[9][START]
[POWER] (Code)
101: Adjustment mode (05)
102: Setting mode (08)
(Code)
103: PM support mode
104: Stored information of pixel...")
![Page 60
e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 24
2.2.1 Input check (Test mode 03) (e-STUDIO200L/230/2
80)
Note: Note:
Initialization is performed before the equipment en ters the test mode.
Fig. 2-2 Example of display during input check
Items to be checked and the condition of the equipm ent when the buttons [A] to [H] are highlighted are
listed in the following pages. The status of each input signal can be checked by p
ressing the [FAX] button, and...](http://img.usermanuals.tech/thumb/76/103453/w64_estudio-230-manual-1513181221_d-59.png "Page 60
e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 24
2.2.1 Input check (Test mode 03) (e-STUDIO200L/230/2
80)
Note: Note:
Initialization is performed before the equipment en ters the test mode.
Fig. 2-2 Example of display during input check
Items to be checked and the condition of the equipm ent when the buttons [A] to [H] are highlighted are
listed in the following pages. The status of each input signal can be checked by p
ressing the [FAX] button, and...")
![Page 61
June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 25
2
[FAX] button: OFF ([FAX] LED: OFF)
Digital key Button Items to check Contents
Highlighted display
e.g. Normal dis-
play
e.g.
[1] A -
- -
B LCF connection Not connected Connected
C Bypass unit connection Not connected Connected
D Bypass paper sensor No paper Paper present
E ADU connection Not connected Connected
F ADU opening/closing switch ADU opened ADU closed
G ADU exit sensor Paper present No...](http://img.usermanuals.tech/thumb/76/103453/w64_estudio-230-manual-1513181221_d-60.png "Page 61
June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 25
2
[FAX] button: OFF ([FAX] LED: OFF)
Digital key Button Items to check Contents
Highlighted display
e.g. Normal dis-
play
e.g.
[1] A -
- -
B LCF connection Not connected Connected
C Bypass unit connection Not connected Connected
D Bypass paper sensor No paper Paper present
E ADU connection Not connected Connected
F ADU opening/closing switch ADU opened ADU closed
G ADU exit sensor Paper present No...")
![Page 62
e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 26
[5]
A LCF end fence home position sensor Fence home
positionOther than
home position
B LCF end fence stop position sensor Fence stop positionOther than
stop position
C LCF standby side empty sensor No paper Paper present
D LCF side cover opening/closing switch Cover closed C over opened
E LCF motor rotation status (Motor is rotating at ou tput mode
(03)) Abnormal rota-
tionNormal rota-
tion
F LCF...](http://img.usermanuals.tech/thumb/76/103453/w64_estudio-230-manual-1513181221_d-61.png "Page 62
e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 26
[5]
A LCF end fence home position sensor Fence home
positionOther than
home position
B LCF end fence stop position sensor Fence stop positionOther than
stop position
C LCF standby side empty sensor No paper Paper present
D LCF side cover opening/closing switch Cover closed C over opened
E LCF motor rotation status (Motor is rotating at ou tput mode
(03)) Abnormal rota-
tionNormal rota-
tion
F LCF...")
![Page 63
June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 27
2
Table 1. Relation between the status of the bypass paper width sensor and paper size (width).
[0]A -
- -
B - - -
C - - -
D Lower drawer detection switch Drawer not installedDrawer
present
E Lower drawer paper stock sensor Paper almost emptyPaper present
F - - -
G - - -
H - - -
Bypass paper-width sensor Paper-width size
2 1 0
1 1 1 A3/A4
1 1 0 B5-R
1 0 1 A5-R
1 0 0 A3/A4
0 1 1 Card size
0 1 0...](http://img.usermanuals.tech/thumb/76/103453/w64_estudio-230-manual-1513181221_d-62.png "Page 63
June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 27
2
Table 1. Relation between the status of the bypass paper width sensor and paper size (width).
[0]A -
- -
B - - -
C - - -
D Lower drawer detection switch Drawer not installedDrawer
present
E Lower drawer paper stock sensor Paper almost emptyPaper present
F - - -
G - - -
H - - -
Bypass paper-width sensor Paper-width size
2 1 0
1 1 1 A3/A4
1 1 0 B5-R
1 0 1 A5-R
1 0 0 A3/A4
0 1 1 Card size
0 1 0...")
![Page 64
e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 28
[FAX] button: ON ([FAX] LED: ON)
Digital key Button Items to check Contents
Highlighted display
e.g. Normal dis-
play
e.g.
[1] A -
- -
B - - -
C 24 V power supply Power ON Power OFF
D IPC board connection Not connected Connected
E - - -
F Polygonal motor rotation status (Motor is rotating at Output
Mode (03)) Abnormal rota-
tionNormal rota-
tion
G Auger lock switch Lock Unlock
H Toner cartridge...](http://img.usermanuals.tech/thumb/76/103453/w64_estudio-230-manual-1513181221_d-63.png "Page 64
e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 28
[FAX] button: ON ([FAX] LED: ON)
Digital key Button Items to check Contents
Highlighted display
e.g. Normal dis-
play
e.g.
[1] A -
- -
B - - -
C 24 V power supply Power ON Power OFF
D IPC board connection Not connected Connected
E - - -
F Polygonal motor rotation status (Motor is rotating at Output
Mode (03)) Abnormal rota-
tionNormal rota-
tion
G Auger lock switch Lock Unlock
H Toner cartridge...")
![Page 65
June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 29
2
[5] A -
- -
B - - -
C - - -
D - - -
E - - -
F RADF connection RADF con-
nected Not connected
G Platen sensor Platen cover
opened Platen cover
closed
H Carriage home position sensor Carriage at home positionOther than
home position
[6] A -
- -
B - - -
C - - -
D APS sensor (APS-R) No original Original
present
E APS sensor (APS-C) No original Original
present
F APS sensor (APS-3) No original...](http://img.usermanuals.tech/thumb/76/103453/w64_estudio-230-manual-1513181221_d-64.png "Page 65
June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 29
2
[5] A -
- -
B - - -
C - - -
D - - -
E - - -
F RADF connection RADF con-
nected Not connected
G Platen sensor Platen cover
opened Platen cover
closed
H Carriage home position sensor Carriage at home positionOther than
home position
[6] A -
- -
B - - -
C - - -
D APS sensor (APS-R) No original Original
present
E APS sensor (APS-C) No original Original
present
F APS sensor (APS-3) No original...")
![Page 66
e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 30
Table 2. Connecting status of additional options at inner area of the equipment
[9]A Bridge unit/Job Separator/Offset Tray connection d
etection-
3 Refer to table 2
B Bridge unit/Job Separator/Offset Tray connection d etection-
2 Refer to table 2
C Bridge unit/Job Separator/Offset Tray connection d etection-
1 Refer to table 2
D - - -
E - - -
F - - -
G - - -
H - - -
[0] A Dongle (for Printer/Scanner kit...](http://img.usermanuals.tech/thumb/76/103453/w64_estudio-230-manual-1513181221_d-65.png "Page 66
e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 30
Table 2. Connecting status of additional options at inner area of the equipment
[9]A Bridge unit/Job Separator/Offset Tray connection d
etection-
3 Refer to table 2
B Bridge unit/Job Separator/Offset Tray connection d etection-
2 Refer to table 2
C Bridge unit/Job Separator/Offset Tray connection d etection-
1 Refer to table 2
D - - -
E - - -
F - - -
G - - -
H - - -
[0] A Dongle (for Printer/Scanner kit...")
June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 25 2 [FAX] button: OFF ([FAX] LED: OFF) Digital key Button Items to check Contents Highlighted display e.g. Normal dis- play e.g. [1] A - - - B LCF connection Not connected Connected C Bypass unit connection Not connected Connected D Bypass paper sensor No paper Paper present E ADU connection Not connected Connected F ADU opening/closing switch ADU opened ADU closed G ADU exit sensor Paper present No paper H ADU entrance sensor Paper present No paper [2] A PFP upper drawer detection switch Drawer not installedDrawer present B - - - C PFP upper drawer paper stock sensor Paper almost emptyPaper present D PFP upper drawer feed sensor Paper present No paper E PFP connection Not connected Connected F PFP side cover opening/closing switch Cover opened C over closed G PFP upper drawer empty sensor No paper Paper present H PFP upper drawer tray-up sensor Tray at upper limit positionOther than upper limit position [3] A LCF tray bottom sensor Tray at bottom position Other than bottom posi- tion B LCF standby side paper mis-stacking sensor Correct st ack- ing Incorrect stacking C - - - D - - - E LCF drawer detection switch Drawer not installedDrawer present F - - - G - - - H LCF feed side paper stock sensor Paper almost emptyPaper present [4] A PFP lower drawer detection sensor Drawer not installedDrawer present B - - - C PFP lower drawer paper stock sensor Paper almost emptyPaper present D PFP lower drawer feed sensor Paper present No paper E PFP motor rotation status (Motor is rotating at ou tput mode (03)) Abnormal rota- tionNormal rota- tion F - - - G PFP lower drawer empty sensor No paper Paper present H PFP lower drawer tray-up sensor Tray at upper limit positionOther than upper limit position 05/12
e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 26 [5] A LCF end fence home position sensor Fence home positionOther than home position B LCF end fence stop position sensor Fence stop positionOther than stop position C LCF standby side empty sensor No paper Paper present D LCF side cover opening/closing switch Cover closed C over opened E LCF motor rotation status (Motor is rotating at ou tput mode (03)) Abnormal rota- tionNormal rota- tion F LCF tray-up sensor Tray at upper limit position Other than upper limit position G LCF feed sensor No paper Paper present H LCF feed side empty sensor Paper present No paper [6] A - - - B - - - C - - - D - - - E 1st transport sensor Paper present No paper F - - - G Upper drawer empty sensor No paper Paper present H Upper drawer tray-up sensor Tray at upper limit positionOther than upper limit position [7] A - - - B - - - C - - - D - - - E 2nd transport sensor Paper present No paper F - - - G Lower drawer empty sensor No paper Paper present H Lower drawer tray-up sensor Tray at upper limit positionOther than upper limit position [8] A - - - B Bypass feed paper width sensor-2 Refer to table 1 C Bypass feed paper width sensor-1 Refer to table 1 D Bypass feed paper width sensor-0 Refer to table 1 E - - - F - - - G - - - H - - - [9] A - - - B - - - C - - - D Upper drawer detection switch Drawer not installedDrawer present E Upper drawer paper stock sensor Paper almost emptyPaper present F - - - G - - - H - - - Digital key Button Items to check Contents Highlighted display e.g. Normal dis- play e.g. 05/11
June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 27 2 Table 1. Relation between the status of the bypass paper width sensor and paper size (width). [0]A - - - B - - - C - - - D Lower drawer detection switch Drawer not installedDrawer present E Lower drawer paper stock sensor Paper almost emptyPaper present F - - - G - - - H - - - Bypass paper-width sensor Paper-width size 2 1 0 1 1 1 A3/A4 1 1 0 B5-R 1 0 1 A5-R 1 0 0 A3/A4 0 1 1 Card size 0 1 0 A4-R/A5 0 0 1 B6-R 0 0 0 B4-R/B5 Digital key Button Items to check Contents Highlighted display e.g. Normal dis- play e.g. 05/11
e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 28 [FAX] button: ON ([FAX] LED: ON) Digital key Button Items to check Contents Highlighted display e.g. Normal dis- play e.g. [1] A - - - B - - - C 24 V power supply Power ON Power OFF D IPC board connection Not connected Connected E - - - F Polygonal motor rotation status (Motor is rotating at Output Mode (03)) Abnormal rota- tionNormal rota- tion G Auger lock switch Lock Unlock H Toner cartridge installation switch OFF ON [2] A Registration sensor Paper present No paper B Exit sensor Paper present No paper C Auto-toner sensor connection Not connected Connected D Front cover opening/closing switch Cover opened Cove r closed E - - - F Side cover opening/closing sensor Cover opened Cover closed G Transfer cover opening/closing switch Cover opened C over closed H Main motor rotation status (Motor is rotating at O utput Mode (03)) Abnormal rota- tionNormal rota- tion [3] A - - - B Key copy counter connection Not connected Connected C Job Separator upper stack sensor (When Job Separator is installed) Paper full Paper not full Offset Tray separate sensor (When Offset Tray is in stalled) Separator at home position Other than home position D Fuser unit connection Fuser unit installed Fuser unit not installed E Bridge unit transport sensor-2 (When bridge unit is installed) No paper Paper present F Bridge unit cover opening/closing detection switch (When Bridge unit is installed) Cover opened Cover closed Job Separator cover switch (When Job Separator is installed) Cover opened Cover closed Offset Tray cover switch (When Offset Tray is insta lled) Cover opened Cover closed G Bridge unit paper full detection sensor (When bridge unit is installed) Paper not full Paper full Job Separator lower stack sensor (When Job Separator is installed) Paper full Paper not full Offset Tray stack sensor (When Offset Tray is instal led) Paper full Paper not full H Bridge unit transport sensor-1 (When bridge unit is installed) No paper Paper present Job Separator feed sensor (When Job Separator is installed) Paper present No paper Offset Tray feed sensor (When Offset Tray is install ed) Paper present No paper [4] A - - - B - - - C - - - D - - - E - - - F Bypass feed sensor No paper Paper present G - - - H High-voltage power supply abnormality (shutdown) d etec- tion Normal Abnormal 05/11
June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 29 2 [5] A - - - B - - - C - - - D - - - E - - - F RADF connection RADF con- nected Not connected G Platen sensor Platen cover opened Platen cover closed H Carriage home position sensor Carriage at home positionOther than home position [6] A - - - B - - - C - - - D APS sensor (APS-R) No original Original present E APS sensor (APS-C) No original Original present F APS sensor (APS-3) No original Original present G APS sensor (APS-2) No original Original present H APS sensor (APS-1) No original Original present [7] A RADF tray sensor Original present No original B RADF empty sensor Original present No original C RADF jam access cover switch Cover opened Cover close d D RADF opening/closing sensor RADF opened RADF closed E RADF exit sensor Original present No original F RADF reverse sensor Original present No original G RADF read sensor Original present No original H RADF registration sensor Original presentNo original [8] A - - - B - - - C - - - D - - - E RADF original length sensor Original presentNo original F RADF original width sensor-1 Original presentNo original G RADF original width sensor-2 Original presentNo original H RADF original width sensor-3 Original presentNo original Digital key Button Items to check Contents Highlighted display e.g. Normal dis- play e.g. 05/11
e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 30 Table 2. Connecting status of additional options at inner area of the equipment [9]A Bridge unit/Job Separator/Offset Tray connection d etection- 3 Refer to table 2 B Bridge unit/Job Separator/Offset Tray connection d etection- 2 Refer to table 2 C Bridge unit/Job Separator/Offset Tray connection d etection- 1 Refer to table 2 D - - - E - - - F - - - G - - - H - - - [0] A Dongle (for Printer/Scanner kit (GM-2020 or 2030)) Connectable Not connect- able B Dongle (for Printer kit (GM-1020 or 1030)) Connecta ble Not connect- able C Dongle (for Scanner upgrade kit (GM-3020 or 3030)) Connectable Not connect- able D Dongles for other equipments/Other USB devices Conn ectable Not connect- able E - - - F - - - G - - - H - - - Bridge unit Job Separator Offset Tray None Bridge unit/Job Separator/Offset Tray connection detection-3 Normal display Highlighting displayHighlighting display Highlighting display Bridge unit/Job Separator/Offset Tray connection detection-2 Highlighting display Highlighting display Normal display Highlighting display Bridge unit/Job Separator/Offset Tray connection detection-1 Normal display Normal display Normal display Highlight ing display Digital key Button Items to check Contents Highlighted display e.g. Normal dis- play e.g. 05/11
June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 31 2 2.2.2 Input check (Test mode 03) (e-STUDIO202L/232/2 82) Note: Note: Initialization is performed before the equipment en ters the test mode. Fig. 2-3 Example of display during input check Items to be checked and the condition of the equipm ent when the buttons [A] to [H] are highlighted are listed in the following pages. The status of each input signal can be checked by p ressing the [FAX] button, and the digital keys in the test mode (03). [0][3] [POWER] [START] [FAX] [Digital keys] [CLEAR](LCD ON) [POWER] OFF/ON (Exit) 05/12
e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 32 [FAX] button: OFF ([FAX] LED: OFF) Digital key Button Items to check Contents Highlighted display e.g. Normal dis- play e.g. [1] A - - - B LCF connection Not connected Connected C Bypass unit connection Not connected Connected D Bypass paper sensor No paper Paper present E ADU connection Not connected Connected F ADU opening/closing switch ADU opened ADU closed G ADU exit sensor Paper present No paper H ADU entrance sensor Paper present No paper [2] A PFP upper drawer detection switch Drawer not installedDrawer present B - - - C PFP upper drawer paper stock sensor Paper almost emptyPaper present D PFP upper drawer feed sensor Paper present No paper E PFP connection Not connected Connected F PFP side cover opening/closing switch Cover opened C over closed G PFP upper drawer empty sensor No paper Paper present H PFP upper drawer tray-up sensor Tray at upper limit positionOther than upper limit position [3] A LCF tray bottom sensor Tray at bottom position Other than bottom posi- tion B LCF standby side paper mis-stacking sensor Correct st ack- ing Incorrect stacking C - - - D - - - E LCF drawer detection switch Drawer not installedDrawer present F - - - G - - - H LCF feed side paper stock sensor Paper almost emptyPaper present [4] A PFP lower drawer detection sensor Drawer not installedDrawer present B - - - C PFP lower drawer paper stock sensor Paper almost emptyPaper present D PFP lower drawer feed sensor Paper present No paper E PFP motor rotation status (Motor is rotating at ou tput mode (03)) Abnormal rota- tionNormal rota- tion F - - - G PFP lower drawer empty sensor No paper Paper present H PFP lower drawer tray-up sensor Tray at upper limit positionOther than upper limit position 05/11
June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 33 2 [5] A LCF end fence home position sensor Fence home positionOther than home position B LCF end fence stop position sensor Fence stop positionOther than stop position C LCF standby side empty sensor No paper Paper present D LCF side cover opening/closing switch Cover closed C over opened E LCF motor rotation status (Motor is rotating at ou tput mode (03)) Abnormal rota- tionNormal rota- tion F LCF tray-up sensor Tray at upper limit position Other than upper limit position G LCF feed sensor No paper Paper present H LCF feed side empty sensor Paper present No paper [6] A - - - B - - - C - - - D - - - E 1st transport sensor Paper present No paper F - - - G Upper drawer empty sensor No paper Paper present H Upper drawer tray-up sensor Tray at upper limit positionOther than upper limit position [7] A - - - B - - - C - - - D - - - E 2nd transport sensor Paper present No paper F - - - G Lower drawer empty sensor No paper Paper present H Lower drawer tray-up sensor Tray at upper limit positionOther than upper limit position [8] A - - - B Bypass feed paper width sensor-2 Refer to table 1 C Bypass feed paper width sensor-1 Refer to table 1 D Bypass feed paper width sensor-0 Refer to table 1 E - - - F - - - G - - - H - - - [9] A - - - B - - - C - - - D Upper drawer detection switch Drawer not installedDrawer present E Upper drawer paper stock sensor Paper almost emptyPaper present F - - - G - - - H - - - Digital key Button Items to check Contents Highlighted display e.g. Normal dis- play e.g. 05/11
e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 34 Table 1. Relation between the status of the bypass paper width sensor and paper size (width). [0]A - - - B - - - C - - - D Lower drawer detection switch Drawer not installedDrawer present E Lower drawer paper stock sensor Paper almost emptyPaper present F - - - G - - - H - - - Bypass paper-width sensor Paper-width size 2 1 0 1 1 1 A3/A4 1 1 0 B5-R 1 0 1 A5-R 1 0 0 A3/A4 0 1 1 Card size 0 1 0 A4-R/A5 0 0 1 B6-R 0 0 0 B4-R/B5 Digital key Button Items to check Contents Highlighted display e.g. Normal dis- play e.g. 05/11