Konica Minolta bizhub 420 User Manual

							Application Functions6
bizhub 500/420/360 (Phase 3) 6-89
7Select additional copy conditions, as desired.
8Press [Start] on the control panel.
The machine will start scanning the original, then printing when ready 
for output.
2
Note 
To release the selected application function, touch [OFF].
To release all the application functions, touch [Reset].
To resume the initial setting for all settings including application function, 
press [Reset] on the control panel.
2
Note 
If no other setting is desired, the copy job can be started using the 
settings currently specified without touching [OK] to return to the 
Application Screen or Basic Screen.
Downloaded From ManualsPrinter.com Manuals 
						

							6Application Functions
6-90 bizhub 500/420/360 (Phase 3)Erasing Black Marks along Center Fold (Center Erase)
This function erases black marks along the center fold of printed sheets 
which tend to be created when using the original glass to scan thick original 
such as a book.
Use this function also for the original already having black marks along the 
center fold.
To copy using Center Erase
0Available range for the erasure amount is 0.1 mm ~ 99.0 mm in 0.1 mm 
increments.
0Available to be used together with Erase.
When using Non-Image Area Erase in combination, scan the original from 
the original glass.
1Position the original.
2Enter the desired print quantity from the control panel keypad.
3Touch [Application] tab on the Basic Screen.
The Application Screen will be displayed.
Downloaded From ManualsPrinter.com Manuals 
						

							Application Functions6
bizhub 500/420/360 (Phase 3) 6-91
4Touch [Erase], then touch [Center Erase] again.
The Center Erase Screen will be displayed.
5Specify the erasure amount.
– Use [+] and [–], or control panel keypad to enter the desired erasure 
amount. In order to specify a fraction, touch the bidirectional arrow 
key to move the cursor, then use [+] and [–] to enter the desired 
value in 0.1 mm increments.
Downloaded From ManualsPrinter.com Manuals 
						

							6Application Functions
6-92 bizhub 500/420/360 (Phase 3)
?Do you want to change the currently entered value using control 
panel keypad?
%Press [C] (Clear) on the control panel, then enter the correct value.
?What if the value just entered is out of available range?
%The Input Error message will be displayed. Press [C] (Clear) on the 
control panel, then reenter the correct value.
6Touch [OK] to return to the Application Screen.
– Touch [Cancel] on the Center Erase Screen to cancel the setting 
change.
7Select additional copy conditions, as desired.
8Press [Start] on the control panel.
The machine will start scanning the original, then printing when ready 
for output.
2
Note 
To release the selected application function, touch [OFF].
To release all the application functions, touch [Reset].
To resume the initial setting for all settings including application function, 
press [Reset] on the control panel.
2
Note 
If no other setting is desired, the copy job can be started using the 
settings currently specified without touching [OK] to return to the 
Application Screen or Basic Screen.
Downloaded From ManualsPrinter.com Manuals 
						

							Application Functions6
bizhub 500/420/360 (Phase 3) 6-93Erasing Outside Area of Original (Non-Image Area Erase)
This function detects the original size placed on the original glass and erases 
outside area of the original.
To copy using Non-Image Area Erase
0Scan the original from original glass. Be sure to keep the ADF open.
0Original size should be larger than 30 mm e 30 mm
0Available to be used together with Erase and Center Erase.
1Position the original on the original glass.
2Enter the desired print quantity from the control panel keypad.
3Touch [Application] tab on the Basic Screen.
The Application Screen will be displayed.
4Touch [Erase] on the Application Screen.
The Erase Screen will be displayed.
Downloaded From ManualsPrinter.com Manuals 
						

							6Application Functions
6-94 bizhub 500/420/360 (Phase 3)
5Touch [Non-Image Area Erase] on the Erase Screen to highlight it.
6Touch [OK] to return to the Application Screen.
– To release the selected application function, touch [Non-Image 
Area Erase].
7Select additional copy conditions, as desired.
8Press [Start] on the control panel.
The machine will start scanning the original, then printing when ready 
for output.
Downloaded From ManualsPrinter.com Manuals 
						

							Application Functions6
bizhub 500/420/360 (Phase 3) 6-95
2
Note 
To release all the application functions, touch [Reset].
To resume the initial setting for all settings including application function, 
press [Reset] on the control panel.
2
Note 
If no other setting is desired, the copy job can be started using the 
settings currently specified without touching [OK] to return to the 
Application Screen or Basic Screen.
2
Reminder 
Non-Image Area Erase function may not operate properly for dark 
original. In this case, check this function using the original with white 
background.
This function may also perform incorrectly if the lighting in the work place 
is directly over the original glass. In this case, consult your service 
representative about an appropriate place for installation.
Downloaded From ManualsPrinter.com Manuals 
						

							6Application Functions
6-96 bizhub 500/420/360 (Phase 3)
6.14 Adjusting Position of Copy Image (Image Adjustment)
Use this function to make a copy adjusting the position of printed image.
The original size can be either detected automatically or specified manually.
-Centering
The original image will be centered on copy paper.
-No Rotate
For example, when size A4 copy paper is loaded in lengthwise (w) 
orientation and the machine detects that the size A4 original is placed 
portrait (v), the Rotation operates to make the same size copy as if using 
size A4 copy paper loaded in crosswise (v) orientation by rotating the 
original image 90°.
Also, the large original (such as A3 or B 4 )  t o  b e  p o s i t i o n e d  o n l y  l a n d s c a p e  
(w) can be copied onto copy paper loaded in crosswise (v) orientation 
(such as A4 or B5) with Auto Zoom activated to reduce the image size.
Specify [No Rotate] to disable this function.
Function overview
The following two modes are provided for the Image Adjustment function. 
These are compatible with each other.
ModeDescription
Centering
No Rotate
Original Copy CopyOriginal
Downloaded From ManualsPrinter.com Manuals 
						

							Application Functions6
bizhub 500/420/360 (Phase 3) 6-97Copying Image in the Center of Copy Paper (Centering)
Use this function to center the whole original image on copy paper.
0Scan the original from original glass. Be sure to keep the ADF open.
Non-Image Area Erase functions automatically.
0With Centering selected, the machine will operate Auto Detect 
automatically. The Standard Size setting is incompatible.
0Auto Zoom is incompatible.
1Position the original.
2Enter the desired print quantity from the control panel keypad.
3Touch [Application] tab on the Basic Screen.
The Application Screen will be displayed.
4Touch [Image Adjustment] on the Application Screen.
The Image Adjustment Screen will be displayed.
Downloaded From ManualsPrinter.com Manuals 
						

							6Application Functions
6-98 bizhub 500/420/360 (Phase 3)
5Touch [Centering] on the Image Adjustment Screen to highlight it.
6Touch [OK] to return to the Application Screen.
– Touch [Cancel] on the Image Adjustment Screen to cancel the 
setting change.
7Select additional copy conditions, as desired.
– The machine automatically selects tray 1 as factory default. To 
specify the paper size, touch [Paper] to display the Paper Screen, 
then touch the desired tray key to highlight it.
8Press [Start] on the control panel.
The machine will start scanning the original, then printing when ready 
for output.
Downloaded From ManualsPrinter.com Manuals