Konica Minolta bizhub 420 User Manual

							Application Functions6
bizhub 500/420/360 (Phase 3) 6-79
6Specify the binding margin.
– Use [+] and [–] to enter the desired value in 0.1 mm increments.
– When [None] is highlighted, the margin is automatically set to 0 mm.
Use [None] for correcting the image orientation of double-sided 
copy.
?What should be done if wrong value is entered?
%Press [C] (Clear) on the control panel, then reenter the correct value.
?What if the value just entered is out of available range?
%The Input Error message will be displayed. Press [C] (Clear) on the 
control panel, then reenter the correct value.
?Is it available to change the binding position even if the margin is 
already specified?
%Yes. The binding position can be changed at any time.
7Touch [OK] to return to the Application Screen.
– Touch [Cancel] on the Page Margin Screen to cancel the setting 
change.
8Select additional copy conditions, as desired.
9Press [Start] on the control panel.
The machine will start scanning the original, then printing when ready 
for output.
Downloaded From ManualsPrinter.com Manuals 
						

							6Application Functions
6-80 bizhub 500/420/360 (Phase 3)
2
Note 
To release the selected application function, touch [OFF].
To release all the application functions, touch [Reset].
To resume the initial setting for all settings including application function, 
press [Reset] on the control panel.
2
Note 
If no other setting is desired, the copy job can be started using the 
settings currently specified without touching [OK] to return to the 
Application Screen or Basic Screen.
Downloaded From ManualsPrinter.com Manuals 
						

							Application Functions6
bizhub 500/420/360 (Phase 3) 6-81Adjusting Image Position on Front/Back Sides (Edit Margin)
This function creates a binding margin by shifting the position of scanned 
image as desired.
Also, a fine adjustment can be made separately for front and back side 
images when making double-sided copy.
To copy using Edit Margin
0The position of scanned image can be shifted both in lengthwise 
direction (Top & Bottom Shift) and in widthwise direction (Left & Right 
Shift).
0Available range for the shift amount is 0.1 mm ~ 250.0 mm in 0.1 mm 
increments.
0The front- and back-side images of double-sided copy can be shifted 
separately in order to correct the image dislocation.
1Position the original.
2Enter the desired print quantity from the control panel keypad.
3Touch [Application] tab on the Basic Screen.
The Application Screen will be displayed.
Downloaded From ManualsPrinter.com Manuals 
						

							6Application Functions
6-82 bizhub 500/420/360 (Phase 3)
4Touch [Page Margin], then touch [Edit Margin].
The Edit Margin Screen will be displayed.
5Specify the shift direction and amount.
– Touch [Left] or [Right] to shift the image in widthwise direction.
Use [+] and [–] to enter a fraction in 0.1 mm increments. Touch the 
bidirectional arrow key to move the cursor, then use [+], [–], or 
control panel keypad to enter whole number part of the desired 
value.
– Touch [Top] or [Bottom] to shift the image in lengthwise direction. 
Use [+] and [–] to enter a fraction in 0.1 mm increments. Touch the 
bidirectional arrow key to move the cursor, then use [+], [–], or 
control panel keypad to enter whole number part of the desired 
value.
Downloaded From ManualsPrinter.com Manuals 
						

							Application Functions6
bizhub 500/420/360 (Phase 3) 6-83– To clear the setting, touch [No Shift]. Press [C] (Clear) on the control 
panel to clear the setting in both directions.
– Proceed to the next step to adjust the position of the back-side 
image. If this adjustment is not required, proceed to step 7.
– Without a specific adjustment, the following settings will be applied 
to the back-side image.
Shift direction: Opposite to the front-side image
Shift amount: Same as the front-side image
?Do you want to delete the shift amounts once entered?
%Press [C] (Clear) on the control panel, then enter the correct 
dimensions.
?What should be done if the message Input Error is displayed?
%Press [C] (Clear) on the control panel, then reenter the correct value.
?Is it available to change the shift direction even if the shift amount 
is already specified?
%Yes. The shift direction can be changed at any time.
Downloaded From ManualsPrinter.com Manuals 
						

							6Application Functions
6-84 bizhub 500/420/360 (Phase 3)
6Adjust the position of the back-side image.
– Touch [Edit 2nd Side] on the Edit Margin Screen to display the Edit 
2nd Side Screen.
– Specify the shift direction and amount of the back-side image 
similarly in step 5.
7Touch [OK] to return to the Application Screen.
– Touch [Cancel] on the Page Margin Screen, Edit Margin Screen, or 
Edit 2nd Side Screen to cancel the setting change.
8Select additional copy conditions, as desired.
9Press [Start] on the control panel.
The machine will start scanning the original, then printing when ready 
for output.
2
Note 
To release the selected application function, touch [OFF].
To release all the application functions, touch [Reset].
To resume the initial setting for all settings including application function, 
press [Reset] on the control panel.
2
Note 
If no other setting is desired, the copy job can be started using the 
settings currently specified without touching [OK] to return to the 
Application Screen or Basic Screen.
Downloaded From ManualsPrinter.com Manuals 
						

							Application Functions6
bizhub 500/420/360 (Phase 3) 6-85
6.13 Erasing Specified Area of Copy (Erase)
When the original is scanned from the original glass, black copy marks may 
be produced along borders and center line, and also around punch holes.
Use this function to eliminate them from the copies and lower the toner 
consumption at the same time.
Function overview
The following three modes are provided for the Erase function. These are 
compatible with each other.
ModeDescription
Erase Erases black copy marks along borders of the original image.
Center Erase Erases black copy marks along the center line of the original.
Non-Image Area 
EraseDetects the original size and erases outside area of the original.
Downloaded From ManualsPrinter.com Manuals 
						

							6Application Functions
6-86 bizhub 500/420/360 (Phase 3)Erasing Black Marks along Borders (Erase)
This function erases black marks along the borders of printed sheets which 
tend to be created when using the original glass to scan thick original such 
as a book.
Use this function also for the original already having black marks along 
borders.
To copy using Erase
0Available range for the erasure amount is 0.1 mm ~ 300.0 mm in 0.1 mm 
increments.
0The erasure amount can be specified both collectively for all four sides 
and individually for each side.
0Available to be used together with Center Erase.
When using Non-Image Area Erase in combination, scan the original from 
the original glass.
1Position the original.
2Enter the desired print quantity from the control panel keypad.
3Touch [Application] tab on the Basic Screen.
The Application Screen will be displayed.
Downloaded From ManualsPrinter.com Manuals 
						

							Application Functions6
bizhub 500/420/360 (Phase 3) 6-87
4Touch [Erase], then touch [Erase] again.
The Erase Screen will be displayed.
Downloaded From ManualsPrinter.com Manuals 
						

							6Application Functions
6-88 bizhub 500/420/360 (Phase 3)
5Specify the erasing position and erasure amount.
– To specify the erasure amount collectively for all four sides, touch 
[Frame] to highlight it.
– To specify the erasure amount individually for each side, touch the 
desired side key to highlight it.
Use [+] and [–] to enter a fraction in 0.1 mm increments. Touch the 
bidirectional arrow key to move the cursor, then use [+], [–], or 
control panel keypad to enter whole number part of the desired 
value. Or, touch [None] to void the function on that side.
?Is it available to select [Frame] and other four keys ([Top], [Left], 
[Right], and [Bottom]) at the same time?
%No. Use [Frame] only for specifying the same erasure amount 
collectively for all four sides.
?Do you want to change the currently entered value using control 
panel keypad?
%Press [C] (Clear) on the control panel, then enter the correct value.
?What if the value just entered is out of available range?
%The Input Error message will be displayed. Press [C] (Clear) on the 
control panel, then reenter the correct value.
?Is it available to change the side to be erased even if the erasure 
amount is already specified?
%No.
6Touch [OK] to return to the Application Screen.
– Touch [Cancel] on the Erase Screen to cancel the setting change.
Downloaded From ManualsPrinter.com Manuals