Konica Minolta bizhub 420 User Manual

							Application Functions6
bizhub 500/420/360 (Phase 3) 6-49
2
Reminder 
Non-Image Area Erase function may not operate properly for dark 
original. In this case, check this function using the original with white 
background.
This function may also perform incorrectly if the lighting in the work place 
is directly over the original glass. In this case, consult your service 
representative about an appropriate place for installation.
2
Note 
To release the selected application function, touch [OFF].
To release all the application functions, touch [Reset].
To resume the initial setting for all settings including application function, 
press [Reset] on the control panel.
2
Note 
If no other setting is desired, the copy job can be started using the 
settings currently specified without touching [OK] to return to the 
Application Screen or Basic Screen.
Downloaded From ManualsPrinter.com Manuals 
						

							6Application Functions
6-50 bizhub 500/420/360 (Phase 3)
6.8 Repeating Original Image on One Sheet (Image 
Repeat)
Use this function to print the original image repeatedly on a single sheet of 
paper.
The following two modes are provided for Image Repeat.
-Auto Repeat
Use the original glass to scan the original.
The machine automatically determines the number of repeats from 
detected original image size and paper size.
The original image size can be both detected automatically (Auto Detect) 
or specified manually (Set Range).
Also select whether to print the defective images around the edges 
(Without Margin), or to leave the marginal area blank without printing 
defective images (With Margin).
-2/4/8 Repeat
Use the ADF or original glass to scan the original.
Specify the number of repeats from 2, 4, and 8 times, irrespective of the 
original image size.
The original image size can be both detected automatically (Auto Detect) 
or specified manually (Set Range).
Downloaded From ManualsPrinter.com Manuals 
						

							Application Functions6
bizhub 500/420/360 (Phase 3) 6-51Function overview
FunctionModeDescription
Auto Repeat Auto Detect + With 
Margin
Auto Detect + Without 
Margin
Set Range + With 
Margin
Set Range + Without 
Margin
2/4/8 Repeat 2 Repeat
4 Repeat
8 Repeat
Downloaded From ManualsPrinter.com Manuals 
						

							6Application Functions
6-52 bizhub 500/420/360 (Phase 3)Setting Repeat Times Automatically
Select the Auto Detect or Set Range mode to automatically detect or 
manually specify the original image size, then let the machine determine the 
number of repeats from specified mode and magnification ratio.
0Scan the original from original glass. The ADF cannot be used to scan the 
original.
0Auto Detect mode uses Non-Image Area Erase function to automatically 
detect the original size. Keep the ADF open.
0Set Range mode does not use Non-Image Area Erase function. Close the 
ADF.
0Use Set Range mode to repeat a part of the original, not the entire image, 
by specifying the scanning area.
Select the standard size or enter the dimensions of custom size.
Available dimensions: 30.0 ~ 432.0 mm for side X, 30.0 ~ 297.0 mm for 
side Y
0Select With Margin to leave the marginal area blank without printing 
defective images. Or, select Without Margin to print the defective images 
around the edges.
0Tray 1 will be automatically selected as copy paper tray source.
Change the tray selection manually, if desired. Auto Paper Select will not 
function.
0Auto Zoom will not function. Specify the desired magnification ratio.
1Position the original on the original glass.
– Keep the ADF open.
2Enter the desired print quantity from the control panel keypad.
3Load the desired copy paper into any tray.
Downloaded From ManualsPrinter.com Manuals 
						

							Application Functions6
bizhub 500/420/360 (Phase 3) 6-53
4Specify the paper tray on the Paper Screen.
– Touch [Paper] on the Basic Screen to display the Paper Screen.
– Touch the desired tray key to highlight it. Without this tray selection, 
the machine will automatically use copy paper loaded in tray 1 to 
print.
5Touch [Application] tab on the Basic Screen.
The Application Screen will be displayed.
Downloaded From ManualsPrinter.com Manuals 
						

							6Application Functions
6-54 bizhub 500/420/360 (Phase 3)
6Touch [Book Copy/Repeat], then touch [Image Repeat].
The Image Repeat Screen will be displayed.
7Specify the desired Layout mode.
– Touch [With Margin] or [Without Margin] to highlight it.
Downloaded From ManualsPrinter.com Manuals 
						

							Application Functions6
bizhub 500/420/360 (Phase 3) 6-55
8Specify the desired Scan Range mode.
– To detect the original size automatically, touch [Auto Detect].
Non-Image Area Erase will also be selected automatically.
– To specify the scanning area, touch [Set Range] to display the 
Standard Size Screen, then select the desired scanning area.
Use up/down arrow key to scroll to the desired size, if necessary.
Downloaded From ManualsPrinter.com Manuals 
						

							6Application Functions
6-56 bizhub 500/420/360 (Phase 3)– To enter the dimensions of scanning area, touch [Custom Size] on 
the Standard Size Screen to display the Custom Size Screen, then 
enter the desired dimensions from the control panel keypad. In 
order to specify a fraction, touch the bidirectional arrow key to 
move the cursor, then use [+] and [–] to enter the desired value in 
0.1 mm increments.
– When [Set Range] is selected, close the ADF.
?Do you want to delete the dimensions once entered?
%Press [C] (Clear) on the control panel, then enter the correct 
dimensions.
9Touch [OK] to return to the Application Screen.
– Touch [Cancel] on the Image Repeat Screen, Standard Size Screen 
or Custom Size Screen to cancel the setting change.
10Select additional copy conditions, as desired.
– Specify the desired magnification.
The number of repeats will be determined automatically from 
specified scanning area, selected paper size and magnification 
ratio.
11Press [Start] on the control panel.
The machine will start printing when ready for output.
Downloaded From ManualsPrinter.com Manuals 
						

							Application Functions6
bizhub 500/420/360 (Phase 3) 6-57
2
Note 
To release the selected application function, touch [OFF].
To release all the application functions, touch [Reset].
To resume the initial setting for all settings including application function, 
press [Reset] on the control panel.
2
Note 
If no other setting is desired, the copy job can be started using the 
settings currently specified without touching [OK] to return to the 
Application Screen or Basic Screen.
Downloaded From ManualsPrinter.com Manuals 
						

							6Application Functions
6-58 bizhub 500/420/360 (Phase 3)Specifying Repeat Times (2/4/8 Repeat)
Use this function to specify the number of repeats from 2, 4, and 8 times, 
irrespective of the original image size.
0Position the original on the original glass or in the ADF.
0Use Set Range mode to repeat a part of the original, not the entire image, 
by specifying the scanning area.
Select the standard size or enter the dimensions of custom size.
Available dimensions: 30.0 ~ 432.0 mm for side X, 30.0 ~ 297.0 mm for 
side Y
0Select With Margin to repeat the image within the printing area leaving 3 
mm from the leading edge, 4 mm from the rear edge, and 2 mm each 
from left and right edges of selected paper size.
When Without Margin is selected, the original image will be repeated to 
the margin area in which an image loss is likely.
0With 2 Repeat selected, the interval between the two copy images can 
be adjusted by Repeat Interval Setting.
0Tray 1 will be automatically selected as copy paper tray source.
Change the tray selection manually, if desired. Auto Paper Select will not 
function.
0Auto Zoom will not function. Specify the desired magnification ratio.
1Position the original.
2Enter the desired print quantity from the control panel keypad.
3Load the desired copy paper into any tray.
Downloaded From ManualsPrinter.com Manuals