Konica Minolta bizhub 420 User Manual

							Application Functions6
bizhub 500/420/360 (Phase 3) 6-119
4Touch [Stamp/Overlay], then touch [Built-in Stamp].
The Built-in Stamp Screen will be displayed.
5Select the desired stamp type and pages to print.
– Touch one of the eight stamp type keys to highlight it.
– Touch either of the two keys under Pages to highlight it.
– Touch [Change Size] to select Large Size or Small Size.
Downloaded From ManualsPrinter.com Manuals 
						

							6Application Functions
6-120 bizhub 500/420/360 (Phase 3)– To change or make fine adjustment on the print position currently 
specified as indicated on the Print Position key, proceed to the next 
step.
To complete this setting, proceed to step 8.
6Touch [Print Position] to display the Print Position Screen.
– Touch one of the nine Print Position keys to highlight it.
– If fine adjustment is not required, proceed to step 8.
7Touch [Change Adjustment] to display the Fine-Tune Screen.
– Touch [Left] or [Right] under Left & Right Adjustment to highlight it. 
Use [+] and [–] to enter a fraction in 0.1 mm increments. Touch the 
bidirectional arrow key to move the cursor, then use [+], [–], or 
control panel keypad to enter whole number part of the desired 
value.
Similarly, touch [Top] or [Bottom] under Top & Bottom Adjustment 
to highlight it, then enter the desired adjustment value.
To deactivate these adjustment, touch [No Adj.] for each.
Downloaded From ManualsPrinter.com Manuals 
						

							Application Functions6
bizhub 500/420/360 (Phase 3) 6-121
?Do you want to change the currently entered value using control 
panel keypad?
%Press [C] (Clear) on the control panel, then enter the correct value.
?What if the value just entered is out of available range?
%The Input Error message will be displayed. Press [C] (Clear) on the 
control panel, then reenter the correct value.
8Touch [OK] to return to the Application Screen.
– Touch [Cancel] on the Built-in Stamp Screen, Print Position Screen, 
or Fine-Tune Screen to cancel the setting change.
9Select additional copy conditions, as desired.
10Press [Start] on the control panel.
The machine will start scanning the original, then printing when ready 
for output.
2
Note 
To release the selected application function, touch [OFF].
To release all the application functions, touch [Reset].
To resume the initial setting for all settings including application function, 
press [Reset] on the control panel.
2
Note 
If no other setting is desired, the copy job can be started using the 
settings currently specified without touching [OK] to return to the 
Application Screen or Basic Screen.
Downloaded From ManualsPrinter.com Manuals 
						

							6Application Functions
6-122 bizhub 500/420/360 (Phase 3)Printing Watermark onto Copies (Watermark)
0Select one from the eight watermark types provided on the screen.
1Position the original.
2Enter the desired print quantity from the control panel keypad.
3Touch [Application] tab on the Basic Screen.
The Application Screen will be displayed.
Downloaded From ManualsPrinter.com Manuals 
						

							Application Functions6
bizhub 500/420/360 (Phase 3) 6-123
4Touch [Stamp/Overlay], then touch [Watermark].
The Watermark Screen will be displayed.
5Select the desired watermark type.
– Touch one of the eight keys to highlight it.
6Touch [OK] to return to the Application Screen.
– Touch [Cancel] on the Watermark Screen to cancel the setting 
change.
Downloaded From ManualsPrinter.com Manuals 
						

							6Application Functions
6-124 bizhub 500/420/360 (Phase 3)
7Select additional copy conditions, as desired.
8Press [Start] on the control panel.
The machine will start scanning the original, then printing when ready 
for output.
2
Note 
To release the selected application function, touch [OFF].
To release all the application functions, touch [Reset].
To resume the initial setting for all settings including application function, 
press [Reset] on the control panel.
2
Note 
If no other setting is desired, the copy job can be started using the 
settings currently specified without touching [OK] to return to the 
Application Screen or Basic Screen.
Downloaded From ManualsPrinter.com Manuals 
						

							Application Functions6
bizhub 500/420/360 (Phase 3) 6-125Overlay an Image onto Each Page Copied in the Job (Image Overlay)
0Separate Scan mode is automatically selected.
1Position the overlaying original.
Position the original FACE up in the document feeder or FACE DOWN 
on the original glass.
2Touch [Application] tab on the Basic Screen.
The Application Screen will be displayed.
Downloaded From ManualsPrinter.com Manuals 
						

							6Application Functions
6-126 bizhub 500/420/360 (Phase 3)
3Touch [Stamp/Overlay], then touch [Image Overlay] to highlight it.
– Auto Zoom and Auto Paper Select are automatically released, and 
1.000 (100%) is selected as a magnification ratio.
– To specify the desired copy conditions for overlaying original, touch 
[OK] to continue.
4Press [Start] on the control panel.
The original image will be scanned into memory, and the following 
screen will be displayed.
Downloaded From ManualsPrinter.com Manuals 
						

							Application Functions6
bizhub 500/420/360 (Phase 3) 6-127
5Position the original to be overlaid.
6Press [Start] to scan.
– Repeat steps 5 and 6 for all originals.
7Touch [Complete Scan] on the Basic Screen.
8Press [Start].
The machine will start printing when ready for output.
2
Note 
To release all the application functions, touch [Reset].
To resume the initial setting for all settings including application function, 
press [Reset] on the control panel.
2
Note 
If no other setting is desired, the copy job can be started using the 
settings currently specified without touching [OK] to return to the 
Application Screen or Basic Screen.
Downloaded From ManualsPrinter.com Manuals 
						

							6Application Functions
6-128 bizhub 500/420/360 (Phase 3)Storing Image on HDD / Overlaying Stored Image (Store Overlay)
To make a copy using the image previously stored, start with step 9.
1Position the overlaying original.
Position the original FACE up in the document feeder or FACE DOWN 
on the original glass.
2Touch [Application] tab on the Basic Screen.
The Application Screen will be displayed.
Downloaded From ManualsPrinter.com Manuals