Toshiba Estudio 230 Manual

							June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 195
2
758 Mainte- nance 
(Remote) Information about supplies 
Part number of toner car- 
tridge ALL - SYS Maximum 20 digits 11
759 Mainte- nance
(Remote) Information about supplies 
Order quantity of toner car-
tridge ALL 1
 SYS 1
760 Mainte- nance
(Remote) Information about supplies 
Condition number of toner  
cartridge ALL 1
 SYS 1
764 Mainte- nance
(Remote) Automatic ordering sup- 
plies 
Result table printout ALL 1
 SYS 0: OFF
1: Always
2: ON Error 1
765 Mainte- nance
(Remote) Automatic ordering sup- 
plies
Display ALL 2
 SYS 0: Valid (FAX/Internet 
FAX)
1: Valid (FAX/Internet  FAX/HTTP)
2: Invalid 1
 767 Mainte- nance
(Remote) Service Notification setting ALL 0
SYS Enables to set up to 3 
E-mail addresses to be  
sent.(08-768, 777, 778) 
0: Invalid
1: Valid (E-mail)
2: Valid (FAX) 1
768 Mainte- nance
(Remote) Destination E-mail address ALL - SYS Maximum 192 letter
s 11
769 Mainte- nance
(Remote) Total counter information 
transmission setting
ALL 0
 SYS 0: Invalid
1: Valid 1
770 Mainte- nance
(Remote) Total counter transmission  
date setting
ALL 1
 SYS 1 to 31 1
771 Mainte- nance
(Remote) PM counter notification set- 
ting
ALL 0
 SYS 0: Invalid
1: Valid 1
772 Mainte- nance Dealers name ALL - SYS Maximum 100 letters
Needed at initial regis-
tration11
773 Mainte- nance Login name ALL - SYS Maximum 20 letters
Needed at initial regis- 
tration11
774 Mainte- nance
(Remote) Display setting of [Service  
Notification] button
ALL 0
 SYS 0: Not displayed
1: displayed 1
775 Mainte- nance
(Remote) Sending error contents of  
equipment
ALL 0
 SYS 0: Invalid
1: Valid 1
776 Mainte- nance
(Remote) Setting total counter trans- 
mission interval 
(Hour/Hour/Minute/Minute) ALL - SYS 1
777 Mainte- nance
(Remote) Destination E-mail address  2
ALL - SYS Maximum 192 letters 11
778 Mainte- nance
(Remote) Destination E-mail address  3
ALL - SYS Maximum 192 letters 11
Setting mode (08) 
Code Classifi-
cation ItemsFunc-
tion Default
 RAM Contents
Proce-
dure
05/11 
						

							e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 196
779 Mainte-
nance
(Remote) Notification format selec- 
tion
ALL 0
 SYS 0: Text
1: Text + XML data 1
780 Mainte- nance Remote-controlled service 
polling day selection 
Day-1 ALL 0
 SYS 0: OFF
1 to 31: 1st to 31st of a  
month 1
781 Mainte- nance Remote-controlled service  
polling day selection 
Day-2 ALL 0
 SYS 0: OFF
1 to 31: 1st to 31st of a 
month 1
782 Mainte- nance Remote-controlled service  
polling day selection 
Day-3 ALL 0
 SYS 0: OFF
1 to 31: 1st to 31st of a 
month 1
783 Mainte- nance Remote-controlled service  
polling day selection
Day-4 ALL 0
 SYS 0: OFF
1 to 31: 1st to 31st of a 
month 1
784 Mainte- nance Remote-controlled service  
polling day selection 
Sunday ALL 0
 SYS 0: Invalid
1: Valid 1
785 Mainte- nance Remote-controlled service 
polling day selection 
Monday ALL 0
 SYS 0: Invalid
1: Valid 1
786 Mainte- nance Remote-controlled service  
polling day selection 
Tuesday ALL 0
 SYS 0: Invalid
1: Valid 1
787 Mainte- nance Remote-controlled service  
polling day selection 
Wednesday ALL 0
 SYS 0: Invalid
1: Valid 1
788 Mainte- nance Remote-controlled service  
polling day selection
Thursday ALL 0
 SYS 0: Invalid
1: Valid 1
789 Mainte- nance Remote-controlled service  
polling day selection 
Friday ALL 0
 SYS 0: Invalid
1: Valid 1
790 Mainte- nance Remote-controlled service 
polling day selection 
Saturday ALL 0
 SYS 0: Invalid
1: Valid 1
794 Mainte- nance Information of supplies set- 
ting of toner cartridge ALL 0
 SYS 0: Invalid
1: Valid 1
796 Mainte- nance Remote-controlled service
lengthened interval polling 
(End of month) ALL 0
 SYS 0: Invalid
1: Valid 1
797 Mainte- nance Firmware download ALL 0
SYS 0: Accepted
1: Prohibited 1
798 General Notifying address of trial  period end PRT/
SCN 3
 SYS Sets where the end of 
the trial period is to be 
notified. 
0: OFF 1: User
2: Service center 
3: User and service center 1
Setting mode (08) 
Code Classifi-
cation ItemsFunc-
tion Default
 RAM Contents
Proce-
dure
05/11 
						

							June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 197
2
799 General Forcible end of trial period PRT/ SCN- SYS [CANCEL]: Cancel
[EXECUTION]: Forc- 
ible end 
When the “Forcible end 
of trial period” is per- 
formed, “0” is set in the  
code (08-673) to end up  
the trial period forcibly. 3
800-0 Fuser Temperature  control lower  
limit
(OHP film)Center  
themistor
ALL 8
 M 0:  130°C  1: 135°C
2:  140°C 3: 145°C 
4:  150°C 5: 155°C
6:  160°C 7: 165°C 
8:  170°C  9: 175°C 
10: 180°C
11: 185°C 
12: 120°C 4
800-1 Side  themistorALL 6
 M 4
801-0 Fuser Temperature  control lower  
limit  
(Thick paper  
1)Center  
themistor
ALL 8
 M 0:  130°C 1: 135°C  
2:  140°C 3: 145°C   
4:  150°C 5: 155°C 
6:  160°C 7: 165°C   
8:  170°C 9: 175°C  
10: 180°C  
11: 185°C 
12: 120°C 4
801-1 Side  themistorALL 6
 M 4
802-0 Fuser Temperature  control lower  
limit 
(Thick paper  
2)Center  
themistor
ALL 8
 M 0:  130°C   1: 135°C  
2:  140°C 3: 145°C   
4:  150°C   5: 155°C 
6:  160°C   7: 165°C   
8:  170°C 9: 175°C  
10: 180°C   
11: 185°C 
12: 120°C 4
802-1 Side  themistorALL 9
 M 4
803-0 Fuser Temperature  control lower  
limit 
(Thick paper 
3)Center  
themistor
ALL 8
 M 0:  130°C   1: 135°C  
2:  140°C 3: 145°C   
4:  150°C  5: 155°C 
6:  160°C   7: 165°C   
8:  170°C 9: 175°C   
10: 180°C   
11: 185°C
12: 120°C 4
803-1 Side  themistorALL 10
 M 4
804-0 Fuser Temperature  control lower  
limit 
(Envelope)Center  
themistor
ALL 8
 M 0:  130°C   1: 135°C  
2:  140°C 3: 145°C   
4:  150°C   5: 155°C 
6:  160°C   7: 165°C   
8:  170°C 9: 175°C   
10: 180°C  
11: 185°C 
12: 120°C 4
804-1 Side  themistorALL 10
 M 4
Setting mode (08) 
Code Classifi-
cation ItemsFunc-
tion Default
 RAM Contents
Proce-
dure
05/11 
						

							e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 198
805 Charger Main charger bias correc-
tion 
(Text/Photo/OHP film) PRT 98
 M Corrects the value of 
the main charger bias 
adjustment (05-210). 1
806 Charger Main charger bias correc- tion 
(Toner Saving Mode/OHP  
film) PRT 98
 M 1
807 Charger Main charger bias correc- tion 
(Text/Photo/OHP film) PPC 98
 M 1
808 Charger Main charger bias correc- tion
(Text/OHP film) PPC 98
 M 1
809 Charger Main charger bias correc- tion 
(Photo/OHP film) PPC 98
 M 1
826 Charger Main charger bias correc- tion 
(Toner saving mode) PRT 128
 M 1
830 Transfer Transfer transformer DC  correction (C) ALL 128
 M Corrects the value of 
the transfer trans- 
former DC output  
adjustment (05-221). 1
831 Separa- tionSeparation transformer DC 
correction (C) ALL 128
 M Corrects the value of 
the separation trans- 
former DC output  
adjustment (05-234). 1
833 Devel- operDeveloper bias DC correc-
tion 
(Text/Photo/OHP film) PRT 108
 M Corrects the value of 
the developer bias 
adjustment (05-205). 1
834 Devel- operDeveloper bias DC correc- 
tion 
(Toner Saving Mode/OHP  
film) PRT 108
 M 1
835 Devel- operDeveloper bias DC correc- 
tion 
(Text/Photo/OHP film) PPC 108
 M 1
836 Devel- operDeveloper bias DC correc- 
tion 
(Text/OHP film) PPC 108
 M 1
837 Devel- operDeveloper bias DC correc- 
tion 
(Photo/OHP film) PPC 108
 M 1
838 Image  process-ing Switching of recycled toner  
saving control 
ALL 0
 M 0: Switched
1: Not switched 1
839 Image  process-
ing Correction by temperature/ 
humidity
ALL 0
 M Sets the correction by 
temperature/humidity. 
0: All valid
1: All invalid 
2: Valid only in auto-
toner sensor
3: All valid except  transfer and separa- 
tion 1
Setting mode (08) 
Code Classifi-
cation ItemsFunc-
tion Default
 RAM Contents
Proce-
dure
05/11 
						

							June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 199
2
849 General Power source setting for  destination ALL SAD: 1
Others: 0 M 0: Other than SAD
1: SAD 1
859 Devel- operDeveloper bias DC correc- 
tion
(Toner saving mode) PRT 128
 M Corrects the value of 
the developer bias 
adjustment (05-205). 1
860 Devel- operDeveloper bias DC correc- 
tion (Normal) PRT 128
 M Corrects the value of 
the developer bias  
adjustment (05-205). 1
861 Devel- operDeveloper bias DC correc- 
tion (Text/Photo) PPC 128
 M Corrects the value of 
the developer bias  
adjustment (05-205). 1
862 Devel- operDeveloper bias DC correc- 
tion (Text) PPC 128
 M Corrects the value of 
the developer bias  
adjustment (05-205). 1
863 Devel- operDeveloper bias DC correc- 
tion (Photo) PPC 128
 M Corrects the value of 
the developer bias  
adjustment (05-205). 1
864 Charger Main charger bias correc- tion (Normal) PRT 128
 M Corrects the value of 
the main charger bias 
adjustment 
(05-210). 1
865 Charger Main charger bias correc- tion (Text/Photo) PPC 128
 M Corrects the value of 
the main charger bias  
adjustment 
(05-210). 1
866 Charger Main charger bias correc- tion (Text) PPC 128
 M Corrects the value of 
the main charger bias  
adjustment 
(05-210). 1
867 Charger Main charger bias correc- tion (Photo) PPC 128
 M Corrects the value of 
the main charger bias  
adjustment 
(05-210). 1
868 Transfer Transfer transformer DC  correction (H) ALL 128
 M Corrects the value of 
the transfer trans- 
former DC output  
adjustment (05-220). 1
869 Transfer Transfer transformer DC  correction (L) ALL 128
 M Corrects the value of 
the transfer trans- 
former DC output  
adjustment (05-222). 1
870 Separa- tionSeparation transformer DC  
correction (H) ALL 128
 M Corrects the value of 
the separation trans-
former DC output  
adjustment (05-233). 1
871 Separa- tionSeparation transformer DC  
correction (L) ALL 128
 M Corrects the value of 
the separation trans- 
former DC output  
adjustment (05-235). 1
872 Laser Laser power correction  (Normal) PRT 128
 M Corrects the value of 
the laser power adjust- 
ment (05-286). 1
873 Laser Laser power correction  (Text/Photo) PPC 128
 M Corrects the value of 
the laser power adjust-
ment (05-286). 1
Setting mode (08) 
Code Classifi-
cation Items
Func-
tion Default
 RAM Contents
Proce-
dure
05/11 
						

							e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 200
875 Laser Laser power correction 
(Toner saving mode) PRT 128
 M Corrects the value of 
the laser power adjust- 
ment (05-286). 1
876 Laser Laser power correction  (Text) PPC 128
 M Corrects the value of 
the laser power adjust- 
ment (05-286). 1
877 Laser Laser power correction  (Photo) PPC 128
 M Corrects the value of 
the laser power adjust-
ment (05-286). 1
886 Fuser Temperature drop control  setting in ready status  
(Temperature/Time) ALL 2
 M 0:  None
1:  Pattern 1
2:  Pattern 2 
3:  Pattern 3
4:  Pattern 4 
5:  Pattern 5 
6:  Pattern 6
7:  Pattern 7 
8: Pattern 8 
9:  Pattern 9
10: Pattern 10 
11: Pattern 11 
12: Pattern 12
13: Pattern 13 
14: Pattern 14 
15: Pattern 15 
16: Pattern 16 
17: Pattern 17 
18: Pattern 18 
19: Pattern 19
20: Manual adjustment 1
896-0 Fuser Temperature  control lower  
limit
(Plain paper/ 
Low tempera- 
ture)Center  
themistor
ALL 7
 M 0:  130°C 1: 135°C
2:  140°C 3: 145°C 
4:  150°C 5: 155°C
6:  160°C 7: 165°C 
8:  170°C 9: 175°C 
10: 180°C
11: 185°C 
12: 120°C 4
896-1 Side  themistorALL 5
 M 4
900 Version System firmware ROM ver- sion ALL - - JPN: T377SY0JXXX
UC: T377SY0UXXX 
EUR: T377SY0EXXX 
Others: T377SY0XXXX 2
903 Version Engine ROM version ALL - - 377M-XXX 2 
905 Version Scanner ROM version ALL - - 377S-XXX 2
907 Version RADF ROM version ALL - - DF-XXXX 2
908 Version Finisher ROM version ALL - - SDL-XX FIN-XX 2
915 Version Fax board ROM version FAX - - F562-XXX 2
920 Version FROM basic section soft- ware version ALL - - VX.XX/X.XX 2
921 Version FROM internal program ALL - - VXXX.XXX X 2
922 Version UI data fixed section ver- sion ALL - - VXXX.XXX X 2
923 Version UI data common section  version ALL - - VXXX.XXX X 2
924 Version Version of UI data lan- guage 1 in HDD ALL - - VXXX.XXX X 2
Setting mode (08) 
Code Classifi-
cation ItemsFunc-
tion Default
 RAM Contents
Proce-
dure
05/11 
						

							June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 201
2
925 Version Version of UI data lan- guage 2 in HDD ALL - - VXXX.XXX X 2
926 Version Version of UI data lan- guage 3 in HDD ALL - - VXXX.XXX X 2
927 Version Version of UI data lan- guage 4 in HDD ALL - - VXXX.XXX X 2
928 Version Version of UI data lan- guage 5 in HDD ALL - - VXXX.XXX X 2
929 Version Version of UI data lan- guage 6 in HDD ALL - - VXXX.XXX X 2
930 Version Version of UI data in  FROM displayed at power- 
ON ALL - - VXXX.XXX X 2
931 Version Version of UI data lan- guage 7 in HDD ALL - - VXXX.XXX X 2
933 Version Web data whole version ALL - - VXXX.XXX X 2 
934 Version Web UI data in HDD Version: Language 1 ALL - - VXXX.XXX X 2
935 Version Web UI data in HDD Version: Language 2 ALL - - VXXX.XXX X 2
936 Version Web UI data in HDD Version: Language 3 ALL - - VXXX.XXX X 2
937 Version Web UI data in HDD Version: Language 4 ALL - - VXXX.XXX X 2
938 Version Web UI data in HDD Version: Language 5 ALL - - VXXX.XXX X 2
939 Version Web UI data in HDD Version: Language 6 ALL - - VXXX.XXX X 2
944 Version HD version ALL - - JPN: T377HD0JXXX UC: T377HD0UXXX 
EUR: T377HD0EXXX 
Others: T377HD0XXXX2
945 Network Two-way setting of RawPort 9100 ALL 2
 UTY 1: Valid
2: Invalid 12
947 General Initialization after software  version upgrade ALL - - Perform this code when 
the software in this 
equipment has been  
upgraded. 3
949 General Automatic interruption  page setting during printing ALL 0
 SYS Sets the number of 
pages to interrupt the  
printing automatically. 
0-100: 0 to 100 pages 1
950 Elec- tronic Fil-ing Start-up method of Elec- 
tronic Filing
ALL 0
 SYS Sets the start-up 
method of the Elec-
tronic Filing. 
0: Standard 
1: Forced start-up (Not 
recovered)
2: Forced start-up 
(Recovered) 1
953 User  interface Access code entry for 
Electronic Filing printing ALL 0
 SYS 0: Renewed automati-
cally
1: Enter every time 1
Setting mode (08) 
Code Classifi-
cation ItemsFunc-
tion Default
 RAM Contents
Proce-
dure
05/11 
						

							e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 202
954 User 
interface Clearing timing for files and  
Electronic Filing Agent ALL 1
 SYS 0: Immediately after 
the completion of  
scanning
1: Cleared by Auto 
Clear 1
969 User  interface Error sound ALL 1
SYS 0: OFF
1: ON 1
970 User  interface Sound setting when  
switching to Energy Saving 
Mode ALL 1
 SYS 0: OFF
1: ON 1
972 User interface Enables/disables the dis- 
play that the toner is nearly  
empty  ALL 0
 SYS 0:  Disabled
1: Enabled 1
973 Network PCL line feed code setting PRT 0 SYS Sets the PCL line feed 
code. 
0: Automatic setting 
1: CR=CR, LF=LF
2: CR=CR+LF, LF=LF 
3: CR=CR, LF=CR+LF 1
975 General Job handling when print- ing is short paid with coin  
controller ALL 1
 SYS Sets whether pause or 
stop the printing job 
when it is short paid 
using a coin controller. 
0: Pause the job 
1: Stop the job 1
976 Elec- tronic Fil-ing Equipment name and user 
name setting to a folder  
when saving files ALL 0
 SYS Sets whether or not 
adding the equipment 
name and user name to  
the folder when saving  
files.  
0: Not add 
1: Add the equipment 
name 
2: Add the user name  1
977 Network Switching of extended  ASCII code in catFs file- 
system ALL 0
 SYS 0: ISO8859-1
1: ISO8859-2 1
978 Network Raw printing job (Paper feeding drawer) PRT 0
 SYS 0: AUTO
1: Upper drawer 
2: Lower drawer
3: PFP upper drawer 
4: PFP lower drawer 
5: LCF 1
Setting mode (08) 
Code Classifi-
cation ItemsFunc-
tion Default
 RAM Contents
Proce-
dure
05/11 
						

							June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 203
2
979 Network Raw printing job (PCL symbol set) PRT 0
 SYS 0:  Roman-8
1:  ISO 8859/1 Latin 1 
2: ISO 8859/2 Latin 2 
3: ISO 8859/9 Latin 5
4: PC-8,Code Page 437
5: PC-8 D/N, Danish/ Norwegian
6: PC-850,Multilingual 
7: PC-852, Latin2 
8:  PC-8 Turkish 
9:  Windows 3.1 Latin 1 
10: Windows 3.1 Latin 2 
11: Windows 3.1 Latin 5 
12: DeskTop 
13: PS Text
14: Ventura Interna- tional
15: Ventura US 
16: Microsoft Publishing 
17: Math-8 
18: PS Math 
19: Ventura Math
20: Pi Font 
21: Legal 
22: ISO 4: United King-
dom
23: ISO 6: ASCII
24: ISO 11 
25: ISO 15: Italian 
26: ISO 17 
27: ISO 21: German 
28: ISO 60: Danish/Nor-
wegian
29: ISO 69: French
30: Windows 3.0 Latin 1 
31: MC Text 
32: PC Cyrillic 
33: ITC Zapf Dingbats 
34: ISO 8859/10 Latin 6 
35: PC-775
36: PC-1004 
37: Symbol 
38: Windows Baltic
39: Wingdings 1
980 Elec- tronic Fil-
ing Electronic Filing data  
retention period when NIC  
board is not installed
(Public Box) ALL 0
 SYS 0: Retention OFF
1 to 999: 1 to 999 days 1
981 Elec- tronic Fil-
ing Electronic Filing data  
retention period when NIC  
board is not installed
(User Box) ALL 0
 SYS 0: Retention OFF
1 to 999: 1 to 999 days 1
985 Elec- tronic Fil-
ing Print mode setting of mixed  
input source of Electronic  
Filing ALL 0
 SYS 0: Image quality prior-
ity mode
1: Function priority  mode 1
Setting mode (08) 
Code Classifi-
cation ItemsFunc-
tion Default
 RAM Contents
Proce-
dure
05/11 
						

							e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 204
986 General Copy function setting PPC 0
SYS Sets the copy function 
to be invalid. 
0: Valid 
1: Invalid 1
988 Paper  feeding Setting of paper size  
switching to 13” LG ALL 0
 SYS 0: Not switched
1: LG  13”LG
2: FOLIO   13”LG 1
995 Version Equipment number (serial  number) display ALL 0
 SYS This code can be also 
keyed in from the  
adjustment mode (05- 
976). 
10 digits 11
999 Mainte- nance FSMS total counter ALL 0
SYS Refers to values of total 
counter 1
1002 Network Selection of NIC board sta- tus information ALL 1
 NIC 1: Not printed out 
when the equipment 
is restarted
2: Printed out when  the equipment is 
restarted 12
1003 Network Communication speed and  settings of Ethernet  ALL 1
 NIC 1: Auto
2: 10MBPS Half  Duplex
3: 10MBPS Full 
Duplex
4: 100MBPS Half  Duplex
5: 100MBPS Full 
Duplex 12
1006 Network Address Mode ALL 2 NIC 1: Fixed IP address
2: Dynamic IP address 
(DHCP)
3: Dynamic IP address  (DHCP) without 
AutoIP 12
1007 Network Domain name ALL - NIC Maximum 96 letters 12 
1008 Network IP address ALL - NIC 000.000.000.000- 255.255.255.255 
(Default value 
000.000.000.000)12
1009 Network Subnet mask ALL - NIC 000.000.000.000- 255.255.255.255 
(Default value  
000.000.000.000)12
1010 Network Gateway ALL - NIC 000.000.000.000- 255.255.255.255 
(Default value 
000.000.000.000)12
1011 Network Availability of IPX ALL 1 NIC 1: Available
2: Not available 12
1012 Network Network frame type ALL 1 NIC 1: Automatic
2: IEEE802.3
3: Ethernet II 
4: IEEE802.3SNAP 
5: IEEE802.2 12
Setting mode (08) 
Code Classifi-
cation Items
Func-
tion Default
 RAM Contents
Proce-
dure
05/11