Stiga TITAN TITAN 740 DC TITAN 740 DCR Instructions Manual

							81
ENGLISHEN
Original instructions for use
3.4.3.2 Adjusting steering wheel height (1:C2)
Do not adjust the steering wheel during 
operation.
The height of the steeri ng wheel is steplessly ad-
justable.
Undo the knob on the steering column and raise or 
lower the steering wheel to the desired position. 
Tighten.
3.4.3.3 Headlamp and horn (1:C3) (740DCR)The lever has the following functions:
Horn
Turn signal lamps (1:N)
Parking lights
Headlights (1:M)
See the symbols on the control for the relevant 
function.
3.4.3.4 Adjusting steering wheel angle (1:C4)Do not adjust the steering wheel during 
operation.
The steering wheel can be set at different angles 
steplessly
Release the control on the side of the steering col-
umn and set the steering wh eel to the desired an-
gle. Tighten the control.
3.4.3.5 Drive / service brake (1:C5)
If rapid deceleration becomes necessary 
the pedal should be  reversed sharply. 
NOTE! This make s the operator 
affected by powerful forces.
Never press the drive pedal when 
parking brake is activated. This puts 
unnormal load on the parking brake 
and shortens its service life. 
The pedal determines the  gear ratio between the 
engine and the driven wheels (= speed). The 
service brake is activated when the pedal is 
released or pressed to wards neutral position.
1. Press the pedal forwards - 
the machine starts to move for-
wards.
2. No load on the pedal  – the 
machine is stationary.
3. Pedal moved backwards  – 
the machine reverses.
4 The pedal is pressed towards neutral position 
-  the machine breaks. In case of an emergency and the 
machine does not brake as expected 
when the pedal is reversed, the left 
pedal (1:C6) should be used as an 
emergency brake. 
NOTE! This puts 
unnormal load on  the parking brake 
and shortens its service life. 
3.4.3.6 Parking brake / Emergency brake (1:C6)Never press the pedal while driving 
except for in an emergency. Pressing the 
pedal while driving reduces the service 
life of the parking brake wich results in 
a loss of functionality.
The pedal has the following 
functions:
•When stopping . Parking 
brake.
• During operation . Emergency 
brake.
Indicator (1:I4) lights when the pedal is completely 
depressed.
3.4.3.7 Hazard warning lights (1:C7).The switch is used to activate the hazard 
warning lights. All the turn signal lamps 
and the indicator (1:I4) flash at the same 
time.
3.4.3.8 Inhibitor, parking brake (1:C8)
Never press the drive pedal (1:C5) 
when parking brake  is activated. This 
puts unnormal load on the parking 
brake and shortens  its service life. 
The inhibitor locks the pedal (1:C6) in the 
depressed position. The function is used to 
lock the machine on slopes, when trans-
porting, etc. when the engine is not run-
ning.
Locking:
1. Depress the pedal (1:C 6) fully. The indicator 
(1:I4) lights.
2. Press the inhibitor
3. Release the pedal.
Releasing:
1. Depress the pedal (1:C6) fully. 
2. Release the pedal.
3.4.4 Controls – instrument panel
3.4.4.1 Throttle control (1:E1).Control for setting the engine’s revs.
Front position  - Full throttle - when the machine 
is in operation, full throttle should always be used. 
Rear position - Idling. 
						

							82
ENGLISHEN
Original instructions for use
3.4.4.2 Ignition lock (1:E2)The ignition lock is used for starting and stopping 
the engine. 
Four positions:Preheat position:  The cylinders are heat-
ed to facilitate starting. Hold in this posi-
tion as below at lower temperatures before 
starting the engine.
Max 5 seconds
Stop position:  The engine is stopped. The 
key can be removed.
Operating position:  Bypassed at start-up 
and used when the engine is running.
Start position:  The electric starter motor 
is activated when the key is turned to the 
spring-loaded starting position. Once the 
engine has started, let the key return to the 
operating position.
3.4.4.3 Implement lifter (1:Ls)This control controls both the hydraulic tool lift at 
the front of the machine (1:L) and the lift cylinder 
for tools installed under the cab. These are con-
nected in series.
The control (1:Ls) only works when the engine is 
running.
However, it can be lowered to the floating position 
when the engine is off. 
Never leave the machine with the imple-
ment in the transpor t position. Risk of 
serious crushing injuries by the imple-
ment as it lowers quickly if the control 
is unintentionally affected.
The lever has the four following positions: Floating position . Move the lever to its 
front position, where it locks. The imple-
ment is now lowered to its floating posi-
tion.
In the floating position, the implement 
always rests against the ground at the 
same pressure and can follow the con-
tours of the ground. 
Use the floating position when carrying 
out work. 
Lowering . The implement lowers re-
gardless of its weight. The lowering 
force is determined by the implement’s 
weight and the hydraulic down force that 
is applied when lowering.
Locking in the transport position . The 
lever has returned to the neutral position 
after raising and lowering. The imple-
ment is locked in the transport position. Raising
. Move the lever to the rear posi-
tion until the implement is in the highest 
position (transport position). Then re-
lease the lever to lock in the transport po-
sition.
3.4.4.4 Hydraulic control (1:Aux1s)This control is used to control certain functions de-
pending on the attached implement.
The control only works when the engine is running 
and the implement’s hydraulic hoses for the in-
tended function are connected to the hydraulic out-
put (1:Aux1).
3.4.4.5 Hydraulic control (1:Aux2s)This control is used to control certain functions de-
pending on the attached implement.
The control only works when the engine is running 
and the implement’s hydraulic hoses for the in-
tended function are connected as follows:
• Implement at the front via the hydraulic outputs 
(1:Aux2f).
• Implement at the rear  via the hydraulic output 
(1:Aux2r).
See also 3.4.4.9
Both hydraulic outputs on the rear section are con-
nected in parallel.
3.4.4.6 Switch (1:Ss)The switch can be used to smoothly set the 
cutting height of the cutting deck with 
electric cutting height adjustment. 
The switch controls the contact (1:S) with 
switching polarity.
3.4.4.7 Switch (1:PTOs)A lever for engaging and disengaging the opera-
tion of the front mounted implement. Two posi-
tions: 1. Press the front part  of the switch – PTO 
engages. The symbol will light up.
2. Press the rear part  of the switch – PTO 
disengages. 
To prevent unnecessary in creases in pressure in 
the hydraulic system, set the throttle control to 
1/4 throttle before the hydraulic PTO is en-
gaged.
The control activates a valve that transfers the 
power from the hydraulic pump to the front mount-
ed implement.
The power is then transferred hydraulically to the 
tool via the hydraulic output at the front (1:PTO).
3.4.4.8 Switch (1:Ys)The switch has three positions and can be 
used for the sand spreader for example.
The switch controls the contact (1:Y).12V 
						

							83
ENGLISHEN
Original instructions for use
3.4.4.9 Switch (1:Aux2fr)The switch has two positions and indicates 
which hydraulic output will be activated 
by the control (1:Aux2s). Front mounted 
hydraulic output (1:Aux2f) or rear mounted hy-
dralic output (1:Aux2r).  See also 3.4.4.5
3.4.5 Controls - other
3.4.5.1 Locking pins front (1:D1)The machine has front and rear sockets for differ-
ent implements. The relevant implement is locked 
by two locking pins after installation. 
To secure the implement on the implement lift:
1. Insert the locking pin fully from the outside.
2. Place your foot on the locking pin and turn  backwards until it locks.
Do not turn the locking pin backwards 
using your hands. Risk  of crushing in-
juries.
To  r e l e a s e :
1. Turn the locking pin forwards until it unlocks.
2. Pull out the locking pin.
3.4.5.2 Locking pins rear(1:F1)The machine has front and rear sockets for differ-
ent implements. The relevant implement is locked 
by two locking pins after installation. The rear 
locking pins self-lock in their grooves after instal-
lation.
3.4.5.3 Main switch (1:F2)Before carrying out work on the elec-
trical system, the power must be cut 
using the main switch.
3.4.5.4 Door holder (1:G1)The door holder is designed to hold the door in the 
partially open position to increase ventilation.
If the door holder  misses the door catch 
when closing, the cab will be damaged.
Check that the door holder engages the door catch 
correctly when used.
3.4.5.5 Engine casingThe machine may not be operated un-
less the engine casing is closed and 
locked. Risk of burns and crushing in-
juries.
To access components on the engine, there are four 
detachable covers. Open the covers as follows:
Cover on the right and left sides (1:Q)
Removing
:
1. Remove the front and re ar rubber straps (1:P). 2. Pull the cover upward, fold it down and pull it 
out.
Installing
:
1. Lower the cover over the inside of the wheel.
2. Hook the cover’s upper part into the machine’s  V-groove and insert the locating pin at the bot-
tom.
3. Hook on the front and  rear rubber straps.
Front cover (1:R)
Removing
:
1. Remove the two front rubber straps.
2. Open the locking knobs (4:B).
3. Move the cover forward and upward.
Installing
:
1. Align the cover.
2. Insert the locking knob lugs in the holes on top  and close the locking knobs.
3. Hook on the two rubber straps.
3.4.5.6 3Electrical socket for trailer (1:V)Seven-pin socket for trailer. 
3.4.5.7 Fuel cap (3:A)The fuel cap for filling diesel is located at the rear 
of the cab.
3.4.5.8 Disengagement lever (5:F)A lever for disengaging the  variable transmission. 
Enables the machine to be moved.
The disengagement le ver must never be 
between the outer an d inner positions. 
This overheats  and damages the 
transmission.
The machine must never be towed but 
may only be moved to and from a 
trailer, if necessary. Towing damages 
the transmission.
The lever has the following two positions:
Lever inwards
:
The hydraulic pump is engaged for normal use.
Lever outwards
:
The hydraulic oil is conne cted passed the hydraulic 
pump and can flow around the system without the 
hydraulic pump blocking the flow. The machine 
can be moved. The flow is restricted, however, and 
is why relatively large force is required to move 
the machine.
3.5 INDICATORS
3.5.1 Fuel gauge (1:I1)
The fuel gauge indicates the level of the fuel in the 
fuel tank.
3.5.2 Indicator for seat suspension (1:I2)
Shows the seat suspension setting. See 3.4.1.2.
0
1 
						

							84
ENGLISHEN
Original instructions for use
3.5.3 Indicator for turn signal/hazard warning lamps (1:I3)
The indicator flashes at the same time as the turn 
signal lamps/hazard  warning lamps flash.
3.5.4 Brake indicator (1:I4)
Never operate the machin e with the brake indi-
cator illuminated. Parking brake and emergen-
cy brake will be affected.
The brake indicator gives a warning that 
the parking brake (1:C7) is activated.
See 3.4.3.6.
3.5.5 Battery charging indicator (1:I5)
Never run the engine with the charging 
indicator illuminated. This will drain the 
battery. The battery charging indicator is only ac-
tivated when the ignition is in the operat-
ing position.
The battery charging indicator gives a warning 
when the engine’s alternator stops charging the 
battery. When the engine is not running the indica-
tor should illuminate as the alternator does not 
generate any charge.
When the engine is running the indicator should 
not be illuminated. If the indicator illuminates dur-
ing operation, the battery  discharges and the en-
gine cannot be started.  Take the machine to an 
authorised workshop for repair.
3.5.6 Hydraulic oil temperature indicator 
(1:I6)
The engine must never be run when the 
temperature indicator is illuminated. 
Risk of serious  engine damage.
The hydraulic oil temperature indicator is 
only activated when the ignition is in the 
operating position.
The hydraulic oil temperature indicator gives a 
warning when the hydraulic oil temperature ex-
ceeds a harmful level.
When the engine is running the indicator should 
not be illuminated. If the indicator illuminates dur-
ing operation, carry out the following:
• Set the throttle control to idle. Do  not stop the 
engine.
• Clean away any leaves , grass or any other ob-
jects from the outside of the oil cooler. See 5.12.
• Leave the engine idling until the temperature  has dropped, the indicator has gone out. The 
machine can then be used as normal.
• If the temperature has not dropped within 5  minutes,  stop the engine and take the machine 
to an authorised workshop for repair. 3.5.7 Engine temperature indicator (1:I7)
Too high engine temperature is indicated partly by 
the indicator and partly by a buzzer that sounds.
The engine must ne ver be loaded or 
operated at more than  idle speed with 
the temperature indicator illuminated 
or when the buzzer sounds. Risk of 
serious engine damage.
The engine temperature indicator and 
buzzer are only activated when the igni-
tion is in the operating position.
The engine temperature indicator and buzzer give 
a warning when the engine temperature exceeds a 
harmful level.
When the engine is running the indicator should 
not be illuminated and the buzzer should not 
sound. If the indicator illu minates or if the buzzer 
sounds during operation, carry out the following:
• Set the throttle control to idle. Do  not stop the 
engine.
• Clean away any leaves, grass or any other ob- jects from the outside of the radiator. See 5.12.
• Leave the engine idling until the temperature  has dropped, the indicator has gone out and the 
buzzer stopped. The machine can then be used 
as normal.
• If the temperature has not dropped within 5  minutes,  stop the engine and take the machine 
to an authorised workshop for repair.
In the event of an indication of too high engine 
temperature, check the  coolant level. See 5.4.
3.5.8 Oil pressure indicator (1:I8) The engine must never be run when the 
oil pressure indicator is illuminated. 
Risk of serious  engine damage.
The oil pressure indicator is only acti-
vated when the ignition is in the oper-
ating position.
The oil pressure indicator gives a warning when 
the engine oil pressure falls below a harmful level. 
When the engine is not running the indicator 
should illuminate as there is no oil pressure.
When the engine is running the indicator should 
not be illuminated. If the indicator illuminates dur-
ing operation, stop the engine immediately and 
take the machine to an authorised workshop for re-
pair.
3.5.9 Hour meter engine (1:I9)
Indicates the number of working hours. Only 
works when the engine is running. 
						

							85
ENGLISHEN
Original instructions for use
3.5.10 Air filter indicator (5:I10)
The indicator warns of a blocked air filter. If the in-
dicator is red, the air filter must be replaced. Then 
reset the indicator by pressing its button.
3.5.11 Hydraulic oil level indicator (7:I11)
The oil level must be visible through the transpar-
ent glass when the machine is level.
If the oil level is too high there is a risk of oil flow-
ing out through the bleed valve. If the oil level is 
too low there is a risk of an increase in the oil tem-
perature and damage to the hydraulic system.
4 AREAS OF USE
The machine may only be used together with orig-
inal accessories.
Optional kits are available for the machine that 
contain the equipment required in order to drive on 
public roads. The contents of the kits are adapted 
according to local regulations. Contact an autho-
rised dealer for purchase information and pur-
chase.
5 STARTING AND OPERATION
The machine may not be operated 
unless the engine casing is closed and 
locked. Risk of burns and crushing 
injuries.
Ensure no one is near the pivot point of 
the machine when the engine is 
running. There is a risk of serious 
crushing injury between the machine’s 
rear and front sections.
Depending on the implement used, 
counter weights might have to be 
mounted on the machine. The axle 
pressure  of a wheel axle may never 
exceed 900 kg or 70% of the total 
weight of the machine
5.1 ACTIONS BEFORE STARTINGCarry out the following before starting the ma-
chine:
• Check/top up with fuel.
• Check the engine oil level.
• Check the coolant level.
• Check to make sure that the air filter indicator 
has not been tripped.
• Check that the water separator’s and fuel filter’s  taps are open.
• Check that the water separator does not contain  water. Drain  if necessary.
• Check the oil level in  the hydraulic tank. See 
3.5.11. • Carry out safety checks.
• Check that a counterweight or accessory weigh-
ing at least 60 kg is installed on the rear of the 
machine when driving with the cutting deck.
• Check that the disengagement lever is in the in- ner position. See 3.4.5.8.
The above actions are described below.
5.2 REFUELLING
Diesel is highly inflammable. Always 
store fuel in contai ners that are made 
especially for this purpose. 
Only fill or top up with fuel outdoors, 
and never smoke when filling or 
topping up. Fill up with fuel before 
starting the engine. 
Never remove the fuel  cap or fill with 
fuel while the engine is running or still 
warm.
The engine must not be run on rapeseed 
diesel (RME). Contact the engine 
supplier for additional information.
Filling fuel up into the filler pipe results 
in fuel leakage an d risk of fire.
Only use diesel which satisfies the requirements in 
2.1.
1. Open the fuel cap (3:A).
2. Fill with diesel up to the lower part of the filler  pipe. If fuel is filled up into the filler pipe, fuel 
will leak out because it expands when heated.
3. Close the fuel cap.
5.3 LEVEL CHECK, ENGINE OILCheck the oil level every  time before using to 
ensure it is correct. The machine should be 
standing on  level ground.
Check the following:
1. Wipe clean around the oil dipstick (5:K), and  pull it up.
2. Wipe the dipstick. 
3. Slide the dipstick down completely and pull up  again. 
4. Read off the oil level. The oil level should be  within the markings  (5:K1) on the dipstick.
If necessary, remove the oil  filler cap (5:G) and fill 
up the oil up to the mark.
Use oil grade API CF or higher,  but not CG, CI-4 
is recommended, and according to the temperature 
diagram below. 
						

							86
ENGLISHEN
Original instructions for use
Never use oil additives.
The oil level must never  go below the lower mark-
ing. This can cause the engine to overheat. Drain 
the oil to the correct level if the oil level exceeds 
the mark. See 6.7.
Reinstall the oil filer cap once the oil level has 
been adjusted.
5.4 LEVEL CHECK, COOLANT
The temperature indicator will not 
work if there is no coolant. This results 
in engine failure.
Check the coolant level ev ery time before use to 
ensure it is correct.
Check the following:
1. The engine must be cold when checking.
2. Remove the front engi ne cover. See 3.4.5.2.
3. Unscrew the radiator cap (8:Q) and check that  the coolant level reach the filler hole.
4. Reinstall the radiator cap.
5. Check that the coolant level is at the lower mark  (5:D1) in the expansion tank.
If necessary, top up with  coolant. See below.
5.4.1 Topping up with coolant
The coolant must meet the following require-
ments:
• Always use a mixture of refrigerant and water.  Never use just water.
• Mix the water and refrigerant according to the  refrigerant supplier’s instructions.
• Never mix different refrigerants.
• Use soft water (no calcium content), distilled or  demineralised water.
The engine must be cold when filling.
If the radiator cap is opened when the 
engine is hot there is  a risk of serious 
burn injuries from hot water that may 
spray out.
Top up as follows:
1. Remove the front  engine cover.
2. Check that all the plugs in the cooling system  are installed and sealed. . Check that all the taps in the cooling system are 
closed and sealed.
4. Check that all the hoses in the cooling system  are intact and sealed.
5. Unscrew the radiator cap (8:Q).
6. Slowly fill the radiator with coolant. Air bub- bles must not form when filling. Fill up to the 
filler hole.
7. Reinstall the radiator cap.
8. Open the cap on the expansion tank (5:D) and  top up the mixture to the lower mark which is 
the level when the engine is cold.
9. Close the cap for the expansion tank.
10.Run the engine to ope rating temperature and 
check the level in the expansion tank. The level 
should now be at the upper mark (5:D2), which 
is the level for when the engine is hot. 
11.If the level is not up to the upper mark, allow the  engine to cool and then top up with coolant in 
the expansion tank.5.5 AIR FILTER INDICATORCheck to make sure that the air filter indicator 
(5:I10) has not been tripped. 
Check, see 3.5.10.
Replace the air filter, see 6.13.
5.6 WATER SEPARATORCheck that the water separa tor’s float (9:C3) is at 
the bottom. If not, the water needs to be drained. 
See 6.4.
Check that the water sepa rator’s tap is open. See 
fig. 9.
5.7 SAFETY CHECKSCheck that the results of the safety checks below 
are met when testing the machine.
The safety checks must always be 
carried out before use.
If any of the results below are not met, 
the machine must not be used! Take the 
machine to a service workshop for 
repair. 
						

							87
ENGLISHEN
Original instructions for use
5.7.1 General safety checks
5.7.2 Electric safety checkThe safety system’s  function must 
always be checked before use.
5.8 START1.  Check that PTO is disengaged. 
2.  Do not keep your foot  on the accelerator pedal. 
3.  Set the throttle control to ¼ throttle. 
4.  Depress the brake pedal fully. The indicator  lamp (1:I4) should illuminate.
5.  For cold starts at lower temperatures, the engine  should be preheated before  starting. See 3.4.4.2. 
Then return the ignition key and start the en-
gine.
6. The machine must never be loaded or driven di- rectly after a cold start when the hydraulic oil is 
cold. Heat the hydraulic oil by running  the engine at 
¼ throttle.  Run it for a few minutes as shown in 
the diagram below..
Example: At -10°C run at ¼ throttle for 18 min-
utes.
When the machine is in operation, full throttle 
should always be used.
To prevent unnecessary in creases in pressure in 
the hydraulic system, set the throttle control to 
1/4 throttle before the hydraulic PTO is en-
gaged.
5.9 POWER ASSISTED STEERINGThe power steering transfers the force from the 
machine’s hydraulic system  to the steering wheel 
when turned. This makes the machine very easy to 
steer when the engine is running at full throttle. 
Power steering forces reduce as the engine speed 
reduces.
5.10 OPERATING TIPSAlways ensure that the correct amount of oil is in 
the engine. Especially when driving on slopes. 
See 5.3. 
Be careful when driving on slopes. No 
sudden starting or stopping when 
moving up or down a slope. Never drive 
across a slope. Move  from the top down, 
or from the bottom to the top. 
The machine must not be driven in any 
direction on slopes  with a gradient 
greater than 10º.
Reduce the speed on  slopes and when 
making sharp turns to prevent the 
machine from tipping over or you 
losing control.
Do not turn the steering wheel to full 
lock when driving in  top gear and at full 
throttle. The machine can easily topple 
over.
Keep hands and fing ers well away from 
the articulated steering joint and seat 
bracket. Risk of  crushing injuries. 
Never drive with the engine casing 
open.
Object Result
Fuel lines and 
connections.
No leak.
Power cables. All insulation intact. No mechanical damage.
Exhaust system. No leakage in the connections. All screws tightened.
Hydraulic hoses. No leakage. No damage.
Drive the machine 
forwards/back-
wards and release 
the drive/service 
brake pedal. The machine should stop.
Test driving. No unusual vibrations. No unusual noise.
Status Action Result
The clutch-brake 
pedal not depressed.
PTO not activated. Attempt to 
start.
The engine 
should not 
start.
The clutch-brake 
pedal not depressed.
PTO activated. Attempt to 
start.
The engine 
should not 
start.
Engine running. 
PTO activated. The operator 
leaves the seat.PTO should 
disengage.
Control for imple-
ment lifter not in 
floating position. Attempt to 
engage PTO.
PTO should 
not be able to 
be engaged. 
						

							88
ENGLISHEN
Original instructions for use
Depending on the implement used, 
counter weights might have to be 
mounted on the machine. The axle 
pressure  of a wheel axle may never 
exceed 900 kg or 70% of the total 
weight of the machine
5.11 STOPDisengage PTO. Apply the parking brake. 
Allow the engine to idle 1 - 2 mins. Stop the engine 
by turning off the starter key.If the machine is left unattended, 
remove the ignition key.
The engine may be very hot 
immediately after it is  shut off. Do not 
touch the silencer or other engine parts. 
This can cause burn injuries.
5.12 CLEANING
To reduce the risk of fire, keep the 
engine, silencer, battery and fuel tank 
free from grass, leaves and oil.
To reduce the risk of fire, regularly 
check the machine for oil and/or fuel 
leakage. 
Never use high-pressure water. This can 
damage shaft seals, electrical 
components or hydraulic valves.
Never use high-pressu re air against the 
radiator fins. This will damage the fin 
structure. 
Clean the machine after use. The following in-
structions apply to cleaning:
• Do not point jets of water directly at the engine. 
• Clean the engine with a brush and/or com- pressed air.
• Clean the engine’s radi ator (8:R) and condenser 
(8:S) with a soft brush.  Large objects can be  re-
moved by hand. If the coolers are heavily 
soiled, clean using slow running water and a 
suitable detergent.
• After cleaning with water, start the machine and  any cutting deck to remove the water that may 
otherwise penetrate bear ings and cause damage.
6 MAINTENANCE
6.1 SERVICE PROGRAMIn order to keep the machine in good condition, as 
regards reliability and operational safety as well as 
from an environmental pers pective, the service in-
structions in this section should be followed.
All services should be carried out by authorised 
workshops. Service, carried out by 
authorised workshops, 
guarantees a professional  job with original re-
placement parts.
The service log should be stamped at every service 
carried out by an authorised workshop. A “fully 
stamped” service log is a valuable document that 
improves the machine’s second-hand value.
The service points are given in the table below. De-
scriptions of how the pro cedures are to be carried 
out are given after the table.
6.2 SERVICE POINTS.
6.3 PREPARATIONAll service and all maintena nce must be carried out 
on a stationary machine with the engine switched 
off.
Prevent the machine from rolling by 
always applying the parking brake.
Stop the engine.
Prevent unintentional starting of the 
engine by removing the ignition key. 
Service point 1st time Interval See 
para-
graph
Hours of operation/
Calendar months
Water separator, 
check 50/- 6.4
Pre-filter, cleaning 6.4
Fuel filter, replace 400/- 6.5
Tyre pressure, 
check, adjust 6.6
Engine oil, filter, 
change 50/12 200/12 6.7
Hydraulic oil, fil-
ter, tank vent valve, 
change/clean 50/12 400/12 6.8
Wheel motors , 
change oil 50/12 200/12 6.9
Belt transmissions, 
check 50 200/- 6.10
Cooling system, 
clean 1000/12 6.11
Battery, check 50/- 6.12
Air filter, clean pre-
filter 250/- 6.13
Air filter, change 
inner filter 250/- 6.13
Lubrication 6.14
Adjusting valves 1000/- 6.15
Grinding valves 2000/- 6.15 
						

							89
ENGLISHEN
Original instructions for use
6.4 WATER SEPARATORThere is a float in the water separator (9:C3) that 
can be viewed through the transparent cup. The 
float must be at the bottom. If the float has risen, 
the water separator must be drained. 
To drain the water unscrew the drain tap (9:C1) un-
til the water begins to run. Drain until the float sits 
at the bottom again.
Clean the separator if the it  looks dirty or if it has 
to be drained often. The se parator is cleaned as fol-
lows:
1. Shut off the water separator tap. See fig. 9.
2. Hold a container under  the water separator to 
collect fuel.
3. Unscrew the cup. (9:C2).
4. Carefully remove the cup and remove the  thread filter (9:C5), the insert (9:C4), and the 
float (9:C3) from the cup.
5. Clean the inside of the cup and thread filter.
6. Check that the O-ring is intact and reinstall the  components in reverse order.
7. Open the tap.
Clean the fuel tank if water still often accumulates 
in the water separator. Contact an authorised work-
shop.
6.5 FUEL FILTER1. Stop the engine and allow it to cool.
2.  Close all the fuel taps.
3. Use an oil filter wrench to slacken off the filter  (5:F) in the direction (10:Dis). Carefully re-
move the filter to prevent the spillage of fuel.
Wipe up any spilled fuel.
4. Clean around the mounting surface of the filter.
5. Apply a thin layer of fuel to the new filter gas- ket.
6. Install the new filter by rotating it in the direc- tion (10:Ass) until the gasket comes into con-
tact with the mounting surface.
7. Then tighten the filter a further turn using the  filter wrench.
6.6 TYRE PRESSUREPressure front and back: 0.9 bar.
See pressures in the ma nual for relevant imple-
ment.
6.7 CHANGING ENGI NE OIL, FIL-
TER
The engine oil may be very hot if it is 
drained off directly  after the engine is 
shut off. So allow th e engine to cool a 
few minutes before draining the oil.
Change engine oil and filter as follows:
1. Place the machine on a le vel surface and run the 
engine to operating temperature. 2. Stop the engine and remove the oil filler cap 
(5:G).
3. Place a container under the oil drain plug  (11:U), remove the plug and let the oil run out 
into a container.
4. Dispose of the oil according to local regula- tions.
5. Clean the area around the oil filter (5:J) and re- move the filter. Use an  oil filter wrench.
6. Lubricate the gasket on  the new filter and screw 
this in until the gasket touches the surface of the 
engine. Then tighten the filter a further turn us-
ing an oil filter wrench.
7. Install the oil drain plug. Tighten to 50 Nm.
8. Fill with new oil according to 5.3.
9. After filling the oil, start the engine and run at  idle speed for 30 seconds. 
10.Check to see if there is any oil leakage.
11.Stop the engine. Wait for 30 seconds and then  check the oil level. See 5.3.
6.8 CHANGING HYDRAULIC OIL,  FILTER
No contaminants must enter the hy-
draulic system. This causes serious 
damage to components of the systems.
Change hydraulic oil and filter as follows:
1. Operate the machine at varying workload for 5- 10 minutes in order to warm up the hydraulic 
oil.
2. Place the machine on a level surface.
3. Clean the area around the filter (7:N) thorough- ly on the upper part of the hydraulic tank and re-
move the filter cup and the filter.
4. Place a container under th e oil drain plug (7:P), 
remove the plug and let the oil run out into a 
container. The container must have a capacity 
of 20 litres.
5. Dispose of the oil according to local regula- tions.
6. Install the oil drain plug. Tighten to 25 Nm.
7. Replace the tank vent va lve (7:O). The valve is 
unscrewed and the new one is installed in re-
verse order.
8. Reinstall the filter with the following compo- nents:
7:N1Filter cup. Clean the filter cup thorough before reinstalling.
7:N2 Gasket. Check that the washer is intact.
7:N3New filter. The filter must always be re- placed when changing the oil.
7:N4Spring
7:N5 Gasket. Check that the washer is intact.
7:N6Cover 
						

							90
ENGLISHEN
Original instructions for use
9. Fill with new oil through the 3/8” return for PTO, see fig. 1. Use a pump with 10 micron fil-
ter. 
Oil: See 2.1.
Oil quantity when changing: See 2.1.
10.After filling the oil, st art the engine and run the 
machine for a few minutes and check for oil 
leakage.
11.Check the oil level. See 3.5.11.
6.9 CHANGING THE OIL IN THE  WHEEL MOTORS
Change the oil in the gear housing of the wheel 
motors as follows:
1. Operate the machine at varying workload for 5-
10 minutes in order to warm up the oil in the 
wheel motors.
2. Place the machine on a level surface.
3. Clean carefully around the  oil plugs (12:V, W).
4. Place a container under the oil drain plug  (12:W), remove the plug and let the oil run out 
into a container.
5. Remove the filler plug (12:V).
6. Install the oil drain plug.
Dispose of the oil according to local regulations.
7. Fill with new oil via the filler plug hole. Pump  in the oil with help of an oil can. Fill until the 
level reach the the filler plug hole.
Regarding type and volume  of oil, see the table 
in 2.1.
8. Install the filler plug.
9. Tighten the plugs to 30 Nm.
6.10 BELT TRANSMISSIONSAfter 5 hours of operation check that all belts are 
intact and not damaged.
6.11 CLEANING THE COOLING SYS- TEM
All services should be carried out by authorised 
workshops.
6.12 BATTERY (7:M)
Acid that comes into contact with eyes 
or skin causes serious injury. If you 
come into contact with acid, 
immediately rinse with water and 
contact a doctor.
The battery is a valve-re gulated battery with 12 V 
nominal voltage. The battery  fluid does not need to 
and cannot be checked or topped up. The only 
maintenance that is required is charging, for exam-
ple after extended storage. The battery must be fully charged 
before being used for the first time. The 
battery must always be stored fully 
charged. If the batt
ery is stored while 
discharged, serious damage will occur. 
6.12.1 Charging with the engine
The battery can also be charged using the engine’s 
alternator as follows:
1. Install the battery in the machine as shown be- low.
2. Place the machine outdoors or install an extrac- tion device for the exhaust fumes.
3. Start the engine according to the instructions in  the user guide.
4. Allow the engine to run continuously for 45  minutes.
5. Stop the engine. The battery will now be fully  charged.
6.12.2 Charging using battery charger
When charging with the battery charger, a battery 
charger with continuous voltage must be used.
Contact your dealer to purchase a battery charger 
with constant voltage.
The battery can be damaged if a standard type 
battery charger is used. 
6.12.3 Removal/Installation The current must be cut using the main 
switch (1:F2) before  disconnecting the 
battery.
If the cables are interchanged, the 
generator and the battery will be 
damaged.
Tighten the cables securely. Loose 
cables can cause a fire.
The engine must neve r be driven with 
the battery disconnected. There is a risk 
of serious damage to  the alternator and 
the electrical system.
Remove/install the battery as follows:
1. Cut the power using the main switch (1:F2).
2. Remove the left-hand engine cover.
3. Disconnect the battery’s cable connections and  remove the battery.
4. Install the battery in re verse order. Connect the 
red cable to the battery’s positive terminal (+) 
and the black cable to the battery’s negative ter-
minal (-).
5. Activate the main switch.
6.12.4 Cleaning
If the battery terminals are coated with oxide, they 
should be cleaned. Clean the battery terminals with 
a wire brush a nd grease them using terminal 
grease.