Konica Minolta bizhub 420 User Manual

							Utility 16
bizhub 500/420/360 (Phase 3) 16-79
4Adjust the dislocation of fold position on each paper size, referring to a 
sample copy made by using Half-Fold mode.
– Touch [2 Half-Fold Position] to display the Half-Fold Position 
Screen.
– Select the paper size to be adjusted, then touch [Test Copy].
The Test Copy Screen will be displayed.
– Press [Start] to make a sample copy. When completed, touch 
[Close] to return to the Half-Fold Position Screen.
– Compare the page widths of left and right pages to check the 
center line of the sample copy. Change the adjustment value if 
satisfactory result is not obtained.
Touch [+] to enter the adjustment value if the fold position is off the 
center to the right. (Range: 0.5 mm ~ 5.0 mm)
Contrary, touch [–] if it is off to the left. (Range: –0.5 mm ~ –5.0 mm)
– Repeat this procedure until a satisfactory result is obtained.
5Adjust the horizontal position of punch holes, referring to a sample 
copy made by using Punch mode.
– Touch [3 Punch Horizontal Position] to display the Punch Horizontal 
Position Screen.
Downloaded From ManualsPrinter.com Manuals 
						

							16Utility 
16-80 bizhub 500/420/360 (Phase 3)– Touch [Test Copy].
The Test Copy Screen will be displayed.
– Press [Start] to make a sample copy. When completed, touch 
[Close] to return to the Punch Horizontal Position Screen.
– Check the hole positions of the sample copy. Change the 
adjustment value if satisfactory result is not obtained.
Touch [+] to increase the adjustment value for shifting the hole 
positions to the right. (Range: 0.5 mm ~ 5.0 mm)
Contrary, touch [–] if it is off to the left. (Range: –0.5 mm ~ –5.0 mm)
– Repeat this procedure until a satisfactory result is obtained.
6Adjust the Punch Resist Loop Size, i.e., the slanted punch position in 
double-sided copies or in cover sheet, referring to a sample copy made 
by using Punch mode.
– Touch [4 Punch Resist Loop Size] to display the Punch Resist Loop 
Size Screen.
– Select the menu item to be adjusted, then touch [Test Copy].
The Test Copy Screen will be displayed.
Downloaded From ManualsPrinter.com Manuals 
						

							Utility 16
bizhub 500/420/360 (Phase 3) 16-81– Press [Start] to make a sample copy. When completed, touch 
[Close] to return to the Punch Resist Loop Size Screen.
– Check the hole positions of the sample copy.
Touch [+] or [–] to change the adjustment value if satisfactory result 
is not obtained.
Too much adjustment value may cause a fold at the end of paper.
– Repeat this procedure until a satisfactory result is obtained.
7Touch [OK] to complete the setting.
– To cancel the change, touch [Cancel].
In either case, the Expert Adjustment Screen will be restored.
8If further changes are required, touch the desired key.
Downloaded From ManualsPrinter.com Manuals 
						

							16Utility 
16-82 bizhub 500/420/360 (Phase 3)8 List/Counter>1 Management List
Use this function to print out the machine management lists.
1Follow the procedure described in How to access the Administrator 
Setting Screen on page 16-3 to display the Administrator Setting 
Screen.
2Touch [1 System Setting], [8 List/Counter], and then [1 Management 
List].
The Management List Screen will be displayed.
Downloaded From ManualsPrinter.com Manuals 
						

							Utility 16
bizhub 500/420/360 (Phase 3) 16-83
3Touch the desired list key.
– On the subsequent screen, select paper and simplex/duplex for 
printing the list, then press [Start] on the control panel.
To suspend printing, press [Stop].
4Touch [Close] repeatedly to return to the List/Counter Screen.
If further changes are required, touch the desired key.
Downloaded From ManualsPrinter.com Manuals 
						

							16Utility 
16-84 bizhub 500/420/360 (Phase 3)8 List/Counter>2 Paper Size/Type Counter
Use this function to register up to ten combinations of paper size and type to 
be counted.
1Follow the procedure described in How to access the Administrator 
Setting Screen on page 16-3 to display the Administrator Setting 
Screen.
2Touch [1 System Setting], [8 List/Counter], and then [2 Paper Size/Type 
Counter].
The Paper Size/Type Counter Screen will be displayed.
Downloaded From ManualsPrinter.com Manuals 
						

							Utility 16
bizhub 500/420/360 (Phase 3) 16-85
3Touch the number to clear the counter or change the setting.
4Touch [Change Setting] to change the setting.
– Touch the desired paper type key to highlight it.
– Touch change the paper size, touch [Paper Size] and then touch the 
desired paper size key to highlight it.
Downloaded From ManualsPrinter.com Manuals 
						

							16Utility 
16-86 bizhub 500/420/360 (Phase 3)– Touch [OK], to display the Confirmation Screen.
Touch [Yes].
To cancel the change, touch [No].
5Touch [Clear Counter] to clear the counter.
– The Confirmation Screen will be displayed.
– Touch [Yes] to clear the counter. 
To cancel the clearance, touch [No].
Downloaded From ManualsPrinter.com Manuals 
						

							Utility 16
bizhub 500/420/360 (Phase 3) 16-879 Reset Setting > 1 System Auto Reset
The machine can be set to automatically switch to the specified priority 
mode (Copy or Scan) after a certain period of machine inactivity.
This function is referred to as System Auto Reset.
Use this setting to specify the priority mode and period of time to be elapsed 
before the touch panel displays the priority mode screen.
According to the factory default, the machine will switch to the Copy mode 
with Basic Screen displayed after one minute of machine inactivity.
Downloaded From ManualsPrinter.com Manuals 
						

							16Utility 
16-88 bizhub 500/420/360 (Phase 3)
1Follow the procedure described in How to access the Administrator 
Setting Screen on page 16-3 to display the Administrator Setting 
Screen.
2Touch [1 System Setting], [9 Reset Setting], and then [1 System Auto 
Reset].
The System Auto Reset Screen will be displayed.
Downloaded From ManualsPrinter.com Manuals