TiE Onyx 2, 3, 4, 5 Service And Programming Manual

							A- TOLL RESTRICTION
AP- TOLL RESTRICTION 
 For   
  
						

							C- CLASS OF SERVICE
CL- LIST COS
Description
Use this option to list the programmed Class of Service.
None
Default I 
 extensions  COS 
The attendant has COS 
See chart below for details.
Data Ports 
 Permanent Receive/Transmit Connection have COS 29.
Refer to the Data Products Manual.
The port pairs assigned to the STI have COS 31.
Feature
Automatic Call Distribution
Call Forwarding
Call Waiting
Callback
Centralized Attendant Service
Direct Inward Dialing
Direct Inward Dialing/Tie Lines
Direct Trunk Access
Distinctive Ringing
Flash
Intrusion
OPA
Paging
Privacy
Silent Monitor
Speed Dial
Toll Restriction
Transfer
Universal Night Answer
Related
Programming
None
Feature Reference
COS Option
Byte/Bit
ACD Supervisor Kevset
Inhibit Call Forwarding
Allow Off-Premise Call Forwarding
Inhibit Camp-On
Allow Callback Prioritv
Allow Bell Standard for CASBYO:O
Allow Automatic Op. Intercept for DID BYO:O
Absorb 1st Digit for DID/Tie Trunks
BYO: 1
Direct Trunk  Camp-On
Single Ring OPX
 Flash for  Line Sets
Allow Break-In 
Inhibit OPA Transfers to Extension
Inhibit Access to Page Zone 3
Inhibit Access to Page Zone 2
Inhibit Access to Page Zone 1
Inhibit Access to All Call PagingBY2: 1
Allow Privacy
Allow Silent Monitor
Inhibit System Speed Dial
Allow Only Intercom Calls at Night
Allow Only Local Calls at Night
Allow Only Local Calls (Day or Night)
Extension Toll Restriction Level
Allow Extended Ring
Operator Call Pickup (ONYX IV)
System Reports, Diagnostics and Maintenance Utilities
These options are enabled (1) in   (for attendants)
cos 1
Default
O-No
O-No
O-No
O-No
O-No
O-No
O-No
O-No’
O-No
O-No
O-No’
O-No
O-No
O-No
O-No
O-No
O-No
O-No
O-No
O-No
O-No
O-No
O-No ---
O-No
O-Yes
Issue 1-OSOFTWARE CONFIGURATION2-35 
						

							C- CLASS OF SERVICE
CL- LIST COS
Instructions
To enter data on the PRF:
No entry required.
To enter data at the programming terminal:
Step 1 Press CL. The Class of Service listing displays. See below for a partial
COS CONFIGURATION l *** l **. 
BIT7 BIT6BIT5 BIT4BIT3BIT2
BYO:INH SYS SPEED DIALINH CALL FWDINH  ONBREAK-IN
OFF-i ICM  ONLY OPA BELL
CBACK PRIORITYPRIVACY EXTENDED RINGLOCAL CALL ATLOCAL ONLYTOLL RESTRICT 
BY2:SINGLE RG OPX NO  SLS  MONITORINH PG  2INH PG  INH  P C DIR
cos 
 0 0 : 00010000 ooooo-o 00000000
cos  0 1 : 00000000 ooooo-o 00000000
through
COS  27: 00000000  00000000
 INTERCEPT
NIGHT
PG  3LINE  ON
2-36   Issue 1-O 
						

							  2-2 PROGRAM RECORD FORM, CLASS OF SERVICE
      
 076
543210 765432-O
     
Tech Info Inc.
Call I-800-T.B. SOLVE
July 08, 1998
 PM
Tie  Nitsuko Digital Systems
Class of service: Class of service can be intimidating. This page is
taken from the DCW DCH Programming record form. This should
help. If you have any further questions please call (810) 39591 II, for
technical assistance. 
						

							 CLASS OF SERVICE
CP- 
 SYSTEM SPEED DIAL 
Description
Related
Programming
l
l
Feature Reference
Instructions
Step  l
Step I 
Step  l
Issue 1-O
Use this option to  (0) or deny (1) extensions with this COS the ability to
use System Speed Dial. This option also restricts System Speed Dial for
 trunks and incoming tie trunks.
Condition.5
This option does not apply to CO trunks.
Default 
System Speed Dial enabled (0).
Speed Dial
E- Extensions. 
 Class of Service  Assign Class of Service to extensions.
E- Extensions, EB- Personal Speed Dial 
  Assign a Speed Dial block
to an extension. Extensions can share a block, thereby sharing the Extension
Speed Dial numbers.
QD- Number of System Speed Dial Digits 
 Assign the number of System
Speed  Dial  digits  (2. 3 or 4). This allows either 10, 100 or 1000  System
Speed Dial numbers.
Speed Dial
To enter data on the PRF:
On Table 2 for 
 enter 0 to enable System Speed Dial for each COS.
Enter 1 to disable System Speed Dial.
To enter data at the programming terminal:
Type CP. You see: COS 
 00: 00010000  00000001
Enter data for each COS you want to program.
SOFTWARE CONFIGURATION 
2-37 
						

							C- CLASS OF SERVICE
CP- INHIBIT 
 FORWARDING 
Use this option to allow (0) or  (1) on-premise Call Forwarding-for
extensions with this COS. For system attendants (in COS 00). use 
to  the Alternate Attendant and Removing Trunks and Extensions
From Service features.
Conditions
None
Default Value
 Forwarding and Alternate Attendant enabled (0).
Related
Programming
l
Call Forwarding
CP- Allow Off-Premise Call Forwarding 
  For each COS, allow or
deny Off-Premise Call Forwarding.
E- Extensions, 
 Class of Service  Assign a COS to each extension.
Feature Reference
Alternate Attendant
Call Forwarding
Removing Trunks and Extensions From Service
Instructions
Step 1 
Step 1 
Step  l
To enter data on the PRF:
On Table 2 for 
 enter 0 to enable Call Forwarding for each COS. Enter
1 to disable Call Forwarding.
To enter data at the programming terminal:
Type CP. You see: COS # 
00: 00010000  00000001
Enter data for each COS you want to program.
 4 R F    Issue 1-r) 
						

							C- CLASS OF SERVICE
CP- INHIBIT CAMP-ON 
Description
Related
Programming
l
Feature Reference
Instructions
Step  
Step 1 
Step  
Issue 1-OUse this option to allow (0) or 
 (1) a user’s ability to send Call Waiting
(Camp-On) tones to a 
 extension  dialing 2. (To allow/deny a user’s
ability to Camp-On to a 
 trunk. refer to 
None
Default 
Camp-On to extensions allowed (0).
Call Waiting (Camp-On)
CP- Direct Trunk Access and Trunk Camp-On   An extension
user with Direct Trunk Access can camp-on to a busy trunk.
E- Extensions. 
 Class of Service  Assign Class of Service to extensions.
QJ- Intercom Call Control, Alerts 
 Allow or deny Call Waiting indications
system wide.
Call Waiting (Camp-On)
To enter data on the PRF:
On Table 2 for 
 enter 0 to enable Camp-On for each COS. Enter 1 to
disable Camp-On.
To enter data at the programming terminal:
Type CP. You see: COS # 
00: 00010000 00000-O 00000001
Enter data for each COS you want to program.
SOFIWARE CONFIGURATION 
2-39 
						

							C- CLASS OF SERVICE
CP- ALLOW BREAK-IN (INTRUSION) 
Description
Related
Programming
l
Feature Reference
Instructions
Step  l
Step 1 l
Step  
Use this option to enable (1) or disable (0) Intrusion for extensions  this
cos.
Conditions
None
Intrusion allowed ( 1) at COS 0.
Intrusion not 
 (0) at all other 
Intrusion
CP- Allow Privacy 
  Enable/disable Privacy for each Class of
Service. If an extension has Privacy. another extension cannot Intrude on its
calls.
E- Extensions. 
 Class of Service  Assign Class of Service to extensions.
Intrusion
To enter data on the PRF:
On Table 
 for  enter 0 to disable Intrusion for each COS.  Enter 1 
enable Intrusion.
To enter data at the programming terminal:
Type CP. You see: COS 
 00: 00010000  00000001
Enter data for each COS you want to program.
    Issue 1-O 
						

							C- CLASS OF SERVICE
 ALLOW  CALL FORWARDING 
Description
Related
Programming
l
Feature Reference
Instructions
Step  
Step  l
Step  l
Use this option to allow (  or  (0) Off-Premise Call Forwarding for
extensions 
  COS.
Off-Premise Call  requires either ground start trunks or loop start
trunks 
 disconnect 
Default  
Off-Premise Call  not allowed (0).
Call Forwarding
CP- Inhibit Call Forwarding 
  For each COS, allow or deny Call
Forwarding.
E- Extensions. 
 Class of Service  Assign a COS to each extension.
Call Forwarding
To enter data on the PRF:
On Table 2 for 
 enter 0 to disable Off-Premise Call Forwarding. Enter
1 to enable Off-Premise 
 Forwarding.
To enter data at the programming terminal:
Type CP. You see: COS 
 00: 00010000  00000001
Enter data for each COS  want to program.
Issue 1-OSOFTWARE CONFIGURATION2-41 
						

							C- CLASS OF 
CP- ALLOW ONLY    NIGHT 
Description
Related
Programming
l
l
l
Use this option to restrict estensions with this COS to only Intercom calls at
night. If enabled in an estension’s COS. the user can only place Intercom
calls when the 
 is in the night mode. The user cannot place  outside
calls (including 
   calls). When enabled  this option overrides AP- Toll
Restriction  programming. This option also pertains to incoming tie trunk
callers.
None
Default 
Estensions not restricted to Intercom calls a night (0).
Toll Restriction
AI- Initialize Toll Restriction 
 Initialize Toll Restriction before
programming.
AP- Toll Level 
 Enter the Toll Level vou want to program.
AP- Allow Active Dial Pad 
 Enable/disable continued dialing for this Toll
Level (see Special Services and OCC Compatibility).
 Allow Special Access  1) Dialing  Enable/disable  and 
dialing for this Toll Level.
AP- Allow Outside Operator 
 Dialing  Enable/disable outside operator
dialing for this Toll Level.
AP- Allow International Dialing 
 Enable/disable direct international dialing
for this Toll Level.
AP- Allow Equal Access 
Enable/disable Equal Access Dialing for this Toll
Level (see Equal Access Compatibility). Also, program the Equal Access
Codes table.
AP- Allow 1 + 
 Dialing  Enable/disable long distance exchange calls
for this Toll Level. Also, program the 1 + NNX codes table.
  NNS Dialing  Enable/disable local exchange (NNX) dialing for
this Toll Level. Also, program the NNX codes table.
AP- Allow NPA Dialing 
 Enable/disable area code (NPA) dialing for this
Toll Level. Also. program the NPA codes table.
 Six Digit Analysts  Enable/disable six-digit analysis for this Toll Level.
Also, program a six-digit analysis table.
CP- Allow Only Local Calls at Night 
  At night, extensions with
this option enabled can place Intercom calls and local outside calls. This
assignment overrides AP programming (except AP- Allow Active Dial Pad).
CP- Allow 
 Local Calls (Day or Night)  (BY   Extensions with this
option enabled can only place Intercom calls or local outside calls. This
assignment overrides AP programming (except AP- Allow Active Dial Pad).
CP- Extension Toll Restriction Level 
  Assign a toll restriction
level (O-7) to a Class of Service.
E- Extensions, 
 Class of Service  Assign Class of Service to extensions.
E- Trunks, E J- Toll Restriction 
 Enable/disable Toll Restriction for each
trunk.--
2-42 SOFTWARE CONFIGURATIONIssue 1-O