Konica Minolta bizhub 420 User Manual

							Basic Copy Operations4
bizhub 500/420/360 (Phase 3) 4-33To specify paper type
Specify the special paper type for the bypass tray.
After a setting change has been made, the machine may adjust the fixing 
temperature or limit the output tray to be used depending on the specified 
paper type.
This setting also prevents the special paper loaded in bypass tray from being 
fed automatically when Auto Paper Select or Auto Tray Switch functions. 
When using OHP transparencies or any special paper, be sure to specify this 
setting to avoid unexpected feeding.
0This setting is indispensable for OHP transparencies, thick paper, or thin 
paper to be loaded in the bypass tray.
0Setting options are Recycled, Thick Paper, Thin Paper, OHP, Envelope, 
Letterhead, Trace, User, Labels, and Colored Paper.
0When printing on envelopes, open the right-hand door of the machine 
and pull up the envelope levers. For details, see To load paper into the 
bypass tray on page 3-61.
0The special paper setting of bypass tray will be cleared to the normal type 
setting, when the machine is reset to the initial setting.
1Touch [Paper] on the Basic Screen.
The Paper Screen will be displayed.
Downloaded From ManualsPrinter.com Manuals 
						

							4Basic Copy Operations
4-34 bizhub 500/420/360 (Phase 3)
2Touch the bypass tray key to highlight it, then touch [Change Tray 
Settings].
The Change Tray Settings Screen will be displayed.
3Specify the special paper type.
– Touch the desired paper type key to highlight it.
– To select Letterhead, Trace, User, Labels, or Colored Paper, touch 
[Specialty Paper].
Downloaded From ManualsPrinter.com Manuals 
						

							Basic Copy Operations4
bizhub 500/420/360 (Phase 3) 4-35– Touch the desired key to highlight it, then touch [OK].
4Touch [OK] twice.
The Copy Screen will be restored.
5Load paper of specified type into the 
bypass tray.
2
Reminder 
When loading special paper into the bypass tray, be sure to specify the 
corresponding paper type; otherwise paper misfeed may be caused.
2
Note 
If no other setting is desired, the copy job can be started using the 
settings currently specified without touching [OK] to return to the Basic 
Screen.
Downloaded From ManualsPrinter.com Manuals 
						

							4Basic Copy Operations
4-36 bizhub 500/420/360 (Phase 3)
4.7 Zoom Setting
Use this setting in order to make a copy using different-sized paper from the 
original, or to enlarge/reduce the image size.
The machine is initially set to make a copy in full size (e1.000) mode.
This section describes how to make the Zoom setting.
To copy in full size (e1.000) mode
Use this mode to make a copy of the same size as the original image 
irrespective of the paper size to be used.
0The full size (e1.000) mode is initially specified as default. If setting 
change has been made, follow the procedure below to specify this mode.
0Pressing [Reset] on the control panel will resume the full size (e1.000) 
mode, unless the initial setting with that mode specified has not been 
changed. In this case, other setting changes will also return to the initial 
condition.
0Use the [+] and [–] keys on the Zoom Screen to make a fine adjustment 
on specified magnification ratio. Touch [+] to increase, or [–] to decrease 
the ratio in 0.001 increments.
1Touch [Zoom] on the Basic Screen.
The Zoom Screen will be displayed.
Downloaded From ManualsPrinter.com Manuals 
						

							Basic Copy Operations4
bizhub 500/420/360 (Phase 3) 4-37
2Touch [×1.0] to highlight it.
3Touch [OK].
The Basic Screen will be restored with ×1.000 displayed on the Zoom 
key.
2
Note 
If no other setting is desired, the copy job can be started using the 
settings currently specified without touching [OK] to return to the Basic 
Screen.
Downloaded From ManualsPrinter.com Manuals 
						

							4Basic Copy Operations
4-38 bizhub 500/420/360 (Phase 3)To copy in slightly reduced magnification mode (Minimal)
A document Image can be printed slightly smaller (e0.930) than the original 
document size.
0The Minimal ratio is set to e0.930 as factory default.
0The Minimal ratio setting can be changed within the range from e0.900 to 
e0.999. For details, see To store a zoom ratio on page 4-51.
0Use the [+] and [–] keys on the Zoom Screen to make a fine adjustment 
on the specified magnification ratio. Touch [+] to increase, or [–] to 
decrease the ratio in 0.001 increments.
1Touch [Zoom] on the Basic Screen.
The Zoom Screen will be displayed.
2Touch [Minimal] to highlight it.
Downloaded From ManualsPrinter.com Manuals 
						

							Basic Copy Operations4
bizhub 500/420/360 (Phase 3) 4-39
3Touch [OK].
The Basic Screen will be restored with the specified magnification ratio 
displayed on the Zoom key.
2
Note 
If no other setting is desired, the copy job can be started using the 
settings currently specified without touching [OK] to return to the Basic 
Screen.
Downloaded From ManualsPrinter.com Manuals 
						

							4Basic Copy Operations
4-40 bizhub 500/420/360 (Phase 3)To select a preset zoom ratio
This machine is initially set to provide several magnification ratios (preset 
zoom ratio) often used to make a standard-sized copy from a standard-sized 
original. Select an appropriate ratio according to the original and copy paper 
sizes.
0Four types each for enlargement (e1.154, e1.224, e1.414, e2.000) and 
reduction (e0.866, e0.816, e0.707, e0.500)
0Use the [+] and [–] keys on the Zoom Screen to make a fine adjustment 
on the specified magnification ratio. Touch [+] to increase, or [–] to 
decrease the ratio in 0.001 increments.
1Touch [Zoom] on the Basic Screen.
The Zoom Screen will be displayed.
2Touch the desired preset key to highlight it.
Downloaded From ManualsPrinter.com Manuals 
						

							Basic Copy Operations4
bizhub 500/420/360 (Phase 3) 4-41
3Touch [OK].
The Basic Screen will be restored with the specified magnification ratio 
displayed on the Zoom key.
2
Note 
If no other setting is desired, the copy job can be started using the 
settings currently specified without touching [OK] to return to the Basic 
Screen.
Downloaded From ManualsPrinter.com Manuals 
						

							4Basic Copy Operations
4-42 bizhub 500/420/360 (Phase 3)To specify a desired zoom ratio 
A desired magnification ratio can be specified within the range from e0.250 
to e4.000, in order to make a copy in the same height-to-width proportion as 
the original.
0Use the control panel keypad to enter the desired magnification ratio, 
within the range from e0.250 to e4.000 in e0.001 increments.
0Entered ratio can be registered. For details, see To store a zoom ratio 
on page 4-51.
0Use the [+] and [–] keys on the Zoom Screen to make a fine adjustment 
on the specified magnification ratio. Touch [+] to increase, or [–] to 
decrease the ratio in 0.001 increments.
1Touch [Zoom] on the Basic Screen.
The Zoom Screen will be displayed.
2Touch [XY Zoom].
The XY Zoom Screen will be displayed.
Downloaded From ManualsPrinter.com Manuals